Rear passenger side wheel

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 12, 2006
Threads
1
Messages
2
Hi Everyone,
I recently found out what a Land Cruiser was and caught the bug instantly. I am looking to buy something from 1976-1986. A guy near my home has a 1976 FJ40 for sale. There is one thing about it that I am concerned about.
Basically the rear passenger side wheel sticks out about 2 inches more on that side relative to the wheel wells than it does on the drivers side. This is with all four wheels on level ground and pointing straight ahead. The wheels and rims are exactly the same so its not that. The folks on cool cruisers of texas had some good ideas and one person said this is a great community to get info and ideas on cruisers so here I am posting my question over here.
Please chime in with your ideas and thoughts. It just doesnt seem natural. The owner states that is normal, but he bought it 10 years ago and doesnt know what happened to it over its first 20 years.
Thanks,
Steve
 
Steve-

Welcome to mud and the addiction! 76 is a good year to go for, IMHO, 76 to 78 are the best all around years, with the 78 being tops... I have a 76. They stopped selling the fj40 around 83ish here stateside.

A picture would really really help here, but without it here goes:

1. make sure the wheel in questions backspacing is the same as the others. The wheel may be the same style but if it has a different backspacing then the tire/wheel can protrude out farther than the others. Measure from the outside of the wheel rim to the inside of the "dish" on the wheel. If you get three the same and one different this is your problem.

2. Make sure the axle isn't somehow sliding out of the housing. I am not sure if this can be done or not, but the axle on a 76 slides in and out of the housing and it is fastened inside the differential with a C-clip. Jack the truck up and see if you can slide the whole wheel in and out. If you can this is your problem.

3. Make sure the tires are all the same width, oversized tires can hang out past the wheel well openings, even if they appear to be the same manufacture and type of tire, they can run in different widths.

4. Check the frame and spring packs and make sure they are all still lined up correctly, if the frame is jacked up you could get an issue like you are describing.

Post up a few pics and we can help a lot more, what's the asking price? and where are you at? Someone may be willing to help you look at it.

Good luck

Rezarf <><
 
i would measure the backspacing as well. or look for a spacer, very odd.

ask the seller wtf is up with this wheel, he should know.
 
pics of the cruiser with rear passenger wheel

Here are the best pics i have showing the two rear wheels. A straight on shot from the back would show it best but i didnt have one. The pics arent the best but I included one of the drivers side that shows that the tire is pretty much flush with the body.

The cruiser is in Mesa, AZ and he first told me he wanted $5-6000 for it. I had done a fair amount of investigation to get a feel for a reasonable price ahead of time and that was about twice what I came up with. I need to sort out this rear wheel thing before I actually give him an offer if I do at all. I really appreciate everyones help.

Its the original engine and has 150,000 on it. He bought the top separately but someone cut a 12-16 inch square hole in the top for a roof vent pretty which does little to help the value of the deal.

The vehicle needs a lot of love, but new seats, restore the roof and a new paint job would do wonders. I found another contact that says he can set me up with a few friends that have Cruisers in Arizona that I could get for $2500-3000 and that may end up being the route I take, If I cant sort out this rear wheel thing. For now I am pursuing this one and my curious side "needs" to know what is up with this wheel even if i dont buy it.

Thanks Everyone!
Steve
PA060004.webp
PA060008.webp
PA060009.webp
 
Your research would be correct; that is not a $5-6000 Cruiser. It looks to be a collection of parts from many Cruisers. It does appear to have a solid, mostly rust free body though.
 
The windshield frame and hard top are not from the same vehicle as the tub, but I'm not so sure I'd go so far to say that it's a Franken-cruiser. I agree with Coolerman's valuation, though.

The replacement windshield frame (on a fairly non-rusty cruiser) and the potentially off-set axle would make me try to find out when it was rolled, how bad, and who fixed it. But the body doesn't show signs of a roll. Huh.
 
I worked on a cruiser once that someone had installed a centered rear differential... to ease the angle of the drive line.. they cut the spring perches, pushed the differential as far to the right as possible and welded the perches back on.. it worked out OK.. they didn't mind that the right side stuck-out farther.. it was just a ranch truck...
 
Back
Top Bottom