slow cruise control SOLVED !

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 12, 2011
Threads
224
Messages
6,063
Location
Kansas
Does anyone else have a cruise control that doesn't anticipate very well ? I just finished my transfer case re-gear and initially wasn't that impressed when running the hilly section of the local I-70. The truck was still dropping down into 3rd on every hill. Today I paid closer attention to the TP sensor. As I begin up a grade the truck isn't feeding in throttle, it's holding at 26-30%, when it finally does start to add more it is too late and requires a downshift. Then, it stays in 3rd for a lengthy period even after cresting the hill but the TP values drop back towards 26-30 range. If I use my foot and hold the TP around 44% I can cruise up the same grade in 4th gear. I'm curious if anyone else is seeing this.
 
The main input for the cruise control is the vehicle speed, and it only makes adjustments in response to a change in the speed- usually 2 mph before it does anything. By then, the speed has decayed to an unrecoverable point for rigs as underpowered as ours. Hence, the downshift. If you want it to maintain speed without downshifting, make more power.

On the other side of the coin, there's a hill I go down on my way home from work where if left it's own devices, the truck will gain about 10 mph by the bottom of the hill. So, as I crest the top, I hit the OD button and let the cruise modulate the speed in 3rd.
 
It is good to remove and take the cruise control, cable thing out and service it that is gunked up with old grease, by refubishing them with lithium grease
 
If the cruise control cable has excessive slack that could account for "slow" reacting.

Not likely as the cruise control acts as a relay point for the throttle cable and there should only be slack in the cable at idle. At all other times the cable should have tension on it.
 
I tightened the slack in my cruise control cable and while that helped a lot, I still hit the OD button in anticipation of a hill-climb
 
Mine is delayed as well going over the crest of any hill.
 
I have a bit of a lag getting it to hold the speed, I need to clean it and lube it, no problem on hills/mountains, but I may have an advantage :meh:
 
So I adjusted the slack out of the cruise control cable, then ran the truck over the same road, at the same cruise setting. Now instead of seeing TP values hovering around 26%-30% max, the truck will adjust throttle all the way up in the 42%-49% range. Instead of downshifting to 3rd the truck was able to compensate for grade and even accelerate to make up for the 2-3mph it was losing at the start of the hills. I did my entire stretch of I-70 in 4th gear. If your having similar issues with your cruise, you might try adjusting the cable out, it only takes a minute.
 
So I adjusted the slack out of the cruise control cable, then ran the truck over the same road, at the same cruise setting. Now instead of seeing TP values hovering around 26%-30% max, the truck will adjust throttle all the way up in the 42%-49% range. Instead of downshifting to 3rd the truck was able to compensate for grade and even accelerate to make up for the 2-3mph it was losing at the start of the hills. I did my entire stretch of I-70 in 4th gear. If your having similar issues with your cruise, you might try adjusting the cable out, it only takes a minute.

Is this adjustment done at the throttle body?
 
So I adjusted the slack out of the cruise control cable, then ran the truck over the same road, at the same cruise setting. Now instead of seeing TP values hovering around 26%-30% max, the truck will adjust throttle all the way up in the 42%-49% range. Instead of downshifting to 3rd the truck was able to compensate for grade and even accelerate to make up for the 2-3mph it was losing at the start of the hills. I did my entire stretch of I-70 in 4th gear. If your having similar issues with your cruise, you might try adjusting the cable out, it only takes a minute.

Wow, nice find dude. So the CC cable is more taught vs slack from before? This is interesting as I thought this cable should have a little bit of slack in it.
 
Is this adjustment done at the throttle body?

Yes, right next to the throttle cable, and just above the kickdown cable.

Wow, nice find dude. So the CC cable is more taught vs slack from before? This is interesting as I thought this cable should have a little bit of slack in it.

Correct, mine had a lot of slack in it. My reasoning was that if the cruise is trying to pull on that cable, and it has to take up slack first, it might be throwing it off. It's little computer brain would be thinking it was adding throttle when all it was really doing was pulling slack. That may or may not be what was happening, but it definitely fixed the issue for me.
 
Yes, right next to the throttle cable, and just above the kickdown cable.



Correct, mine had a lot of slack in it. My reasoning was that if the cruise is trying to pull on that cable, and it has to take up slack first, it might be throwing it off. It's little computer brain would be thinking it was adding throttle when all it was really doing was pulling slack. That may or may not be what was happening, but it definitely fixed the issue for me.

Makes sense to me. There's a couple of things about this in the FSM but here is what most directly relates to what you posted about:

upload_2018-7-25_16-6-54.webp
 
Makes sense to me. There's a couple of things about this in the FSM but here is what most directly relates to what you posted about:

View attachment 1752522

I'd say my freeplay is definitely less than 10mm now. Probably less than 2 actually. I got it just on the other side of snug, so it's not quite pulling on the bell crank but there is almost no slack.
 
I'd say my freeplay is definitely less than 10mm now. Probably less than 2 actually. I got it just on the other side of snug, so it's not quite pulling on the bell crank but there is almost no slack.

From what rockstate posted, I'll bet that's not an issue as long as your idle is still normal; i.e., your throttle plate is still closing completely.

Nice job on the fix. :beer:
 
Back
Top Bottom