Mmmm Crack

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 3, 2006
Threads
17
Messages
84
Location
Vancouver, BC, Canada.
Website
www.paool.com
This could really go in any of the tech sections but since it is off my '40 I figured I'd best place it here. Anyhow.. It would seem my exhaust header has developed a crack and is quite noisy. I'm not sure if this is a result of adjusting the valves while it was running, or the 4 hour drive it took to get it home from the PO's, but it doesn't really matter at this point..

The question is... Should I bother repairing this (is it repairable?) or simply buy another header? I'd rather repair it for now, but i wanted opinions from people, as to whether it might just blow out the weld, or continue to crack etc etc..

the images are large save for one, so I'll just link them:
crack2.jpg

http://paool.com/images/crack1.jpg
http://paool.com/images/crack3.jpg

Thoughts? opinions?
 
I'd say just get a new one. That what I did after I damaged mine by catching the PO's craptastic muffler on a tree I was going over. Much easier.
 
Oooh!! Perdy... expensive! heh.. but still pretty damned nice. coming from you, I'll assume they're worth the cost. Definetly an option now...

however, just for curiousity sake, is it safe to run the current headers the way they are? or with a temporary bead of weld to plug up the hole, or could I run the risk of hurting the engine?
 
I'm cheap, and so have welded cracked headers before. Some times it works out, some times you have to do it again in a few monthes. anything that expands and contracts that much that often is gonna be prone to cracking from the get go, but add a weld and the funny stresses you can potentially induce and it can get worse. But I'd weld it any way. Really the worst thing that's happened so far is a loud ride home to weld it some more.
 
please elaborate

Trollhole said:
I hate those headers. And as Poser said it is okay to weld. Just don't expect it to last long.

Could you explain hating them, my current headers may need to be replaced sooner than later and I would like to know whats on your mind about the MAF ones.
 
The 6 into 1 headers have been around since the 70s. I bought my first set in 1977. The ceramic 2 peice seal better and the ceramic run cooler and last longer. I just bought the 6 into 1 because it was what I had before and you can buy 3 sets for the price of the ceramic. I had to make up some half washers to mount them right (stud holes are big).


Kevin
 
1phrogguy said:
Could you explain hating them, my current headers may need to be replaced sooner than later and I would like to know whats on your mind about the MAF ones.

Because the warp, the rust out, they were not enginered very well, you have to use all kinds of ground down washers to get them to fit correctly. They just plain suck. I have been through a couple and swore I would never buy another one again.
 
Trollhole said:
Because the warp, the rust out, they were not enginered very well, you have to use all kinds of ground down washers to get them to fit correctly. They just plain suck. I have been through a couple and swore I would never buy another one again.


I'll agree here, and no one here at Man-A-Fre is afraid to admit it either. Despite the fact that you have to put in extra effort to get them to work right, they are still one of our #1 selling products. If you can afford it, the tuned headers are a much better option. We could make the 6>1 headers nicer, but then they wouldnt be $150.00 anymore. :doh:

:beer:
 
Back
Top Bottom