Sliders welded or clamped?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 7, 2016
Threads
176
Messages
939
Location
Decatur GA
I am about to build some sliders and all the ones I see clamp on. Is there any reason for this other than most people cannot weld? I am a welder and I would have no problem welding mine to the frame, but I wanted some feedback on whether or not that might be a bad idea? The only reason I could see needing to take them off is if it got so bent it got in the way. But that could happen to any part of the truck.
 
I have mine welded on and the only complaint I have is that I need a 1" body lift so they're not so tight to the body. It would be nice to go back and cut them off and sleeve them inside to make them remove able in the middle or something.
 
Mine are bolted on and have had no issues.
 
I have mine welded on and the only complaint I have is that I need a 1" body lift so they're not so tight to the body. It would be nice to go back and cut them off and sleeve them inside to make them remove able in the middle or something.

I wonder if welding in some 1-2" receiver hitches could solve that problem. Cut through the frame and weld in three receivers. Three pins and they are off. A lot of work though.
 
I wonder if welding in some 1-2" receiver hitches could solve that problem. Cut through the frame and weld in three receivers. Three pins and they are off. A lot of work though.
Yeah, that and rattling noise and drives me up the wall, I won't even drive around with the stinger in my toe receiver unless it's towing something. I was thinking just cutting the legs in the middle and using some DOM the size of the slider legs ID and plug weld them in on the frame side of the leg and drilling them for a pin on the slider side or vise versa. That way they're a tight rattle free fit and can be removed whenever neccessary, the only reason I see to remove them it to facilitate repainting really.
 
IMG_3686.webp
I have the driver side welded in and made the passenger side bolt on to make messing with the exhaust easier. I welded some 3/8" plate to the frame with tapped holes in it to give me something to bold to instead of the clamp method. :meh:
 
I've heard some people claim that welding on the frame could raise issues with the frame becoming brittle or crystallizing. I had welded on sliders when I owned a Blazer, and had no issues. I have bolted on sliders on my Cruiser, because that is what was most reasonably priced.
 
My sliders cost less than $200 for materials and consumables.

RuSAiI7CZyOohOYlk_7S4DcxvcrzRfF1G69AWuSZsO8zlgEDuFUp8VNA_Ypb_58WFVhao_NqMPWKG30_GBdcDhWW-xFGwYKMlasCnf053yyqT9S_Tt1zzMBKrYs7TcyjefBlbbTKM_l8lagX0HbE6anMewtAFZQetm5UDiRFdTvuIH63VpMc5TYgJqZYuSIXda8HcLk_LuNLOkB6K9AjwvYkbUFwx9SHTotjPpzvS5PIGTMmOe3sYHHMx0FKH8kTaJtQOTl8mkwU0TIGXngdYsj8w6d_Bsfi1j7hJ8lZXTAQoZnDCBB5O3UPxGjnFRPOUc8w7dtUYBqdJ0o8TOvOjpMV9GpbN4a9Y9PIIQx1zAys96HqawDV3IqGXAXwK9HnVGHh_ZHpAPQvj97olYT4AulWsa0Qqz-MaIkSX24i8ebx8UB4rh_MI0pMST9z6cKEj_nmrqSVYLfPIS8ybrpWKlFqfJPgpUjyVHeFFfxuVSkZ53n2EHmErQ-TdgwkUQSPpy0RCrRYA3sXcWiQRr1-Zq92yjO0Wa6cjbXSm9BpoFfUj82DPaxFjiu0DRkmXr1HOR4-m-ymrYBNWULTNuRXHrWQ0RuR8mCuLuBoO6FMoFhZnYqB=w750-h422-no

