Is my clutch gone?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 2, 2004
Threads
294
Messages
2,745
Location
Hayward, Ca.
I am totally pissed right now.... I sent my dad out to go get me some gas in my 78- fj40 and he comes back with a 40 that does not have a clutch? When we press the clutch pedal in, it goes all the way to the floor. The tranny/ clutch was working perfectly before my dad's little trip :mad: .. I didn't ask my dad what happend( because I was so mad), but he told me that after he tried to start it back up from fueling up, the clutch pedal would just go all the way to the ground?:confused: I dont know, I am pretty sure that the clutch itself is not messed up, but maybe some type of linkage or something that got dissconnected, my question is what should I look for and where? Please any info......P.S. I didn't really look at it because it is dark out now, but I will take a look at it tomm....
 
Last edited:
check out the slave and master cylinders. my slave went out on my wife a few weeks ago and she called me to tell me that the clutch went out. i got pissed, but was relieved when i found it was just the slave. it's an easy fix.
 
Happened to me. I was driving along and all the sudden i couldnt switch gears and the clutch was extremely loose and went to the floor. Turned out the slave cylinder went out. If you can see any leakage inside the car from the clutch or on your dads shoe, then its the master cylinder.
 
saint60 said:
check out the slave and master cylinders. my slave went out on my wife a few weeks ago and she called me to tell me that the clutch went out. i got pissed, but was relieved when i found it was just the slave. it's an easy fix.
What do I look for when checking the Master and Slave cylinder? Leakege?:confused:
 
if the master is leaking you will see it on the inside of the cab where the clutch linkage goes through the firewall, with mine it had leaked down the firewall and actually had taken off alot of paint so it was pretty obvious. if your looking to check the slave cylander i would just look for any fluid on/around it or park it with some cardboard underneath it...with mine i kept loosing fluid as well...hope this helps
 
just looked underneath the cruiser, there is a crap load of fluid on the slave cylinder... How do I go about replacing it? Do I need to bleed the system? How do I do that?
 
cc93cruiser said:
just looked underneath the cruiser, there is a crap load of fluid on the slave cylinder... How do I go about replacing it? Do I need to bleed the system? How do I do that?
Slowly bleed the system using clear tubing and watch it for air bubbles. Remember to shut the bleed valve with the clutch pedal all the way down. Then have your father let the clutch pedal up. Continue the cycle until there are no bubbles and the fluid looks fresh. If your father now feels the clutch pedal engaging the clutch, then your slave/master or both are allowing air into the system past a seal and need to be replaced. I’m not sure how you determine which one it is if there is not a sign of leakage also. I tend to R&R both at the same time. Don't blame your father - when they go out, they don't ask who's driving.
 
Lost Bolt???

If your not leaking fluid, check the bolt that holds the pedal to the clutch slave just inside the cab. lost my clutch on the trail, turned out nothing more than the bolt came out.
 
I woundnt bother with the master.... the master will outlast the slaves 3 to 1... to me that just seems like a waste... in fact if you want to learn more about your truck.... you should buy a rebuild kit for the slave.... it's like 10 bucks, and very easy. alittle scotch brite pad and presto ! good to know if your on the trail...anyways hope this helps
 
X3 on the rebuild, then you can pick up one that somebody else doesnt want to rebuild, put 10 bucks in it and you have a spare, and like said above, it will teach you more about your truck:cool:
 
I replaced the slave on mine a couple weeks ago, it's simple. 2 bolts and the flare nut on the slave, then bleed it, took me about 15 minutes. If you and your father have all the cruisers in your sig line you need to buy some OEM manuals!
 
so here's a question for everyone when you have your foot on the clutch and it's down to the floor and the truck strarts to move with your foot is still down on the floor and the truck in gear what's up with that???

kevin
 
bigbluefj said:
so here's a question for everyone when you have your foot on the clutch and it's down to the floor and the truck strarts to move with your foot is still down on the floor and the truck in gear what's up with that???

kevin


one or both of cylinders is leaking down. sooner or later it/they will totally crap out.
 
Dianna said:
I replaced the slave on mine a couple weeks ago, it's simple. 2 bolts and the flare nut on the slave, then bleed it, took me about 15 minutes. If you and your father have all the cruisers in your sig line you need to buy some OEM manuals!


I do have FSM's for most of them, including the 40 I am going to work on, I just wanted your guys' input before I begin with the work, that's all ;)
 
Back
Top Bottom