Need some advice...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Get it down to $1900, Monstaline, Sawzall the arches, 3" lift, put 40's on it, weld the rear, selectable up front, and enjoy it as a rock donkey.

If you want something nice looking as a DD then keep looking...IMO.
 
I would pay $2500 for that. Needs a full, everything, but it's a decent carcass and it has cloth. Get your checkbook out and get ready to get greasy.

I am looking forward to working on this LC. I know it is going to take some time to get it back to baseline but as long as it works mechanically I am good, function is more important to me. It needs to get me to and from work, 15-40 min round trip commute.

Mine was in great shape and I still spent over $2k on Parts alone just base lining it to where I felt comfortable going on longer trips

My main priorities once I get the LC is to check the drive train, replace the fluids in the tranny/diff/transfers, A/C etc. Then get on those brake issues. A Nissan group I am part of gets 10% off on parts...
 
Be prepared to spend mucho deneiro but don’t feel bad about it because you will be resurrecting and driving one of the baddests beasts to ever roll off an assembly line. It’s worth it because life is too short to drive an Xterra.
 
Last edited:
I paid $2500 for this on the east coast. No rust, mechanically functional, no interior, headliner or front bumper. Has working factory lockers though.


00Q0Q_ffbT1g1Dez0_1200x900.webp
00808_72psHcU8gBB_1200x900.webp
 
No AC.
Needs tires.
Body damage.
Some bearing/belt on a pump/alt.
Rotors/ABS issue.
Looks neglected.

That's $1500-2k of work all day. And that's only what you know of. There is another $300-$1000 hiding.

You can find a better/ cleaner start for $3500.

TLC are 30% more than other trucks...

30% heavier
30% more fuel consumption
30% more expensive
30% cooler
30% more capable

A 1997 4Runner with 200k is a nice and easy DD replacement. That rig is a project.
 
Be prepared to spend mucho deneiro but don’t feel bad about it because you will be resurrecting and driving one of the baddests beasts to ever roll off an assembly line. It’s worth it because life is too short to drive an Xterra.

LOL in regards to the Xterra comment. I have wanted one of these for awhile and the opportunity presented itself recently. As I have mentioned before if the LC is mechanically sound I am good. It only has to take me to and from work, 40 min round trip.

I paid $2500 for this on the east coast. No rust, mechanically functional, no interior, headliner or front bumper. Has working factory lockers though.


View attachment 1684854 View attachment 1684856

Great find.

No AC.
Needs tires.
Body damage.
Some bearing/belt on a pump/alt.
Rotors/ABS issue.
Looks neglected.

That's $1500-2k of work all day. And that's only what you know of. There is another $300-$1000 hiding.

You can find a better/ cleaner start for $3500.

One thing I do plan on doing and have started is a list of checks or maintenance that I believe will/or is needed right away. The first things I plan on tackling are the brakes, the front axle if that IS leaking, recharging the A/C and fluid changes.

To fund this project I get free guns from manufactures and plan on selling them to help with the repairs/fixes.
 
2500 is a good price as long as the whining sound isn’t anything bad. look on carfax to see how many owners and all that jazz.

Im in mesa, might be selling my trailgear front bumper in the next few months, gonna build my own.
 
2500 is a good price as long as the whining sound isn’t anything bad. look on carfax to see how many owners and all that jazz.

Im in mesa, might be selling my trailgear front bumper in the next few months, gonna build my own.

Does anyone have a Carfax account? I do have the VIN and could send it to you.
 
I would be inclined to pass, but that's just me.
I'd also suggest looking at the fuse box and wiring by the EGR, and under the dash. If 3 PO's have all been monkeying around with the wiring I'd like to know that and wouldn't be super excited.
Not trying to be harsh, just offering an opinion. I looked for an 80 for close to a year. The longer you can shop the better you might do. I think you can find other comparable 80s at that price without lockers without too much trouble.
 
I paid much less for the one I drive, but I threw $6K at it to turn it into my DD. I did ALL the labor.

5 Tires (Duratrac 285's)
All New Calipers (Napa Eclipse)
New radiator and all hoses (Toyota)
New Wheel bearings all four corners (Koyo)
New rotors all four corners (Power Stop)
New Brake Pads all four corners (Power Stop)
Front axle Rebuild Kit (Cruiser Outfitters)
Windshield Wiper Motor (O'Reilly's)
Alternator (O'Reilly's)
Starter (O'Reilly's)
Throttle Cable (Toyota)
Oil Pump Seal/Front Main Seal/Valve Cover Gasket/Dizzy O-Ring (Toyota)
Power Steering hoses and cooler (Toyota)
Hood Struts (Toyota)
Rear Hatch Struts (McMaster Carr)
Transmission Fluid Exchange (Valvoline Max Life - 5 gallons)
Spark Plugs / Cap / Wires (Toyota)
Front Knuckle Studs/Cones/Washers/Nuts (8) (Toyota)
SS braided Brake Hoses (Slee)
RCV Stock Replacement Axles/Birfields (Slee)

All of the above was just to make it a DD and that is what the $6K covers. It took me about a month to go through and get all this done with two months of gathering parts ahead of time. My truck was neglected badly. It wobbled and shook, and stopped poorly, but I still drove it 25K miles like that.

I have done a few mods to make it a little more fun.
Winch (12K Badlands)
(4) Offroad Driving Lights (O'Reilly)
Blue Sea Underhood Fuse Block

I have since put on another 50K with all those things and it is just now coming around for brakes. I have been able to do a few upgrade things that are yet to be installed:
OME 2.5" Lift with shocks
WKOR Sliders
Lexus Wheels (blasted and polished/painted)

That gives you an idea of rough cost of what you may throw at it to be a DD, in spite of the damaged fenders.
 
