Rolled my truck

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 7, 2004
Threads
100
Messages
2,589
Just too much speed. Stupidity. But I got lucky. slid off the crack onto pass side softly. crushed the front fender. But both doors are untouched. real small kiss on the rear quarter just behind the rear door. the rear of the truck was completely supported on the rear quarter protector I fabbed onto my bumper and on my wide sliders. I was so lucky. The front fender wont need to be replaced as I will be cutting off the disseased part for the upgrade....

The front end is too stiff as we all know. It unloads violently. I have been preparing for the 3 link but I want bigger tires and more confidence in my axles. I want to be able to bounce and spin 38-40" meats recklessly without holding my breath. Longfields are nice but what of the housing and small R&P? Have decided on a 5:13 chevy d60 w/ 35spline outers and ARB locker. Will 3 link.

Was thinking of keeping the 32 spline FF toyota rear but as It needs a regear anyway I'm going to ditch it for a good old 5"13 14b with detroit

Will keep the 4" springs and cut the fenders up. Staying low. Hydro assist unlikely for now. needs a cage inside but that will be later

I wish there was a t-case option but their is not as of now. With 38" swampers I will be ok.

I have already have almost new 38" swamper bias plies and some of the rubicon express joints. Considering reusing the rear links as the rear works so well already
Bald Mountain Nov 07 (4).webp
Bald Mountain Nov 07 (6).webp
CIMG3936.webp
 
Glad your ok and the damage was minimal. Other roll overs on the board unfortunately haven't faired so well...
 
Is that a Jeep pulling?
 
Is that a Jeep pulling?

me pops jeep. we straped his rear bumper to a tree and then winched my truck till all 4 wheels were touching the rock and I drove in reverse while sideways. my truck didn't mind being sideways-she ran smooth as ever

This was bald mountain by the way. We finished wheeling the day away
 
Wow - bet you're feeling pretty good about that protection system about now. From the looks of things, you had the right protection at the right time. Much harder and the protection wouldn't have made as much difference, much lighter and you would not have needed it. Very nice!!

DougM
 
The sliders and rear quarter guards saved my bacon. The front hoops I started and havn't got to tieing them together yet. If I had I could have walked away unharmed. But as the pass hoop wasn't tied in it was more of a damage multiplier

Wow - bet you're feeling pretty good about that protection system about now. From the looks of things, you had the right protection at the right time. Much harder and the protection wouldn't have made as much difference, much lighter and you would not have needed it. Very nice!!

DougM
 
Wow! I'm starting to get more and more nervouse that my time is coming.

I am really surprised that your rear bumper side protection held. I would have bet my paycheck that it would have flexed into the body.

Glad you and the truck are mostly OK.
 
Glad you and the cruiser are ok.

But sorry man, that's not a roll. That's a flop. Rolls involve the roof touching flat ground at some point during the experience ;p You're not quite as cool as beno and PKP80 yet :flipoff2:
 
Doesn't count if you aren't on the roof! :)

Glad everyone is okay...I have rolled my truck if that counts...but I drove out of it!
 
Someone give that man a gold star. bout the best you could do for goin over it seems. So where is the i rolled my 80 thread? e_parise is lookin for axles https://forum.ih8mud.com/showthread.php?t=187816
lookin forward to dusty's 80 v 2.0
 
Glad you are Ok dude .. and the 80 .. wel some bits and nothign really to worry ! it run and it's a Land Cruiser ..
 
The front end is too stiff as we all know. It unloads violently. I have been preparing for the 3 link but I want bigger tires and more confidence in my axles. I want to be able to bounce and spin 38-40" meats recklessly without holding my breath. Longfields are nice but what of the housing and small R&P? Have decided on a 5:13 chevy d60 w/ 35spline outers and ARB locker. Will 3 link.

Amazingly little damage for a flop, great to see your protection held up. The unloading issue isn't because of stiffness, it is a characteristic of radius arm suspensions, although even a 3-link will see it.

Design a limiting strap into your 3-link so the bottom can't drop out. These can be easily designed to allow full desired flex on the corners with only about 3" of allowable drop of the entire axle.

The D60's will be sweet, I think once you get out of the box full axle upgrades make all the sense in the world. You can start from scratch with your links with pretty much bomb proof components. Keep us posted on the build.
 
Back
Top Bottom