Spring spacers MAF

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 14, 2008
Threads
52
Messages
1,275
Location
Wenatchee, Wa
I searched Man A Fre Spring spacers and didnt find what I was looking for. I am looking to give my 95 a little more altitude, not a lot just a little. It is all stock, the front end is completely rebuilt and needless to say with going back to college and a 6 month old I dont have the funds for a 2.5 medium lift!

I saw where toolsrus can make 1" to 1.5" steel spacers and looked at the MAF spring spacers.

Does anybody have just a spacer lift on their landcruiser that would lend some pics for my inquiring mind. I still have stock tires but will probably wait to upgrade when they wear out!

I am not new to Mud, just a new username, so dont flog me for not searching! :flipoff2:
 
If this is the route you want to go call up metal tech and talk to them.
 
I purchased some Man A Fre 30mm spacers for the front. They're out of Australia. Only been on the truck a week or so but they were relatively inexpensive and seem pretty tough. They have fronts and rears.
 
I purchased some Man A Fre 30mm spacers for the front. They're out of Australia. Only been on the truck a week or so but they were relatively inexpensive and seem pretty tough. They have fronts and rears.

that was my forst lift in Marilu .. they hold pretty good for a year or so.. then replace my coils and now I'm still running 'em in front .. ( to level my suspension ) they still hold pretty well with no visible wear ..
 
been running MAF spacers for 3 years......they do what they are suppose to do and they are cheap.........no issues so far.



.
 
What are you guys running as far as tires with these spacers. I think I might end up going the Metal-tech route just so I can get 2 inches out of it.

For you guys with the spacers did you go 2 inch front and rear or 2 inch front 1.5 rear?

I read that caster correction is required (or highly recommended) so what is the best route of doing this? Kit or???

BTW thanks for the tips guys!
 
Measure your center hub to flare/fender height front and rear. Then decide how level a stance you want. My rig is very level right now. I'm at 24 1/2" in front and 25 1/4" in the rear unloaded. Now if I load it up for a weekend or what of camping it might be sagging a touch in the rear, but most of the time i'm not loaded with much, plus i'm planning to add a second battery up front and maybe a winch. I had some serious stink bug before and this was the cheapest, simplest route to leveling my rig. As far a 2" of lift goes you can just do some OME yellow caster correction bushings and I think you'll be set. You can run 285's or 305's and not re-gear and it'll look good. You can fit 315's (which is what i want, my 305's look tiny) but you probably want to re-gear at the same time and lower your bump stops to keep the tires from hitting your fenders.
 
But yours has aftermarket suspension?
 
I could be wrong but I don't think metaltech sells rear spacers, only fronts. If its front and back you want then MAF spacers will work for you.

I'm running 285's with no isssues at all with mine.

Caster correction isn't really necessary with these spacers unless you are really fussy about the handling. I have only noticed a slight wander effect on the highway which really isn't that bad and certainly manageable.


.
 
IMO I'd be surprised if you need CC with just running spacers. Although trucks vary. You will not do any serious harm running without CC to the truck. I would install, get your CC measured, get the numbers and decide on the proper CC correction if needed.

OME ~2* Correction
Slee ~3* Correction
LandTank & Slee Plates IIRC ~4-5*
 
But yours has aftermarket suspension?

Yes. This is why i really need some 315's and 4.88's! :doh: In any case I'd suggest you just doing the Man a Fre 1" spacers all around and get some 285's or 305's and don't worry about caster correction. If you were planning 2" maybe you'd want to look at caster correction. Even then it's a maybe.... 1" won't be an issue.
 
Well basically what i need to do is just save my money and get a 2.5 inch lift. I wanted to do this on the cheap but i dont wanna jerry rig it, the spacers look good to level things out but not to acheive what i want to
 
Back
Top Bottom