........And then the mods depending on the kind of wheeling you plan to do.
 
I paid much less for the one I drive, but I threw $6K at it to turn it into my DD. I did ALL the labor.

5 Tires (Duratrac 285's)
All New Calipers (Napa Eclipse)
New radiator and all hoses (Toyota)
New Wheel bearings all four corners (Koyo)
New rotors all four corners (Power Stop)
New Brake Pads all four corners (Power Stop)
Front axle Rebuild Kit (Cruiser Outfitters)
Windshield Wiper Motor (O'Reilly's)
Alternator (O'Reilly's)
Starter (O'Reilly's)
Throttle Cable (Toyota)
Oil Pump Seal/Front Main Seal/Valve Cover Gasket/Dizzy O-Ring (Toyota)
Power Steering hoses and cooler (Toyota)
Hood Struts (Toyota)
Rear Hatch Struts (McMaster Carr)
Transmission Fluid Exchange (Valvoline Max Life - 5 gallons)
Spark Plugs / Cap / Wires (Toyota)
Front Knuckle Studs/Cones/Washers/Nuts (8) (Toyota)
SS braided Brake Hoses (Slee)
RCV Stock Replacement Axles/Birfields (Slee)

All of the above was just to make it a DD and that is what the $6K covers. It took me about a month to go through and get all this done with two months of gathering parts ahead of time. My truck was neglected badly. It wobbled and shook, and stopped poorly, but I still drove it 25K miles like that.

I have done a few mods to make it a little more fun.
Winch (12K Badlands)
(4) Offroad Driving Lights (O'Reilly)
Blue Sea Underhood Fuse Block

I have since put on another 50K with all those things and it is just now coming around for brakes. I have been able to do a few upgrade things that are yet to be installed:
OME 2.5" Lift with shocks
WKOR Sliders
Lexus Wheels (blasted and polished/painted)

That gives you an idea of rough cost of what you may throw at it to be a DD, in spite of the damaged fenders.

Not ALL that is REQUIRED for a
Daily driver, but it COULD be, or, it COULD be even worse.
 
Jump on it! Forget the clowns saying “no way without lockers”. Factory lockers are the least desirable lockers in a 80 anyways. Throw a $350 Aussie in the rear (If you need it) in your driveway.....2.5 hours! I think I paid $35 for a front fender at pik n pull (had to wait 2 months for correct year). If you can prep it, probably $100-$150 for body shop to spray it. (That’s you carrying in just the prepped fender, ready to spray), you can find brand new tires on C/L in whatever size you want if your willing to drive an hour, or wait a month. Usually 50% less than what they paid new.
It all takes time. No one here (except maybe a couple spending momma and daddies $$$) built their rig overnight. Get it, start baselining and making a “to do” list, save some $$$, buy parts over time, and MOST important.... get your wife back in good health! Good luck!
 
Some local clown comments:

Jump on it! Forget the clowns saying “no way without lockers”. Factory lockers are the least desirable lockers in a 80 anyways.

So, what kinda deficiencies did you experience with your factory lockers?

Throw a $350 Aussie in the rear (If you need it) in your driveway.....2.5 hours! ...

I agree that a lunch box works pretty well, within the compromises of the design, in an '80. But no way it will be close to the capability of a select-able F&R locker rig, like a factory locked rig. As a local to the OP, can take him to places, within an hour of his door, where he will be wishing for or denied by not having a front locker. Other places where, as he is crab walking off the cliff, would be praying to be unlocked, something the lunch box is incapable of.

It fully depends on the intended use, some don't wheel to the level to need a locker. I like the Aussie, have installed and wheeled with many, but the factory lockers are significantly more capable, no question. If there is a choice, I would always take the factory locked rig, often can be had for little if any more $$$ and ready to go, less messing around before hitting the trail.
 
Keep this on track without personal attacks. Everyone is entitled to their opinion and let us be respectful of it

Thank you your 80's Forum Moderator
 
Some local clown comments:



So, what kinda deficiencies did you experience with your factory lockers?



I agree that a lunch box works pretty well, within the compromises of the design, in an '80. But no way it will be close to the capability of a select-able F&R locker rig, like a factory locked rig. As a local to the OP, can take him to places, within an hour of his door, where he will be wishing for or denied by not having a front locker. as he is crab walking off the cliff, would be praying to be unlocked , something the lunch box is incapable of.

It fully depends on the intended use, some don't wheel to the level to need a locker. I like the Aussie, have installed and wheeled with many, but the factory lockers are significantly more capable, no question. If there is a choice, I would always take the factory locked rig, often can be had for little if any more $$$ and ready to go, less messing around before hitting the trail.
Is this your experience with a rear Aussie locked 80? Have a Harrop up front in mine and an Aussie sitting on the shelf ready to go in the rear. Been in two rear Aussie locked 80s and never experienced the rear walking out. Not sure I want to install mine if this is a common issue...
 
I honestly think I am going to pick it up. All the information, the opinions that everyone has provided has been taken into consideration.

Everyone has expressed their apprehension about getting into something like this and I do understand it will take some time to get it to "baseline". The exterior of the LC is not really of importance to me. The fender will be fixed, and the lower valance under the headlights will be fixed or replaced.

Priority number one will be to get the mechanical gremlins taken care of. Be it the A/C, brakes, window regulators fixed or replaced and so on. Making sure the rest of the car is mechanically sound before I do any modifications is the main priority.

Here in AZ the pickings are slim out here. The number of LC's in surrounding states is crazy compared to here. Either Vegas, SD or LA are all about the same distance as far as driving, 5 hours.
 
Back
Top Bottom