Lockers In HI?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 29, 2009
Threads
3
Messages
57
Location
Toronto, Ontario, Canada
Is there a mod to allow the elockers to engage in HI range? Or is this just a silly idea?

I know it's an easy thing to mod an FJ Cruiser to do this.

The reason I ask is my LX450 is stuck in HI range. I disconnected the shifter from linkage and the shifter isn't stuck, so I am still troubleshooting. This would be good in the mean time.
 
Not in HI until he adds the pin 7 mod:D

Wrong. The 7 pin mod allows you to NOT lock in low range. The CDL switch allows the CDL to be locked in High.
 
Adding a CDL switch is the way to go but just in case you didn't want to do that for some reason, there is another way. Go to the elocker ECU and ground the wire that goes to Pin 15. On a '97 it's a pink wire with a black stripe. Just cut the wire far enough back, strip the end coming out of the elocker connector and connect it to a ground. This mod will tell the elocker ECU that the CDL is locked at all times allowing you to actuate the lockers in high or low.
 
Adding a CDL switch is the way to go but just in case you didn't want to do that for some reason, there is another way. Go to the elocker ECU and ground the wire that goes to Pin 15. On a '97 it's a pink wire with a black stripe. Just cut the wire far enough back, strip the end coming out of the elocker connector and connect it to a ground. This mod will tell the elocker ECU that the CDL is locked at all times allowing you to actuate the lockers in high or low.

That is a good option, thanks.

I will most likely add the CDL switch, and do the pin 7 mod. I believe if I add the mod WarDamnEagle detailed, I should be able to have full control of all lockers in LO or HI.

I think lockers in HI is a good option for my wife. I'd prefer she just have to turn a switch to engage the lockers to help get out of a snowy ditch or likewise. If she was ever in this situation, I'd imagine she would be worked up a bit (heck, I would be), and may not remember to shift to N, shift to LOW, to engage the lockers.
 
That is a good option, thanks.

I will most likely add the CDL switch, and do the pin 7 mod. I believe if I add the mod WarDamnEagle detailed, I should be able to have full control of all lockers in LO or HI.

I think lockers in HI is a good option for my wife. I'd prefer she just have to turn a switch to engage the lockers to help get out of a snowy ditch or likewise. If she was ever in this situation, I'd imagine she would be worked up a bit (heck, I would be), and may not remember to shift to N, shift to LOW, to engage the lockers.

If you add the CDL switch and do the pin 7 mod then there is no reason to do anything further.
 
If you add the CDL switch and do the pin 7 mod then there is no reason to do anything further.

Hmmm.

It is my understanding that the CDL switch allows you lock the centre locker in HI or LO via switch, and the pin 7 mod allows you to have the centre unlocked in LO. But what if I want front and rear locked in HI, but with the centre unlocked. That is possible with just the CDL switch and pin 7 mod? It is my thinking that with the centre unlocked, I won't be able to lock front or rear in HI without tricking the elocker ECU.
 
Last edited:
Rear and front diffs will only be locked if the center is locked.

With CDL switch, (in hi or lo) lock center ›› turn dial, engage rear locker ›› turn dial one more click, engage front locker.

Try this: with all 3 lockers "on", "unlock" your CDL at the switch; your front/rear indiv lockers will not be locked. However, if you "lock" CDL again (without turning your rear/front locker dial from being locked), they will be locked again.

For rear/fronts to lock, they need to "see" the center locked.

PS, the pin 7 mod also slightly adjusts the shifting points when in 4 lo. Search the earliest thread on this (that was just revived I think last week.)
 
Rear and front diffs will only be locked if the center is locked.

With CDL switch, (in hi or lo) lock center ›› turn dial, engage rear locker ›› turn dial one more click, engage front locker.

Try this: with all 3 lockers "on", "unlock" your CDL at the switch; your front/rear indiv lockers will not be locked. However, if you "lock" CDL again (without turning your rear/front locker dial from being locked), they will be locked again.

For rear/fronts to lock, they need to "see" the center locked.

PS, the pin 7 mod also slightly adjusts the shifting points when in 4 lo. Search the earliest thread on this (that was just revived I think last week.)

But, if I do the pin 15 mod as WarDamnEagle described, then the ECU would think that the centre is in fact locked. This should allow the front and rear to lock regardless of whether the center is in actuality locked. Or I am missing something.
 
But, if I do the pin 15 mod as WarDamnEagle described, then the ECU would think that the centre is in fact locked. This should allow the front and rear to lock regardless of whether the center is in actuality locked. Or I am missing something.

Yes, what you are missing is max traction, or sometime just traction. Your wife may not be able to get out of a snowy ditch without the CD locked. Bad thing like rolling down could happen when you are on a slope and CD is not locked.
 
