New shocks affect steering wheel centering?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 14, 2009
Threads
36
Messages
2,932
Location
North and South of Mason Dixon
I just replaced my very old Ranchos with new Bilsteins. Downside up with no boots as recommended. Now it rides like a truck instead of a bus...

I drove around for a few miles-just flat roads-and noticed that the steering wheel seems out of center by a few degrees now. I don’t see how that can happen. This makes no sense. I didn’t even jack the truck up. I didn’t measure before, but the frame is level to the ground now left to right to within 1/16 both in the front and the back, I’m not too concerned about the steering because my next project is likely new TRE’s, but does this make any sense?

4E0F8B1D-7B8A-496D-B437-7A5A02BE0CCC.webp


12E36191-03A4-46BD-8EF8-E663DDCF927B.webp
 
I just replaced my very old Ranchos with new Bilsteins. Downside up with no boots as recommended. Now it rides like a truck instead of a bus...

I drove around for a few miles-just flat roads-and noticed that the steering wheel seems out of center by a few degrees now. I don’t see how that can happen. This makes no sense. I didn’t even jack the truck up. I didn’t measure before, but the frame is level to the ground now left to right to within 1/16 both in the front and the back, I’m not too concerned about the steering because my next project is likely new TRE’s, but does this make any sense?

View attachment 2073932

View attachment 2073933
I am confused about the suspension.

You have what looks like spacers between the axle housing and springs that in my mind would lower the vehicle but then it looks like you have longer shackles that would raise the vehicle.
Maybe you or someone could clue me on this.

What is that showing behind the bumper in first photo?

Do you have the right length shock? Could they be bottoming out?
 
I am confused about the suspension.

You have what looks like spacers between the axle housing and springs that in my mind would lower the vehicle but then it looks like you have longer shackles that would raise the vehicle.
Maybe you or someone could clue me on this.

What is that showing behind the bumper in first photo?

Do you have the right length shock? Could they be bottoming out?
Those “spacers” are tapered caster shims. The shocks are the right length-half way plus or minus from the neutral position. And I’ve not gotten anywhere near bottoming out. The thing behind the front bumper does not affect anything. Thanks for taking a look.
 
Now it rides like a truck instead of a bus...
Swap those ancient 3 leaf Rancho springs for any other lift or stock springs for a real ride improvement... The ride is like a tank with those springs. I still have a set on the wife's project cruiser waiting to go to the recycle pile once its running again. I will switch back to stock springs since the rear fenders were cut out long before me by a PO.
HTH,
Will
 
Those “spacers” are tapered caster shims. The shocks are the right length-half way plus or minus from the neutral position. And I’ve not gotten anywhere near bottoming out. The thing behind the front bumper does not affect anything. Thanks for taking a look.

Doh! caster shims.
So the thing behind the bumper does not affect anything but am still wondering what it is.
 
Swap those ancient 3 leaf Rancho springs for any other lift or stock springs for a real ride improvement... The ride is like a tank with those springs. I still have a set on the wife's project cruiser waiting to go to the recycle pile once its running again. I will switch back to stock springs since the rear fenders were cut out long before me by a PO.
HTH,
Will
I think they are actually "Burbank Springs" I bought a set in 1979 when I was nineteen. Worst investment ever. They were so stiff I
finally swapped them for Ranchos after one of the forward rear spring hangers nearly pulled from the frame. If I approached a curb at an angle a tire would lift. There wasn't a lot of spring options back then. The only suspension the truck had was frame flex
 
I'm wondering how you are steering the rig.
looks like nothing is attached to the center arm in the first pic??
 
I would flip those shocks maybe the drag link is rubbing on the shock.
Thanks. The old shocks were this way too and lots of 40’s have shocks this way. They are not close enough to drag link to rub.
 
Several folks on this forum have reported that the boots have trapped condensation and junk inside.
 
When I replaced my entire suspension my wheel was off almost 90 degrees. It settled a little after driving and then again when I installed the cruiser lean plate. I eventually had to pull the steering wheel and re-center it. Not really the proper way of centering the wheel but I had great alignment and didn't want to mess with a good thing. You may want to drive it and flex the suspension a bit before making any changes.
 
Back
Top Bottom