WdKslb-5GTNpMgHVXQO04MVF6HJQp-yk-F0FPYvSAp9ibomqHkRMaFiUNKyolgxUiIMHntu61ihspuUU5-q-vtve0k5xmBdkrO8kI_qcMW-kTWl1u-DpkigbYuY2i5d4MdmRb9zpXcZycKWUdUoikDRSjTzM3Q5OQWwh-kxnl1Kw6o623rt4cYmfN2nAYK558HdB6fDdcGAOmWRtgRIqk9LPsvUASUYMNdixypy2dYQfoldhCr_lzzDlw7Vxe5BxVzuWXtwnlRGWEWjVoSmXqIn9A7zk02CUlqONRI6ykjpBX0oZXv0bDOvIJwICmN74N09UsegYGxz73Gu4LIRoP5D50DnYL53-X-a7Ittbta4vO2ZY6OHPtV7yKtHUMFGNhTgTrycgM_ljUaoQmnhSGr5UMwgXjhDNd9Tc73WUNmADe8lCOOAnrhWbIdroifsGbqFvoAzjNI2UudQrI-58U3AGqtGIXvj03WSTvOhM5aaaEEaY5cd5Me4ij0UdrGS-2Q0fTtD4gojAPKGex2ogauGIsWNWm6Et0DXTE0Mo1qziCai78p1-tphjpIZVPqQCEFsVR__tCC8YT8naXgbWQUKkNg4-X_y4CuBkRCov-X8Drfy0=w666-h1182-no

SaPcrE3M1QQ3_Y_oDPEGpknuxHdxqIifdV0QEZz_v3Z5yXJZ_lnUAj2QppH_f9lGdOMQkC_L_pmWbVw897V288QPhrZf9cdBe7TBwACsogdkLs3Fdcy98iOcAo0eVQyxG31O_vJBPfpFyUUk-Mu4BZXOpYTzXIQBoQS63flog0knwQFPyLN3KGpH4jq9-v1vRtBdfesR_5ywQER3p925gPAheYTcnEYg68YU4FHVzIMRxgYwq4xGlh8GZCAP2tdEiYIadud_0aiijJB4WUQxZLozCIQVaq2Kugt6RAR1-jeCofaaMBS0HdyNOuy_1VBXn8S_DKepBWxYdZMWDrsTwqrronZ07nT3sOCp7n0ikWBkkUZAY3tSzH_b2coIO55OUYepavEJ1CnOPBgHPA7Gp1H4EHIvVOUkGPoGMbvLM6vjkJGgB7zQ_dV08wF0l5rwU5BbbNjdhViekwS39RP63cSnDYQx6FgFOtZZYcO-Z-FNJkiGrHJNjKWR3RlzmQyH4UgN0grI5DGvMDbHVqvke6-bVpd64xFKUIFBgegLxe_CFat2pXm2CILoIBdmwHUbr9geFCTsQlJMphNBCEEwq2RJNtxo3ids8X9MHv1JuWAkHaCH=w666-h1182-no
 
2" x 2" x 3/16" square tube ~ 12'
1.75" X .120 DOM round tube ~ 16'

I purchased 20' sticks of both and just used what I needed. I also used 1/4" plate for gussets and mounting plates on the passenger side slider.
 
When I made sliders for my truck I bolted them on so that way if I ever need to remove them I'm not sitting there showering myself in sparks to remove them.
 
Some counties will not allow welding to chassis members as it may affect the strength of the steel.
Also if they are welded on and get damaged it is harder (maybe) to repair them.

Mine are clamped on and were made from a pattern found on the web. Took me a couple of weekends of cutting, grinding and welding to get them made and a couple of days to get some custom U bolts to fit them. Had to of them when I went to a 3" exhaust but it wasn't to hard.
Seem to recall that they were designed by George Scolaro and were for the petrol engined cruiser.
 
I wonder if welding in some 1-2" receiver hitches could solve that problem. Cut through the frame and weld in three receivers. Three pins and they are off. A lot of work though.
I wouldn't cut through the frame. Surface welding is plenty strong. If you plan to wheel it and slam your sliders on rocks with a rig this heavy, I'd rather have my welds be the weak link than the frame itself. 80 frames along with most Toyota frames are way over engineered and boxed but are engineered to flex. Cutting and inserting a heavy ridged piece of steel will create unnecessary stress when the frame tries to flex. All spring buckets and link mounts are welded on the frame along with the top and bottom of the frame itself from the factory so I wouldn't worry about welding. Just make sure you don't weld too much in one area at one time and your welds don't cool too fast.

