New steering issue

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 3, 2014
Threads
57
Messages
704
Location
Aspen
Well I’m stumped.


After doing some dumb crawling the steering on my cruiser is so weird. Turning to the left the steering is light and not smooth at all and turning to the right the steering is smooth and seems normal except for maybe having a little bit more resistance. I can’t see anything bent underneath and it still tracks in a straight line. However whenever I turn to the left going highway speeds it is very jumpy and overall it just doesn’t seem very settled. It has 3 degree rubber castor bushings in it. I have attached the video where I caused the whole problem. I was never forcing the power steering and I didn’t hit anything super hard I don’t think except the rock slider.

It seemed like such a fun idea at the time but looking back on it it was not the brightest idea.


Link to the video



Any suggestions?

Thanks!
 
Not exactly sure. Just was spot to check. Also all the linkage stuff and bushings. It seems I have read the symptom of one direction turning being more difficult, but drawing a blank on the thread and cause.
 
DId you bend / break your steering damper? Is it old / new?

Is your PS pump full of fluid?
 
DId you bend / break your steering damper? Is it old / new?

Is your PS pump full of fluid?

Steering Dampner visually looks fine. It’s a OME and I’ve had it on for around a year and 20k miles. Power steering fluid level is good I did change the high pressure lines around a month ago I don’t think it has an correlation to this though.
 
Steering Dampner visually looks fine. It’s a OME and I’ve had it on for around a year and 20k miles. Power steering fluid level is good I did change the high pressure lines around a month ago I don’t think it has an correlation to this though.

Did you properly bleed the system and get out all the air? It takes about 100 cycles each way (SLOWLY) with it shut off and the front on jack stands, then do the same with it running.
 
Did you properly bleed the system and get out all the air? It takes about 100 cycles each way (SLOWLY) with it shut off and the front on jack stands, then do the same with it running.

I bled it on with the wheels on the ground. Maybe that’s it but it’s been great for the past month. Worth a shot to try though
 
Don't feel bad. The video looks like you were screwing around well within reason. Real wheeling will demand worse loads on things. But what do you mean "steering is light" when turning to the left? Like... its unusually easy? That would imply something funky in the box.
 
Don't feel bad. The video looks like you were screwing around well within reason. Real wheeling will demand worse loads on things. But what do you mean "steering is light" when turning to the left? Like... its unusually easy? That would imply something funky in the box.

Unfortunately that’s sorta what I’m thinking it is. I re bled the power steering with no luck. Steering being light I mean there is a little resistance turning to the left. Like a decent amount less resistance then there use to be. Then to the right there is much more resistance. Turning to the left it is very jumpy as well where that as not a problem on the right. Is it worth adjusting the steering box would that do any good?
 
Unfortunately that’s sorta what I’m thinking it is. I re bled the power steering with no luck. Steering being light I mean there is a little resistance turning to the left. Like a decent amount less resistance then there use to be. Then to the right there is much more resistance. Turning to the left it is very jumpy as well where that as not a problem on the right. Is it worth adjusting the steering box would that do any good?
Probably not. If its jumpy and super loose when turning to the left (even with the tire against a curb or other monument kinda thing) then it would suggest the valve in the box is wonky. It seems like a bizarre failure mode but nothing else i can think of would cause asymmetric power steering application like you describe. @Tools R Us ?
 
Not overly impressed with the video, urban wheeling doesn't help our quest to be a respectable/responsible recreation group, that said, have seen much worse, so :meh:.

Don't see any obvious indication of trauma, have seen much worse abuse on the real trails. My first step would be to put it on stands, run the steering back and forth, check for any contact, bind points, check knuckle arm nuts for proper torque (71ft/lb), etc. If there is nothing and the bind is still there, disconnect the drag link end from the pitman, if the bind is still there, it's most likely in the box.
 
Did you properly bleed the system and get out all the air? It takes about 100 cycles each way (SLOWLY) with it shut off and the front on jack stands, then do the same with it running.

Some of you have weird/silly bleeding rituals, you know that it will self bleed,, right? When you stand it up on the rear bumper and suck the system full of foam/air, do you stop and do this silliness? Oops, first you would have to go on the trail!:hillbilly:
 
Some of you have weird/silly bleeding rituals, you know that it will self bleed,, right? When you stand it up on the rear bumper and suck the system full of foam/air, do you stop and do this silliness? Oops, first you would have to go on the trail!:hillbilly:
I crank it back and forth a few times, turn it on, let it foam and whine for a sec, turn it off, wait, then refill and rock out
 
Some of you have weird/silly bleeding rituals, you know that it will self bleed,, right? When you stand it up on the rear bumper and suck the system full of foam/air, do you stop and do this silliness? Oops, first you would have to go on the trail!:hillbilly:

Some day when I have time, in between checking all my suspension fasteners, fixing the window motors, bleeding the cooling system, changing the front main seals, cleaning out the rear window gutters, and raising the spare tires, and adding front and or rear bumpers, and , of course, checking my knuckle studs.........I will again look up the FSM procedure on this and let you know.......

I don't just make up this s***. I know you don't either. You work on a lot of OTHER PEOPLE's trucks. Your job is to get them in one door and out the other, hopefully correctly and quickly to make the $$$$$$$$$$.

Mine is to work on it when it needs. Drink beer in between. Read 'Mud while drinking said beer.

Then, of course.......6, 4, 6.

And by the way, I ALWAYS make sure I wear my good luck socks when working on the LC.......
 
Not overly impressed with the video, urban wheeling doesn't help our quest to be a respectable/responsible recreation group, that said, have seen much worse, so :meh:.

Don't see any obvious indication of trauma, have seen much worse abuse on the real trails. My first step would be to put it on stands, run the steering back and forth, check for any contact, bind points, check knuckle arm nuts for proper torque (71ft/lb), etc. If there is nothing and the bind is still there, disconnect the drag link end from the pitman, if the bind is still there, it's most likely in the box.


Appreciate the response. I’ll do all the procedures you just mentioned. As far as the urban wheeling is concerned I did it to try to get around to a front of a car with a dead battery. There was a fence so I could not just simply drive it forward. I had permission to do what I did. We ended up having to roll the dead car backwards and block traffic. It was just a fun attempt I thought I could do. Not the brightest idea but I did have permission. Thanks for the response I’ll take all those steps tonight. Thank you!
 



maybe not your issue, but this ^^^ caused a funky steering feel on my rig.
Similar to what you describe. Felt lighter in one direction than the other, also felt clunky in one direction.
It me a little while to find, but was obvious when the tire rods were disconnected and the knuckle could rotated separately to everything else.
 
Back
Top Bottom