Resolved - Diff issue, Oakley KS - any resources?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Hey guys, this is super helpful. Thank you all. I'm no mechanic, but the descriptions are pretty clear and it's making sense to me. I'm hopeful that when I engage the shop with this path that it will gain traction and we'll pull out of this mess (all puns intended).

Hopeful we'll learn "it's only the front wheel drivetrain" and we can disconnect it and continue on with repairs at home later. I'll post back here with either resolution or more questions. Again, thank you all for your input up to this point.
 
Also, if for some reason the failure is related to the snap ring failing to hold the front axle in the hub flange, a trip to Lowes or Home Depot and $5 in parts can get you a rugged bodge fix until you get to Denver. You will end up needing an axle long-term, but to get back on the road again, the current axle can be used.

You'd buy the following:

PVC 1.25" to 1" reducer or 1.5" to 1.25" reducer (I can't remember the exact size)
Set of M8 x 1.25 bolts that are 3/4" long and longer
1 of each of every metal flat washer size you can find, starting from smallest that fits over the M8 bolt to the biggest that is sold that fits on the lip of the PVC piece
Blue Loctite


Stack the washers on the right sized bolt, and ensure the end of the bolt sticks out just a bit on the other end of the PVC reducer pipe. The thick side of the reducer pipe will sit against the hub flange, and it should sit on the lip where the grease cap snugs against the hub flange. Put a bit of Loctite on the end of the bolt, then thread into the end of the axle. Tighten (with caution!) the bolt until it is snug and the washers can't slide around easily. If you overtighten, the bolt will shear/pop and you'll then have to remove the rest of the bolt body from the axle threads, so be very careful.

This little gem is rotationally symmetric around the axle, so it can withstand speed and be used on the highway. It is also lightweight so the wheel balance is not affected too badly.

(For those of you worrying about failures on the road or trail, the parts in bold make an excellent addition to your emergency parts and tools kit)
 
^this repair is for the scenario of a missing snap ring, to keep the axle shaft from migrating inward as it's driven - correct?
 
^ Correct, although the parts I mentioned above are better suited to the job than the bodge I created at that time.
 
Seems you could just drill a hole in the dust cap, use a longer than normal bolt and achieve the same thing. Order a new dust cap to replace that one (at your leisure) keep the old one for emergencies.
 
Seems you could just drill a hole in the dust cap, use a longer than normal bolt and achieve the same thing. Order a new dust cap to replace that one (at your leisure) keep the old one for emergencies.
Those dust caps are pretty flimsy. It would likely cave in.
 
Seems you could just drill a hole in the dust cap, use a longer than normal bolt and achieve the same thing. Order a new dust cap to replace that one (at your leisure) keep the old one for emergencies.
It may work for a bit, but the surface is crowned and you'd have to be pretty precise in terms of centering the hole for the M8 bolt. Miss the mark and it could be a problem since the dust cap has no slop for movement.

I'm not sure how many folks carry a cordless drill around in their rigs; I don't. I try to keep the Superleggera concept as true as possible (!!)
 
Well, the shop got to look at it and advised catastrophic transmission failure. Rather than deal with such a repair from 550 miles away, I'm going to pick it up with a flatbed trailer to bring it home and go from there. Thanks all for your assistance.
 
Did they give any justification for that conclusion??
 
Did they give any justification for that conclusion??
Some noise in tranny in both neutral and park. Lots of metal noise in drive. Transfer case in neutral and still makes all the noise. The noise apparently is coming from the tranny. Did not disassemble it, but did this on the rack. Will not drive in forward or reverse.

From what little I know, this would be an unusual failure. Tranny fluid was checked and fine. I DID have tranny "scheduled" service in the last six months by reputable local shop. Again, the fluids appeared ok.
 
I think the naughtnaughts (00s) did suffer from some tranny failures. It has been discussed in this forum a few times. Maybe your son's number just finally came up on the roulette wheel of transmission death ....
 
