Smog pump bracket

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 9, 2005
Threads
271
Messages
5,828
Location
Cary, NC
Anyone know if the the FJ40 ('78) smog pump bracket is cast iron or steel? I'm thinking of modifying it to use for a GM PS pump, which I'm sure has been done many times before.

If you have done this, pics would be greatly appreciated!
 
Steel...It is easy to modify/drill larger holes into...


Front side of bracket will need to be ground to clear the rib in the pump housing...no biggie.


Here is what I have been running for many years, with the PSC goodies too:
Pump02.webp
Pump03.webp
Pump04.webp
 
Thanks Poser! Seems like you ALWAYS have the answers. Looks like you fabbed a bracket to utilize the stock tensioner arm as well. I think that's what I will do. Now all I have to do is find some hoses.

I don't guess anyone makes adapters so I can use the 8AN fittings on the hoses that came w/ my junkyard pump? I called everywhere in town and people want about $45ea. for the pressure and return lines. Call me crazy, but that seems like a lot.
 
Pressure line with quality hose and fittings will be at least 35.00us....


Return line....you can use fuel line and hose clamps....been doing that for many years.


Good luck!


-Steve
 
The pulley on that pump is a Saginaw press-on style....I *think* that is was off a 1977 Dodge D150 club cab...318V8....I know the original pump and pressure line was from that application...because I owned the truck and parted it out! A couple simple quick bends in the original pressure line and it worked great for years...



:beer:
 
Poser said:
The pulley on that pump is a Saginaw press-on style....I *think* that is was off a 1977 Dodge D150 club cab...318V8....I know the original pump and pressure line was from that application...because I owned the truck and parted it out! A couple simple quick bends in the original pressure line and it worked great for years...



:beer:

does the pulley You have on you pump smaller then all the stock one. be casue I have one but the pulley is way smaller then the stock size pulley (like the chankshaft, water pump) the groove is smaller
 
The power steering pulley uses a 1/2" wide belt, opposed to the 11/16 wide typical Toyota belts...

With that said:


I am running an F water pump on my 1982 2F, with the corresponding F crank pulley and water pump pulley from a late F engine that had smog equipment on it. The alt was on the driver side down low and ran on the inside wide belt, and the air pump was up high on the passenger side, and ran on the outside narrow groove.


There is a Volvo pump and pulley combo that uses the Saginaw pump but is designed to use the wider belt...many have posted up out here about it and how well it works. I have yet to ever see or use one of the Volvo set ups in a Land Cruiser, but I have a couple set aside for me and just have not picked them up yet to mess with them...


:beer:
 
fj40forlife said:
so the one close to the timechain is smaller ?:confused:


The wide belt is on the inside closest to the timing cover, the belt closest to the radiator is the narrow belt.





Land Cruiser F and 2F engines do not have timing chains. The camshaft has a gear on the end that is driven directly off the crank shaft. ;)



:beer:
 
Poser said:
The wide belt is on the inside closest to the timing cover, the belt closest to the radiator is the narrow belt.
Is this just on the F crank and water pump pulleys? My 2F crank and water pump pulleys appear to use the same width belts.
Poser, do you by chance know what the centerline to centerline distance is between the front and rear pulleys on a 2F crank? I did a search and could not find it.
 
bsevans said:
Is this just on the F crank and water pump pulleys? My 2F crank and water pump pulleys appear to use the same width belts.



Poser said:
The power steering pulley uses a 1/2" wide belt, opposed to the 11/16 wide typical Toyota belts...

With that said:


I am running an F water pump on my 1982 2F, with the corresponding F crank pulley and water pump pulley from a late F engine that had smog equipment on it. The alt was on the driver side down low and ran on the inside wide belt, and the air pump was up high on the passenger side, and ran on the outside narrow groove.




Only on the F engines described above...Majority of the F engine set ups ran a single wide belt to the water pump and alt...and were a single wide groove pulley only set up.




bsevans said:
Poser, do you by chance know what the centerline to centerline distance is between the front and rear pulleys on a 2F crank? I did a search and could not find it.



I have not ever seen it in print, but I could grab a pulley and measure it...
 
Correct me if I'm wrong, but the smog pump belt, stock, is 15mm. The closest match I could find is a Volvo 240, which is 12.5mm. Is it OK just to run the narrower belt with this pulley?
 
My experience is that the Volvo pulley isn't not as wide as the Toyota 11/16 pulley, but it is wider than the narrow pulleys used on other Toyota applications. Apparently the Volvo pulley works with the wide belt, as people use them, but I have no personal experience with this. My experience is that the narrow (17/32 inch) belt works fine in the wide Toyota pulleys. You just can't run the same device (like the water pump) simultaneously with narrow and wide belts or one of the belts will wear out fast.
 
Poser said:
I have not ever seen it in print, but I could grab a pulley and measure it...
I'd like to get confirmation of this measurement. I used the double pulley on my mean green alternator to get a preliminary measurement since my crank and water pump pulleys are installed. The double pulley on the alternator appears to have a .875 offset - belt edge to belt edge. The reason I want this measurement is that I'm in the process of getting rid of the GM pulley on my power steering pump and putting a Volvo pulley on to run a stock belt. I do not want to run a front loop of power steering, alternator and crank because the belt length is very long and with a spacer on the air pump can be reduced a number of inches. I am making a spacer to move the air pump pulley to the crank front belt groove so I can have the two following loops. Front belt loop - power steering, air pump, water pump and crank. Rear belt loop - Alternator, water pump and crank. With this setup I can have two belts of the same width over the water pump. I've already machined the spacer and just need to set the length.
Air Pump Pulley Spacer 03.webp
Air Pump Pulley Spacer 05.webp
Air Pump Pulley Spacer 06.webp
 
Poser said:
I will see what I can do when I get back to the shop in the AM.
-Steve
Thanks!
 
Back
Top Bottom