Non-USA 4spd.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

you guy have to sourt this out i have only four speeds. I here there is a shipping company called UPS but i need to sourt out a taxi truck to take from my place to the port as i live out of perth WA.I would not be to woried about input shafts you can buy them very cheep brand new now.All are interchangeable on each box.In return i am trying to locate pentronics no dealer in australia would like to chat whith someone on that.
 
I can find you a pertronix, no problem.

It is very important that these be out of gas powered trucks, and output shaft for most will need to be 10 or 16 spline. The price of input, output shafts and a rebuild kit will make it cheaper to go buy from SOR...
 
Pin_Head said:
Where about in Oz can I get some of these H41s? I am going to be in Melourne in Febrary and I may want to take a couple back in my luggage.

That's a good idea, other than the sheer weight. To make luggage lighter, can the guts of a h41 be placed into a h42? Are the shafts and case the same? To put it more simply, can the gears out of a h41 be placed on the shaft of a h42, reguardless of input shaft length and spline count?
 
Nick the Carpenter said:
i live in australia and have about 6 lieing around if you want then i will put on a create and you sourt out the transport.I think there too good to scrap

where in aus are you? some of us aussies need gearbox's too :)
 
folsom50 said:
That's a good idea, other than the sheer weight. To make luggage lighter, can the guts of a h41 be placed into a h42? Are the shafts and case the same? To put it more simply, can the gears out of a h41 be placed on the shaft of a h42, reguardless of input shaft length and spline count?

I think the answer to your question is no. The H41 and H42 are the same length, but the H41 is fatter to accomodate the larger gear. I had to bend the shifter linkage a little because it was contacting the side of the H41 before fully engaging.

gary
 
coiled40gary said:
I think the answer to your question is no. The H41 and H42 are the same length, but the H41 is fatter to accomodate the larger gear. I had to bend the shifter linkage a little because it was contacting the side of the H41 before fully engaging.

gary

?? They're both toploaders.

The cases are not noticably different but I asked the question about whether the H41 gearset could be installed into my H42 case before I bought an H41 and was told in here that it couldn't be done or wasn't worth doing.

Do a search on "H41" and read several threads on the whole subject.

BTW, the H41 ratios are:
1st = 4.93
2nd = 2.64
3rd = 1.52
4th = 1.00 :1

All else remaining stock the H41 jumps the crawl ratio from 28.55:1 to 39.56 in 1st low range. Put together a 3 speed TC and have 46.71:1, or do the nasty with Orion and go slow with 80.77:1.

The H42 ratios are 3.56, 2.29, 1.41, 1.00
 
72cruiser said he was going to work on it, but sounds like there is only 4 of them to be had, unless we another member in oz willing to help us out.......
 
or toss a marlin box in the mix with an H41 and get yourself around 150:1.

That's been my plan, but I need the 19-spline for the 3B and split case.
 
ClemsonCruiser said:
72cruiser said he was going to work on it, but sounds like there is only 4 of them to be had, unless we another member in oz willing to help us out.......
Not following.
 
72 cruiser was going to talk to Nick about his H41's, and look into shipping from OZ......... I was saying he said he only has 4 trannies, nick that is, and I think more than 4 people want in on the deal if we can work it out.

Hope that helps, if you have questions PM 72cruiser..........
 
Back
Top Bottom