Yes, what you are missing is max traction, or sometime just traction. Your wife may not be able to get out of a snowy ditch without the CD locked. Bad thing like rolling down could happen when you are on a slope and CD is not locked.

Yeah, but with the CDL switch it is possible to lock the centre as well. It's only the shifting to LO I would like to avoid for her. It's easy enough remember how to press/rotate buttons.

The locked options should be, with CDL switch, pin 7 and pin 15:

C
C+R
C+R+F
R
R+F

in HI or LO

I guess the only thing left out is just F and F+C locked. No big deal.

I am just looking for the most flexibility.

This is a real concern to me as our plans are to move to our cottage in a few years. There is fairly steep driveway (most of it shared by others living there year round) which could be tricky in the winter. I am probably only planning for that one day in ten year occurrence.
 
If you "fool" the ECU into thinking CDL is locked by grounding pin15, I would bet you will permanently (until you unground the wire) have ABS off as well, something to think about. Personally, I would just go with the CDL switch and pin 7 mod. Can't think of a compelling reason to lock front/rear without CDL, to make ABS (semi) permanently disabled. AFAIK, if you have CDL unlocked and rear locked, as soon as one front tire looses traction, all power will go to spinning one front tire. If there is some compelling reason, I would put a switch in to ground/un-ground the pin 15 wire.
 
^ I agree. For the sake of simplicity having a CDL switch + F/R lockers will pretty much get you out of most things. Added more complexity to a system that already performs very well I dont see the point. If my wife is driving mine, the simpler the better.... having to many options for a certain instance doesn't help the case in time of need. just my .02.
 
Good point on the ABS.

When I was looking to buy I could only consider 95-97 LX or FJ due to the requirement of airbags and ABS. I don't know if getting rid of one of them would go over well.. :)

One reason I was thinking to allow F&R locked without C is in the event that the C locker fails. Since no C locked means no F&R lockers, the pin 15 mod solves this, but ABS is lost. Sure locked x3 is best, but I'd imagine locked F and R with an unlocked C is better than all 3 unlocked.

Maybe I'll wire a relay to the CDL switch that will put the elocker ECU pin 15 to ground when the switch is pressed. Or maybe there are a spare set of normally open contacts on the switch to do the same. This way whileI will always have to have the C locked to lock F&R, at least I can have F&R still lock in the event that the C doesn't for some reason.

Ha, methinks I am overthinking this whole thing. Thanks for your patience guys! :)
 
...
Ha, methinks I am overthinking this whole thing. Thanks for your patience guys! :)

Agree.:D

Your time would probably be better spent showing, giving your wife some seat time with the features of the rig. You may want to experiment, get a feel for it yourself first to avoid embarrassment and/or confusing her?:o

Depending on the conditions a fully locked rig can make you look like a hero or get you in bigger trouble. Reading about it is great, but in the end seat time is the only way to know what "feels right" and the correct action to take for the conditions. Plus, if your in a safe place (where there is little danger of rig damage, etc) and preferably have another rig with for recovery, experimenting, sliding around, getting stick, etc, can be big fun.:hillbilly:
 
Ha, methinks I am overthinking this whole thing. Thanks for your patience guys! :)

Yes, I think you are overthinking it and trying to fix something that is not broken.

This is a real concern to me as our plans are to move to our cottage in a few years. There is fairly steep driveway (most of it shared by others living there year round) which could be tricky in the winter. I am probably only planning for that one day in ten year occurrence.

What are the chances that the one in ten years occurrence will happen on the exact day that your CDL mysteriously fails to work? Not trying to bust your balls too hard;) but no need to fix what ain't broke.

On a steep snowy driveway, you may or may not want to be locked. If it is really slippery/icy, and there is even a slight side slope, being locked will make it more likely to slide sideways at any slight loss of traction. This loss of traction will neccesarily occur in anything but straight ahead driving, when fully locked. This is an advatage to Fulltime 4wd (no CDL), allows slippage in the drivetrain, instead of at the wheels, in those kind of conditions.
 
If you "fool" the ECU into thinking CDL is locked by grounding pin15, I would bet you will permanently (until you unground the wire) have ABS off as well, something to think about. Personally, I would just go with the CDL switch and pin 7 mod. Can't think of a compelling reason to lock front/rear without CDL, to make ABS (semi) permanently disabled. AFAIK, if you have CDL unlocked and rear locked, as soon as one front tire looses traction, all power will go to spinning one front tire. If there is some compelling reason, I would put a switch in to ground/un-ground the pin 15 wire.

ABS is a function of the CDL indicator switch position. Grounding pin15 of diff lock ECU doesn't change CDL indicator switch position, so I don' think this will disable ABS. Furthermore, the front/rear differential lock circuit is isolated from the ABS circuit.
 
Back
Top Bottom