Radiator BLEW UP!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Shahram said:
Bent the hood, so that it sits an inch above the left quarter panel when down.

Check with PHAEDRUS on this. He has mentioned several times that some collateral damage is covered by your comprehensive insurance. You might get lucky, and my friend, it sounds like you could use a little good luck about now. :cheers:

-B-
 
thats violent..........Is this common for these plastic topped rad's?

I had a battery blow in my garage one time, embeded in the cieling and broke the light (hood was open). Plus it was LOUD!
 
Man I will add to the masses and say WTF!! I have never seen a radiator fail like that. Sorry to hear but glad that you got it off the road and shut down before even more damage could occur.

:cheers:
 
The top tanks get damaged from mechanics resting knees and elbows on them, then fail. Boiling water obviously has a lot of force, and it may be a leak allowed air in the system. A full system can go way above the boiling point as pressure prevents the expansion effect of boiling. But if it had gotten air in it, then the system wasn't under enough pressure to prevent boiling. When the water is circulating fast at freeway speeds/RPM, it is more uniform in temp than idling, etc, which means a large amount of it got to the boiling point simultaneously - a formula for the big one!

Point of interest. I should be receiving a bunch o' parts from Dan tomorrow and among them is an O ring set for the radiator top/bottom tanks. I have a couple here and plan to open them up and put new O rings in to see if it can successfully be done. Then I'll have them pressure tested by a rad shop. Leaking O rings cause the slight air in the system for a lot of us, in my opinion. I'll let you know how it goes.

Shahram, I'll be curious how much/any sludge in your core?? Course it just got steam cleaned, but...

DougM
 
This isn't an uncommon problem. A search finds these instances. It would be nice if the actual cause could be determined. Belt failure that whacks the top of the radiator? Pressure build-up? Something else? :confused:

I'm paranoid now that my radiator is going to blow. :crybaby:

Tom



https://forum.ih8mud.com/showthread.php?t=82619&highlight=radiator+blow

https://forum.ih8mud.com/showthread.php?t=46712&highlight=radiator+blow

https://forum.ih8mud.com/showthread.php?t=106160&highlight=radiator+explode

https://forum.ih8mud.com/showthread.php?t=53225&highlight=radiator+explode

https://forum.ih8mud.com/showthread.php?t=45833&highlight=radiator+explode
 
Well the postive thing about this, like you said is that it happened on a local freeway. I'm glad you came out okay. Time to spend the suspension money on a good rad, and all the little extras. Question, do you think the RT temp. gauge mod would have helped you in this instance?
 
Might also have your HG checked, Exhaust into the water jacket can do that. Radiator pieces could have taken out your belts after the fact.....
FWIW,
Dan
 
That sucks. Mine went abou a month ago the day after I got back from scout camp. At least it didn't happen with a bunch of 12 year olds in the truck. Cruiser Dan set me up with all new belts, hoses, thermostat, fan clutch and radiator at a very reasonable price.

My hood did the same thing. I modified the latch by elongating the mounting holes and now it sits level. It still wobbles a bit though.:crybaby:
radiator.webp
radiator.webp
 
If your hood wobbles, be advised the hood stops are adjustable so you might be able to crank them up against the hood's new position. Also Haddock - looks like your radiator was either nonstock or had been recored.

DougM
 
I have them adjusted almost to the point that they are going to fall out. Maybe I can replace the threads with longer pieces. When the radiator popped, it must have bent the hood just enough to screw up the fit. I can't see or feel where it's bent. I'm still tweaking it. Thanks though.

How can you tell the radiator is aftermarket?

Here is a better pic:

radiator 2.webp
radiator 2.webp
 
The temp guage mod needs an addition- an electrical contact on the needle that will illuminate a warning light whenever the temp rises above 'x'. I look at my guage all the time, but I know it will start to rise right after I glance at it, and it only takes a few seconds...

-Spike
 
major bummer dude.

I swapped out my radiator a couple months ago. It's not a terribly difficult job, just time-consuming. It took me a full day to do the swap.

