Meet Merl

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 1, 2014
Threads
2
Messages
28
Location
Austin, TX
Meet Merl.

I bought a year and a half ago from her second owner down in Universal City, Texas – I'm her third owner. Mostly stock, lots of work to be done, I'm so proud and also in way over my head. My aim is to get her running reliably as my daily driver then ready for a few weeks in Big Bend and bigger camping trips. I'd like to keep it simple and take good care of her for years to come.

Several problems have already popped up so I'm aiming to chronicle my aimless wandering through the internet, word of mouth rabbit holes, mechanic shop talk and total noob failures with Merl.

TejasMerl_JesterKing.webp


1983 FJ60
248,499+ miles

Known issues:
leaking seals and gaskets
oil pan leak
leaking catalytic converter
dead cylinder (#5 compression tested at 94) < advice is appreciated here
broken odometer
when cold, turns over 10x before starting <advice is appreciated here
no air conditioning
broken window regulators on driver door and rear passenger door
passenger side door doesn't unlock from outside

Current plans:
fix above issues then:
locking center console
fix window regulators
new bumper corners
hefty roof rack
finish new upholstery
fix rust
paint job?
new carpet (details available for those interested)
window tint (details available for those interested)
yakima rack
new master pump cylinder
new battery
new alternator
new tie rod ends
replace belts & hoses
new muffler
steering wheel wrap
break, gas, clutch pedal pads
replace air & fuel filters
stereo
(need to replace post-theft)
speakers (details available for those interested)

I'm pretty stoked to be here. Any advice ya'll have on the above issues, questions for me or forum posts you can point me to, I'd appreciate it.

Check out #TejasMerl on Instagram or Google for more photos of my daily adventures.

TejasMerl_interior.webp photo-5a.webp TejasMerl_wildflowers.webpphoto 3.webp
 
Very comprehensive list and looks like you are using her for what she was meant to do: Cruise. :)

Regarding dead cylinder:

Only 3 real options:

1. Diagnose and fix: Could be a stuck valve or piston rings. If it's the valves, you can do a head job and have machine shop fix it.

If it's rings, rings can be replaced (not the cheapest option).

2. Drive as is and deal with it (cheapest route in the short run, most expensive in the long run).

3. Swap out engine for a domestic V8 (plenty of info on swaps on MUD).

Regarding starter: You can replace or rebuild with the former being the quickest/easiest route (though a bit more expensive), or you can rebuild starter for about $45 in parts.

Welcome to the tribe.

:cheers:
-onur
 
Welcome, Merl. This is the best place in the world to get advice and to learn to fix your new Land Cruiser.

For your cold starts; finding the sweet spot to set the choke should help. Possibly the carb needs some TLC.
 
Welcome indeed, did you pull up next to this guy on Saturday?
1407282997360.webp

If not then there's another lady in Austin with a white or beige 60.
 
^^x2 on what Juggernaught says.

The choke plate should make a nice, tight seal over the throat of the carb.

To check, remove the air filter. With the engine off, pull the choke handle in the vehicle cabin out all the way. Go back the engine bay and push down on the choke plate on the edge. If it moves, even 1mm, then you've got to take up slack in the cable.

To take up slack in the cable, push the choke handle in the cabin back in. Go back to the engine bay and find the bracket that holds the choke cable housing behind the carb. Loosen the screw on the bracket and slide the cable housing back slightly (adjusting as necessary) to take up the slack on the cable attached to the choke plate arm then retighten the screw on the bracket.
 
Welcome indeed, did you pull up next to this guy on Saturday?
View attachment 926081
If not then there's another lady in Austin with a white or beige 60.


^^^IF YOU DID RUN, AND RUN FAST!! HA! Just kidding! The Austin group has some phenominal people, Mike included. There is a great wealth of knowledge there and a great resource with CruiserYard for "used" and new parts.

Welcome aboard.

J
 
Texas is the place to be.

I like the story you've got going. Good renovations thus far.

Followed you on Instagram. Wish I was in the Hill Country more often. Houston is... Well, a swamp.
 
Welcome Merl looking forward to the build
 
Welcome! Looking forward to the build :D
 
adjust the valves first, then retest comp...tight valves will lower comp; low comp will require cranking to catch fire...Beno BTW is a good dude to know...
 
Very comprehensive list and looks like you are using her for what she was meant to do: Cruise. :)

Regarding dead cylinder:

Only 3 real options:

1. Diagnose and fix: Could be a stuck valve or piston rings. If it's the valves, you can do a head job and have machine shop fix it.

If it's rings, rings can be replaced (not the cheapest option).

2. Drive as is and deal with it (cheapest route in the short run, most expensive in the long run).

3. Swap out engine for a domestic V8 (plenty of info on swaps on MUD).

Regarding starter: You can replace or rebuild with the former being the quickest/easiest route (though a bit more expensive), or you can rebuild starter for about $45 in parts.

Welcome to the tribe.

:cheers:
-onur

adjust the valves first, then retest comp...tight valves will lower comp; low comp will require cranking to catch fire...Beno BTW is a good dude to know...

Thanks for th advice Beno and Lamb - sounds about right. My plan was to do a valve adjustment and test the compression at running temp then reevaluate. I'm running her on 5, which is fine for now but I do need to fix it. Engine swap is probably very far down the line.
 
Welcome, Merl. This is the best place in the world to get advice and to learn to fix your new Land Cruiser.

For your cold starts; finding the sweet spot to set the choke should help. Possibly the carb needs some TLC.

^^x2 on what Juggernaught says.

The choke plate should make a nice, tight seal over the throat of the carb.

To check, remove the air filter. With the engine off, pull the choke handle in the vehicle cabin out all the way. Go back the engine bay and push down on the choke plate on the edge. If it moves, even 1mm, then you've got to take up slack in the cable.

To take up slack in the cable, push the choke handle in the cabin back in. Go back to the engine bay and find the bracket that holds the choke cable housing behind the carb. Loosen the screw on the bracket and slide the cable housing back slightly (adjusting as necessary) to take up the slack on the cable attached to the choke plate arm then retighten the screw on the bracket.

To clarify - she doesn't like to start after sitting in the garage for a few days, even if it is hot outside. I'll turn the engine over 12 separate times before it catches. The above sounds like a good place to start - I'll look into it and let ya'll know what I discover.
 
To clarify - she doesn't like to start after sitting in the garage for a few days, even if it is hot outside. I'll turn the engine over 12 separate times before it catches. The above sounds like a good place to start - I'll look into it and let ya'll know what I discover.

Yeah, that's a cold start. You shouldn't need the choke on hot starts (restarts after the engine is at operating temp). Does it require the choke on hot-starts?

I had a similar problem, but with winter time overnight temperatures dipping down into the -10 or -20 degrees last winter and readjusting the choke plate to make a nice tight seal solved the problem. It's because the choke plate creates the proper vacuum for the carb to draw enough fuel from the fuel bowl...

I think Lambcrusher's giving you good advice on some trouble shooting...that'll help you decide which option that Beno laid out is best to follow...
 
Yeah! On 7th and the frontage road. I got really excited when I saw your rig and lost all my manners - thanks for being cool. You've got a super sweet setup!
Yup Big Red has that affect on the ladies:grinpimp:. Actually the opposite is true, it's mostly guys that stop and want to talk about the truck. We were just leaving kababalicious when you pulled up. We figured we deserved the break after kayaking all day. We're gonna get your rig set up to make that trip to big bend. I haven't been yet and am excited about it.

Before you pulled up there was a faded brown 60 that turned right at the light before. I guess the east side is where all the cruisers heads are now.

and your manners were fine.
 
Back
Top Bottom