Power Steering Fade-Solutions?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 2, 2012
Threads
42
Messages
1,849
Location
Somewhere in the desert
Search sucks, I didnt find anything.

I have an FZJ80 running 315s and full armor (its heavy) tires were aired down to 14psi for a trip. Power steering constantly faded from what I am assuming is heat while running dunes most of Saturday. What intercoolers work for the system to cool it down? It sucks going from power steering to manual while carving bowls...

Intercooler links would be great and also mounting locations for the set up that are not fab intensive. I lost almost all my tools when my 60 rolled in a collision 2 months ago so the easier the better.
 
Last edited:
I've never experienced steering fade myself even with 315s and Pismo dunes, including this past weekend so I'll first say there is likely an existing issue. But I'll also say that I've removed the paperclip and replaced with Derale power steering cooler which gives me an extra quart.
 
I've never experienced steering fade myself even with 315s and Pismo dunes, including this past weekend so I'll first say there is likely an existing issue. But I'll also say that I've removed the paperclip and replaced with Derale power steering cooler which gives me an extra quart.

Based on my driving style (WOT for extended periods of time with minimal stopping) I am going to safely assume its heat related. Thanks for the suggestion on the cooler I will be looking into it. Ps, i got 3.6mpg on Saturday and burned 20 gallons of fuel, went 73 miles total...

I use a tranny cooler with a cheap cooler fan from eBay. Keeps the steering fluid nice and cool. I just have a switch on the dash and turn the fan on when I'm offroad.

Did you run the fan on the ign/acc circuit or is it a constant hot loop to run? factory 80 tranny cooler or different?
 
I used a generic cooler and fan. Look up transmission cooler fan on ebay. Lots of choices. I don't remember how I wired it. I think it's wired to the battery with a in-line fuse and a light up toggle switch on the dash. Find a spot u have room to mount it, measure that spot, find a cooler and fan to fit that spot and mount it. Run your steering return through the cooler.
Here's an example:
STACKED PLATE HOT ROD ENGINE OR TRANSMISSION OIL COOLER WITH SHROUD AND SPAL FAN | eBay
 
When was the last time you flushed the PS system?
If it's been a while fresh clean fluid might make the problem go away.
Trouble shooting 101; try the easiest things first.
 
When was the last time you flushed the PS system?
If it's been a while fresh clean fluid might make the problem go away.
Trouble shooting 101; try the easiest things first.


Not a clue, I have only had the truck a month an a half. Fluid didn't smell burnt on the dunes but I was planning on draining when putting in an intercooler anyway. Only issue is I wont have a trip to trouble shoot it under similar conditions until summer season and I would rather not find out it needed a cooler on rubicon or TnS next year. At this point I am going to throw one in regardless since it cant hurt to run cooler.
 
I get it too, of course I'm running 40's and hydro assist. I have been meaning to add a cooler for a long time, just haven't got around to doing so.
 
I get it too, of course I'm running 40's and hydro assist. I have been meaning to add a cooler for a long time, just haven't got around to doing so.

Yeah hydro assist is on the far back burner, it has a ton of front axle mods to be able to run it safely, I think i would be seitching to beadlocks running hydro assist though. just need the $$$
 
Not a clue, I have only had the truck a month an a half. Fluid didn't smell burnt on the dunes but I was planning on draining when putting in an intercooler anyway. Only issue is I wont have a trip to trouble shoot it under similar conditions until summer season and I would rather not find out it needed a cooler on rubicon or TnS next year. At this point I am going to throw one in regardless since it cant hurt to run cooler.
Your choice. I prefer not to add complexity until there is a proven need, every hose and fitting is a potential failure point.
 
Your choice. I prefer not to add complexity until there is a proven need, every hose and fitting is a potential failure point.

I do agree with you there, simplicity is best. Though if a Power steering line breaks its not the end of the world
 
I do agree with you there, simplicity is best. Though if a Power steering line breaks its not the end of the world
I would suggest you use the fittings made by Parker that can be used in the field to make new hoses. I use them on my FJ40 PS and carry an extra length of hose.
 
Here is my solution (not unique to me).

IMG_9795.webp
 
I would suggest you use the fittings made by Parker that can be used in the field to make new hoses. I use them on my FJ40 PS and carry an extra length of hose.

Link to those? I haven't heard of that.

Here is my solution (not unique to me).

View attachment 1351823

Sweet, I was wondering if you used that style or the flat. how is it protected under there? Looks fairly exposed. I am running a Labs Front bumper but want to swap it out with something beefier up front.

Plumb a better cooler. Annoying but itll fix it

Yep that's the goal
 
Sweet, I was wondering if you used that style or the flat. how is it protected under there? Looks fairly exposed. I am running a Labs Front bumper but want to swap it out with something beefier up front.

Protected from what? I'm not worried about it. If I hit something that destroys that cooler then I have other things to worry about :P
 
Just a comment, an intercooler cools air coming out of a turbo or supercharger.
In answer to your question though, a small transmission cooler should disperse more than enough heat and could be tucked up in front of the A/C condenser and radiator, maybe with a fan if you do a lot of slow speed stuff, and should eliminate the problem, and while you're installing it, I would suggest a fluid flush and replacement to give a nice solid base to start from.
 
Last edited:
I agree starting with a couple drain/refills might be all it needs. Mine made all kinds of moans and groans as well as loosing assist until I filled it up with fresh fluid. An extra cooler might be good too if you really beat the snot out of it, but I would try clean fluid first since you'll want to do a couple changes anyway.
 
I would suggest you use the fittings made by Parker that can be used in the field to make new hoses. I use them on my FJ40 PS and carry an extra length of hose.
Typically a steering cooler is mounted on the low pressure return side, so high pressure fittings and hose are not necessary. Standard hose clamps work fine rather than expensive fittings unless u just want the Bling factor.
 
Back
Top Bottom