SOA-Rear shocks

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Cruiserdrew

On the way there
Joined
Mar 15, 2003
Threads
219
Messages
15,839
Location
Sacramento, CA
Before you ask, I have searched and the Rancho 9012s look like the ticket for the front of my new SOA. THat part # is mentioned several times, and Mark W seems especially fond of this shock. That's good enough for me.

I'm having some trouble figuring out the rears. The 9012s seem too long when compressed for my intended mounting scheme-Stock upper mounts and shock mounted to the top of axle itself just inside the perches. I have FJ60 springs and roughly stock length shackles.

I need some ideas on shock mounting locations, and shock lengths that worked for you. Since what I have now is just a chassis, it's hard to flex it out and get good measurments.

So, school me on mounting scemes, shock locations, and shocks that you like. Part #s would be very welcome. If there is a Rancho 9000 series shock that works here, that would be nice.
 
I have 9114's on mine.
My rear upper mounts were put on the rear of the cross member and I have stock 40 springs, turned for wheel base.
IIRC its a fairly common setup.
Good luck
Edit for a pic, Hope it helps...
Traction bar.webp
 
Last edited:
That mounting scheme is a bad idea. Too close together. Any shock that will fit there will be the limiting point of your suspension. Even plain old suspension travel, much less articulation.

Move your mounting points. Put them at the lowest point on the axle/OEM perch that you can without hanging them down to snag and move the upper mounting point inwards. Then use... 99012s ;)


Mark...
 
I used 9112s in the back of the cruiser. Mounted the bottom end to the side of the axle tube and the tops I redrilled the crossmember close to the center. I have to keep them at the stiffest setting cause the angle of the mounting position decreases their dampening ability. If you need a pic just e-mail me...I don't feel like resizing one at the moment;p

Oh yes, my rig is SOA. Didn't see what yours was...SOA or SUA?
 
Thanks-It's SOA. How does one mount the lower mount? Mounting to the rear side of the axle looks good, but exactly how do you mount it? I don't want anything to hang under that I'll just knock off. I took some measurments given various locations, and I don't really see a way to use the 9012's in the rear.
 
Thanks-It's SOA. How does one mount the lower mount? Mounting to the rear side of the axle looks good, but exactly how do you mount it? I don't want anything to hang under that I'll just knock off. I took some measurments given various locations, and I don't really see a way to use the 9012's in the rear.

Weld a shock pin on.

A couple of the guys that run with me have tried to get away with running (shorter) shocks they already had and/or mounting the way you are considering. A few busted shocks and shock mounts later, they gave up. The next longest Ranchos have about 10 inches of travel IIRC. Not enough. I'd be surprised if you could fit those anyway in the configuration you are looking at.

I've mounted 9012s and 99012s in at least a couple dozen SOA rigs.


Mark...
 
Thanks-It's SOA. How does one mount the lower mount? Mounting to the rear side of the axle looks good, but exactly how do you mount it? I don't want anything to hang under that I'll just knock off. I took some measurments given various locations, and I don't really see a way to use the 9012's in the rear.

Andy, several of the Rancho shocks are actually supplied with mounting studs. You can cut the large threaded end off and weld the rest to the axle tube. Tha's what I just did on the 45 to compensate for loosing my stock u-bolt plates.

I suppose since you're hooking me up with that pitman arm, I could send you a pair of thse bolts if you decide to go that route.;)

Another would be to get a pair of shock mounting tabs that gravel maker sells that you can weld to the backside of the axle tube on any angle you like. I used tabs like his many years ago when I briefly experimented with SOA on my 40.

And FWIW, I would inboard the upper shock mounts to take advantage of a longer shock. I intend to do this on the 45 soon.

Best

Mark A.
 
Last edited:
Channel iron (well it is about 1/4 of a square tube chunk anyways but channel would be the same) and drill a hole to weld the stud into. For the top...drill and hole and put a bolt through it and tack it in.
 
Last edited:
I finally got pics and e-mailed them to you tonight. :doh:
Here is what I did:
Lower mount:
Dscn1922.jpg

I made these using a bolt and a piece of flat stock. Since I flipped the springs, I pointed the bolt backwards to center the shock over the axel when using the stock upper mounts.