I've been building rock crawlers and bagged trucks for a long time and I've never seen a frame crack from weld ons. Only when the frame was cut for a c notch, bag plates or air bumps have I seen cracks. With the frame cut and welded it usually cracks at the weld then bends from lack of support at which point you're pretty much screwed unless you're good friends with a frame guy.
 
My sliders cost less than $200 for materials and consumables.

RuSAiI7CZyOohOYlk_7S4DcxvcrzRfF1G69AWuSZsO8zlgEDuFUp8VNA_Ypb_58WFVhao_NqMPWKG30_GBdcDhWW-xFGwYKMlasCnf053yyqT9S_Tt1zzMBKrYs7TcyjefBlbbTKM_l8lagX0HbE6anMewtAFZQetm5UDiRFdTvuIH63VpMc5TYgJqZYuSIXda8HcLk_LuNLOkB6K9AjwvYkbUFwx9SHTotjPpzvS5PIGTMmOe3sYHHMx0FKH8kTaJtQOTl8mkwU0TIGXngdYsj8w6d_Bsfi1j7hJ8lZXTAQoZnDCBB5O3UPxGjnFRPOUc8w7dtUYBqdJ0o8TOvOjpMV9GpbN4a9Y9PIIQx1zAys96HqawDV3IqGXAXwK9HnVGHh_ZHpAPQvj97olYT4AulWsa0Qqz-MaIkSX24i8ebx8UB4rh_MI0pMST9z6cKEj_nmrqSVYLfPIS8ybrpWKlFqfJPgpUjyVHeFFfxuVSkZ53n2EHmErQ-TdgwkUQSPpy0RCrRYA3sXcWiQRr1-Zq92yjO0Wa6cjbXSm9BpoFfUj82DPaxFjiu0DRkmXr1HOR4-m-ymrYBNWULTNuRXHrWQ0RuR8mCuLuBoO6FMoFhZnYqB=w750-h422-no

WdKslb-5GTNpMgHVXQO04MVF6HJQp-yk-F0FPYvSAp9ibomqHkRMaFiUNKyolgxUiIMHntu61ihspuUU5-q-vtve0k5xmBdkrO8kI_qcMW-kTWl1u-DpkigbYuY2i5d4MdmRb9zpXcZycKWUdUoikDRSjTzM3Q5OQWwh-kxnl1Kw6o623rt4cYmfN2nAYK558HdB6fDdcGAOmWRtgRIqk9LPsvUASUYMNdixypy2dYQfoldhCr_lzzDlw7Vxe5BxVzuWXtwnlRGWEWjVoSmXqIn9A7zk02CUlqONRI6ykjpBX0oZXv0bDOvIJwICmN74N09UsegYGxz73Gu4LIRoP5D50DnYL53-X-a7Ittbta4vO2ZY6OHPtV7yKtHUMFGNhTgTrycgM_ljUaoQmnhSGr5UMwgXjhDNd9Tc73WUNmADe8lCOOAnrhWbIdroifsGbqFvoAzjNI2UudQrI-58U3AGqtGIXvj03WSTvOhM5aaaEEaY5cd5Me4ij0UdrGS-2Q0fTtD4gojAPKGex2ogauGIsWNWm6Et0DXTE0Mo1qziCai78p1-tphjpIZVPqQCEFsVR__tCC8YT8naXgbWQUKkNg4-X_y4CuBkRCov-X8Drfy0=w666-h1182-no

