Please attach your aftermarket bumper properly...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Oh Snap!
THAT-GUY_DR.webp
 
Also, don't try to use the bullbar portion of your bumper as an extraction point... stupid move!
 
Oh Snap! That sucks. Was he trying to yank him out or just pull?
 
Last edited:
he yanked. you can see the diesel smoke spewin and hear the revs increase.

That is where a winch woulda paid for itself.....just to prevent the shame/mocking....
 
Uhhh... since when is a bull bar a recovery point? The leverage alone f'd it up.
 
I don't think it was bullbar failure, looks like the frame horns snapped.

The point is that by attaching to the top of the bull bar, the force of the pull was a huge lever and snapped the mounting points on the frame horns.

Sad thing is the guy either didn't have proper recovery points like on the Slee front bumpers, or he didn't want to get his feet wet and attach to them. I think even the ARB tabs would have been OK in that pull. Plus, he didn't get much help from the guy driving the recovery rig.

-B-
 
I think the pointing and laughing is probably even worse than losing your bullbar and half your frame.
 
So in this situation the best thing would have been to use the 12 ton D shackles hanging off my kind of flimsy looking ARB recovery points? OR would I use the factory recovery points that we reinstalled below the ARB and are mounted to the frame.

Also now I have the D shakels hanging from the ARB is it stronger to attach these to the factory recovery points?
 
I'd personally take the factory recovery points over the cheesy tin I've seen hanging off of every ARB bumper I've bothered to look at. Of course, you realize that just bringing up the factory recovery points is going to send this thread into a raging death spiral, 12 pages of how safe/deadly the things are.
Thanks a lot.

-Spike
 
LOL sorry. Little did I know, but if true that these factory points are no good then I now have a total of 4 recovery points that are iffy on the front of my truck?

Is there any gear that would allow you to use 2 recovery points..Kind of a "Y" strap or something. I have a Winch Mount ARB so dose this mean I really never use my recovery points?
 
Search this forum for opinions on factory recovery points. You'll get opinions going both ways. Beefing up the ARB points doesn't look too hard, or simply changing out the factory rings for good hooks or adding some D-ring mounts would give you a warm fuzzy feeling next time you are involved in a recovery.

-Spike
 
You can use the factory recovery loops. They are fine and much better than the tabs on the ARB bumper.

-B-
 
They are fine and much better than the tabs on the ARB bumper.

-B-

I would definitely agree with that. For the record, I don't have any bad experiences with factory hooks, they left my truck along with the last few inches of my frame. To me, they look fine, but some will disagree.

-Spike
 
Sad thing is the guy either didn't have proper recovery points like on the Slee front bumpers, or he didn't want to get his feet wet and attach to them. I think even the ARB tabs would have been OK in that pull. Plus, he didn't get much help from the guy driving the recovery rig.

-B-

Search this forum for opinions on factory recovery points. You'll get opinions going both ways. Beefing up the ARB points doesn't look too hard, or simply changing out the factory rings for good hooks or adding some D-ring mounts would give you a warm fuzzy feeling next time you are involved in a recovery.

-Spike


I've been that guy on top of the truck, he just needed to come to realization that he f'ed up and get cold and wet.


And beefing up the ARB points isn't tuff at all. Just welding some plate to one side of the tab is enough, but welding plate to both sides is golden.

But I still have to wonder about a bull bar that is 'air bag approved' and just how much bull is in the bar.
 
80's ARB is not air bag approved.
 
Back
Top Bottom