I replaced the thermostat, all hoses, belts and fan clutch at the same time...figured I was in there anyhow...

I don't know what kind of time you have...but it might save you mucho burrito money if you DIY it.

I got all my parts from CDan...I bought the 93-94 radiator, rather than the one for the 97 model year.



What lift are you temporarily delaying? OME?
 
NorCalDoug said:
What lift are you temporarily delaying? OME?

Yeah, an OME 2.5" Med./Heavy. Little thank you to me for scoring a good-sized contract commission. No problem though, it can wait...coulda been worse, and it's not like I'm not already pleased with the off-road handling of my stock suspension. Mods from here on in are pretty much gravy.

I wondered about the temp gauge mod. What is an RT temp gauge mod? Does a light not currently illuminate when the temps go high? Hell, there should be, considering the 80 has so many idiot lights for everything else. I hadn't even thought about it. My check engine light was already illuminated due to the pesky EGR issues I've been having.
 
Man, I didn't wanna be the smart-a** who commented on the cleanliness of your core, but since it's been done already, yeah, check out the joints between the header and the tubes!

The RT mod is RavenTai's mod to the temp gauge. As you well know, good write up from him on how to make it an "active" gauge vs. a passive one.

NCDoug...any thought of water pump while doing the rest of that enchilada cooling system PM?

Again, good luck, Shahram....
 
HOLY s***!

Glad no serious damage occured!
 
-Spike- said:
The temp guage mod needs an addition- an electrical contact on the needle that will illuminate a warning light whenever the temp rises above 'x'. I look at my guage all the time, but I know it will start to rise right after I glance at it, and it only takes a few seconds...

The Greddy aftermarket gauge that many of us use has the warning LED feature built-in as well as a trigger for an audible alarm or whatever you want. Photoman has a larger secondary warning lamp and an alarm buzzer wired to this trigger.

-B-
 
Shahram,

I just walked this same walk. My radiator developed a hairline crack a couple of minutes after pulling into the rest area in Gorman on the way home from vacation. No verheating after coming up the southbound grade. I always watch the temp guage like a hawk on the grapevine. Mo and I had just flushed and replaced the coolant just a couple of months ago. Did not, however, replace the thermostat. Local Yota dealer didn't have one in stock and I didn't the forsite to feed Dan's dogs on my previous order. Thanks to NorcalDoug's unfortunate mishap on the Death Valley trip I'd upgraded to the AAA plus membership so I had a 100 mile tow, not just the 7 mile standard. Had her towed down to Valencia. New radiator, hoses, thermostat, gulp.....labor. Beat them up on the labor hours they wanted and walked out the door light $1050. The wanted 1 1/2 hrs labor to replace the damn thermostat. I told the service writer it was a 20 minute job to remove 4 bolts, pull the old thermostat, put the new gasket on the new thermostat, put it back in and replace the four bolts. I think he was surprised I knew WTF needed doing (thanks Mo!). Still 3 hrs book labor for the radiator, knocked down to 1 hr for the thermostat and 1 hr he didn't tell me about to replace the radiator hoses. Damn hoses had to come off to replace the radiator and they still charged to put new ones on in addition to the cost of the hoses - WTF rippoff. Had no choice but to bend over as I was still 90 miles from home. I went with an OEM radiator - brass core was standard on the '94, but a big thanks to Dan for the part number to confirm they'd used the correct radiator.

Hope everything works out my friend! I'd just dropped come serious $$ on the INTI rack, drawer system and a GPS, so this hurt big time.
 
Brentbba said:
I'd just dropped come serious $$ on the INTI rack, drawer system and a GPS, so this hurt big time.

Its addictive isnt it?

I remember when i first drove up to your place to look at your sliders and kaymar. Your reply was something like "yeah, this will probably be it for awhile, i want to stay mild" HA! :D

Welcome to the addiction. Unfortunately, it only gets worse!

:flipoff2:
 
Back
Top Bottom