SaPcrE3M1QQ3_Y_oDPEGpknuxHdxqIifdV0QEZz_v3Z5yXJZ_lnUAj2QppH_f9lGdOMQkC_L_pmWbVw897V288QPhrZf9cdBe7TBwACsogdkLs3Fdcy98iOcAo0eVQyxG31O_vJBPfpFyUUk-Mu4BZXOpYTzXIQBoQS63flog0knwQFPyLN3KGpH4jq9-v1vRtBdfesR_5ywQER3p925gPAheYTcnEYg68YU4FHVzIMRxgYwq4xGlh8GZCAP2tdEiYIadud_0aiijJB4WUQxZLozCIQVaq2Kugt6RAR1-jeCofaaMBS0HdyNOuy_1VBXn8S_DKepBWxYdZMWDrsTwqrronZ07nT3sOCp7n0ikWBkkUZAY3tSzH_b2coIO55OUYepavEJ1CnOPBgHPA7Gp1H4EHIvVOUkGPoGMbvLM6vjkJGgB7zQ_dV08wF0l5rwU5BbbNjdhViekwS39RP63cSnDYQx6FgFOtZZYcO-Z-FNJkiGrHJNjKWR3RlzmQyH4UgN0grI5DGvMDbHVqvke6-bVpd64xFKUIFBgegLxe_CFat2pXm2CILoIBdmwHUbr9geFCTsQlJMphNBCEEwq2RJNtxo3ids8X9MHv1JuWAkHaCH=w666-h1182-no
Thanks for the pics I'm getting ready to build mine, had the same design in mind, seeing pics will save me some time. I'm back and forth on round or square tube for the inside rail.

I can't get over what the aftermarket guys are getting for these! And they flare out at the back doors, major catch point. The idea is to slide the body into the back tire not away from it. The only ones I like from the bolt on options are the rectangular tube step sliders to keep it looking stock. I opted out of that design for more clearance and protection of my doors. I'm staying as low as possible with 35s or 37s haven't made up my mind yet. Though this rig won't see the Fordyce creek, it's just too pretty to damage on an easier trail like the Rubicon.

What lift are you running?
 
Thanks for the pics I'm getting ready to build mine, had the same design in mind, seeing pics will save me some time. I'm back and forth on round or square tube for the inside rail.

I can't get over what the aftermarket guys are getting for these! And they flare out at the back doors, major catch point. The idea is to slide the body into the back tire not away from it. The only ones I like from the bolt on options are the rectangular tube step sliders to keep it looking stock. I opted out of that design for more clearance and protection of my doors. I'm staying as low as possible with 35s or 37s haven't made up my mind yet. Though this rig won't see the Fordyce creek, it's just too pretty to damage on an easier trail like the Rubicon.

What lift are you running?
Slide the rock from the body to the back tore
 
I'm not a fan of bolt on sliders. Both of my 80s have sliders welded to the frame. On the LX450 we made a removable plate that protects the cat and adds additional support to the front of the passenger side slider.

There is no issue welding to the frame of an 80 Series. As stated earlier, everything is welded to the frame at Araco when they're built.
 
I did a combination of a weld on plate and two clamps on each side. I think having them removable is a smart idea for many reasons.
 
Thanks for the pics I'm getting ready to build mine, had the same design in mind, seeing pics will save me some time. I'm back and forth on round or square tube for the inside rail.

I can't get over what the aftermarket guys are getting for these! And they flare out at the back doors, major catch point. The idea is to slide the body into the back tire not away from it. The only ones I like from the bolt on options are the rectangular tube step sliders to keep it looking stock. I opted out of that design for more clearance and protection of my doors. I'm staying as low as possible with 35s or 37s haven't made up my mind yet. Though this rig won't see the Fordyce creek, it's just too pretty to damage on an easier trail like the Rubicon.

What lift are you running?
OME heavies with a 25mm spacer in the front. More details in signature.
 
If you can catch you trail gear sliders on sale, you pay about the same as mentioned above, are weld on and if you don't have notching or coping equipment, saves you a lot of headaches.
 
Back
Top Bottom