Modified ARB

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 25, 2007
Threads
326
Messages
5,181
Location
Nashville
Hey all,
Don't know if this is a used and abused thread, but who out there has modified their ARB front bumper in any way? I have seen a couple, but just wondering who has hacked it up a bit and changed the approach angle.

Cheers,

Joel
 
I tucked mine in 2 & 3/8". Basically, I moved it back to where the old bolt hole in the front of the bumper aligned with the rear nut on the frame and drilled a new front hole in the bumper. It took a lot of trimming on the inside edge and part of the flat uprights. Then i cut the wing ends to follow the same line of the whel well opening like it was before and plated them. I also trimmed the skirt off and had the backside plated (from the sides of the winch hole to the ends of the wings). I removed the light tabs on the top bar to make sure they wouldn't hit the hood if I hit some thing hard. I also put a reciever hitch in the bottom angled part. My pictures came out dark, I'll take some out in the daylight tomarrow.

Of course, my cruiser doesn't have the AC dryer down there, I don't know how that would be effected.
P6270057.webp
P6270075.webp
 
Mine is modified. I love the improved approach angle. Basically the entire lower skirt was removed. Not sure what else to describe. This was done by the previous owner and he did a pretty nice job with it, seeing that the bumper had been in an accident.

you get a pretty good view in this pic.
17.jpg


maybe see a little here too...
96.jpg
 
do dents count? if so ive modified mine quite a bit
 
100_0328.jpg
 
That is Matt's.....aka AMMO he is on the board and I know for a fact that started as an ARB>>>>
 
Yeah, if dents and scrapes count, I'm in. I lightened mine up a bit by scraping some of the powder coating off. Went in to a sand filled corner a bit too fast and hit the canyon wall. If the ARB wasn't there, it would have taken out the headlight and likely the fender.
 
The only modifications made to mine are an added rubber air dam to direct air up to my Safari Tranny Cooler and some brackets to hold the transmission lines tight. :cheers:
 
Hey Turbo, can you post a pic of that? I just removed my 7" hellas yesterday because I thought they were blocking too much air flow...
 
Hey Turbo, can you post a pic of that? I just removed my 7" hellas yesterday because I thought they were blocking too much air flow...

Sure, it is super simple and it was supplied with the Safari Turbo kit. This is the view from behind the bumper. You can see a 1/4" rubber flap bolted to the bottom angled edge of the ARB and you can also JUST see the supports that hold the Tranny Cooler in place right where the ARB bumper angles to the reverse and to the bottom. It is a really clever place to put the cooler especially if one puts some expanded steel in front of the cooler and behind the bumper's open areas. Take a little looksee, if you would want other pics, I'll go snap some later today to post here.

Ohh, I should add that I've literally shoved the bumper over obstacles with that flap folded under the bumper's edge. I was COMPLETELY surprised that it did not damage it. I'm sure with enough weight transfer it would rip the thing right off but it is only a piece of 1/4 rubber that is about three inches tall by as wide as the flat bumper bottom. You could practically make another one right off of the trail with a big-rig's mud flap found on the side of the road. It's that simple.
Tranny Cooler Pic 2.webp
 
i spent may too much money on my arb to hack it up. but if i had damaged it and needed the clearance.... Although i did cut my samurai custom winch bumper and i absolutely love it HMMMmm
 
Back
Top Bottom