I think the naughtnaughts (00s) did suffer from some tranny failures. It has been discussed in this forum a few times. Maybe your son's number just finally came up on the roulette wheel of transmission death ....
Sounds like this may be the case. I had a 2003 and just never heard of it being "a thing", although certainly I didn't spend a bunch time seeking out that info since I didn't have any problems.
 
Those dust caps are pretty flimsy. It would likely cave in.

Knocked the heck out of new ones with a 2lb brass hammer to get them to go on. Didn't cave them in, so I don't know if I agree with that.

IF a person is only 'holding' the axle in place and not having to 'draw' it forcefully against damaged/galled splines then it should work fine.

I have my old caps someplace, I'll just give it a try when I get time.
 
It may work for a bit, but the surface is crowned and you'd have to be pretty precise in terms of centering the hole for the M8 bolt. Miss the mark and it could be a problem since the dust cap has no slop for movement.

Clearly you would drill a hole somewhat larger than needed, I promise you....I could do this.

I'm not sure how many folks carry a cordless drill around in their rigs; I don't. I try to keep the Superleggera concept as true as possible (!!)

The same number of folks that carry the items you suggested. ;)

In either case it would be wise to have the items 'on hand' in your emergency kit....whichever method you choose.

In most situations....I'd wager I could find someone with a drill faster than I could find a ride to the nearest hardware store, but who knows.

Bottom line: Try to be prepared for those little things that can leave you stranded. (within reason).

Good discussion and food for thought.

Sorry to hear the outcome of the OP's issue.
 
Sorry the late reply @94SRUNNER. Land Cruiser update is that I drove from NWArkansas to Colby KS and back with a flatbed trailer and picked up the rig and my son. Long day for an out-and-back. I considered leaving my son there but I believe he had seen all there was to see in Colby KS. (totally kidding...)

Dropped off the Cruiser at my local transmission shop that had recently served me well for my 2012 Suburban. Four weeks and several $$$$ later we finally got the Cruiser back with it's transmission rebuilt.

While dropping off the Cruiser at the shop and then stowing the slide-in ramps on the trailer, I tore my bicep tendon on my right / dominant arm. I felt / heard it pop, and may have said some unruly words. I had that injury repaired about 10 days later and just got out of the cast earlier this week. Will be in a brace and then PT for a total of about 4 months.

Expensive but hopefully educational adventure trip to West Kansas (in lieu of the silly idea of spending some time in CO).

Unrelated to Cruiser, but occurring at the same time: garage door opener went out at the house that day, too. $ repair and then a $$$ replacement about a week later.
 
Sorry the late reply @94SRUNNER. Land Cruiser update is that I drove from NWArkansas to Colby KS and back with a flatbed trailer and picked up the rig and my son. Long day for an out-and-back. I considered leaving my son there but I believe he had seen all there was to see in Colby KS. (totally kidding...)

Dropped off the Cruiser at my local transmission shop that had recently served me well for my 2012 Suburban. Four weeks and several $$$$ later we finally got the Cruiser back with it's transmission rebuilt.

While dropping off the Cruiser at the shop and then stowing the slide-in ramps on the trailer, I tore my bicep tendon on my right / dominant arm. I felt / heard it pop, and may have said some unruly words. I had that injury repaired about 10 days later and just got out of the cast earlier this week. Will be in a brace and then PT for a total of about 4 months.

Expensive but hopefully educational adventure trip to West Kansas (in lieu of the silly idea of spending some time in CO).

Unrelated to Cruiser, but occurring at the same time: garage door opener went out at the house that day, too. $ repair and then a $$$ replacement about a week later.

Sorry to hear about the injury @DustyBrands! I hope your recovery goes smoothly.

Glad the Cruiser is back on the road!
 
Well, sure sounds like you’ll end 2021 healthier and wealthier than you started it, so just look forward to that!

Sorry to hear about the tough luck but glad all is sorted and in the rear-view. Friend of mine in college on the wrestling team tore his bicep and it curled up into his shoulder... wouldn’t wish that on anyone.
 
Back
Top Bottom