Probably not the best angle, but the rears will compress until the hit the inner fenders. I'm not sure if I am restricting the droop, I still need to remove the shocks, jack the rig up and take some measurments.

Dscn1924.jpg


Overall I'm pretty happy with the articulation.

Dscn1807.jpg
 
Vitesse-6---Those look like the stock mounts off of a 40. Is that where you sourced them? Something like that could work for me. I have a set off an old FJ40 axle I could cut off and use, or at least try.

Tankota-That's a good idea, and appealing because it's something my limited fab skills could handle.


Mark-Deal on the bolts, but make sure you like the Pitman arm first. I did have to hack it to get the puller on it. I was thinking of using the bolts from the stock front shock towers. If the backside was just a bit longer it would be perfect.

Rusty-Thanks again for the email pics. I am hoping to use a longer shock than you show, but the way you did it obviously works.

All-This has been a very helpful and clarifying discussion. I have an ideal situation in that my frame is sitting on axles but has no body on it. It makes it easy to drill and weld, but difficult to flex the suspension and test it. Keep the ideas and mounting options coming.
 
Should the rear shocks be close to 45 degrees from vertical?
They work better when in line with the direction of travel. For crawling these work fine. For desert running/jumping/etc I would suggest as close to vertical as possible. This mounting position (like the one I used) is a decent compromise. It mimics the stock mounting position and allows for more articulation. My traction bar is going to limit my rear droop (not articulation) before my shocks do (imagine picking up the back of the rig evenly so both tires come off the ground at the same time).

PS Notice I'm on my 3rd set of shock mounting bolts through the top of the frame crossmember? 1st is stock, 2nd was first time SOA, 3rd was 2nd SOA with longer shocks and moving the rear end back a few inches (hence the stud going the other direction).
 
I went with Butch Lewis' perches/shock-mounts, I think you can still get them from Mudrak, no welding needed, just bolt in the shock pins that come the RS9000 shocks

butch-built-SO-perches.jpg


rear-disk2.jpg
 
They work better when in line with the direction of travel. For crawling these work fine. For desert running/jumping/etc I would suggest as close to vertical as possible. This mounting position (like the one I used) is a decent compromise. It mimics the stock mounting position and allows for more articulation. My traction bar is going to limit my rear droop (not articulation) before my shocks do (imagine picking up the back of the rig evenly so both tires come off the ground at the same time).

PS Notice I'm on my 3rd set of shock mounting bolts through the top of the frame crossmember? 1st is stock, 2nd was first time SOA, 3rd was 2nd SOA with longer shocks and moving the rear end back a few inches (hence the stud going the other direction).


I'm not sure I would say "better" The shocks will provide more dampening if they are inline with the travel of the two mounting points. But a set of rancho 5000s or a set of 9000s turned up stiff will provide more than enough dampening force.
Mounting at an angle will provide more axle travel for the same amount of shock travel.


Mark...
 
Vitesse-6---Those look like the stock mounts off of a 40. Is that where you sourced them? Something like that could work for me. I have a set off an old FJ40 axle I could cut off and use, or at least try.

IIRC Mine were just like what Trollhole posted in his "how not to do it" pic but with a shock pin welded in where the hole on the lower axle.
IMG_4804.jpg

Sorry, When I had the SOA done(8 yearsago) it was beyond my skills, Still could be, I havent needed to do it again.
Good luck
 
I'm not sure I would say "better" The shocks will provide more dampening if they are inline with the travel of the two mounting points. But a set of rancho 5000s or a set of 9000s turned up stiff will provide more than enough dampening force.
Mounting at an angle will provide more axle travel for the same amount of shock travel.


Mark...
I'd agree.
Just a side note, With my 38.5s it feels as though I am on the edge of not having enough dampening control...especially in the front. It can get a little bouncy at times. Part of this is the tires being heavy bouncy baloons and then only aired up to 4lbs;) My shocks are on the stiffest setting all the time too.
 
Back
Top Bottom