Intake Hose Crack

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 16, 2008
Threads
31
Messages
365
Location
Longmont, CO
Just wondering what kind of impact this crack would have on performance. I'm gonna say this thing is at least PI (half the circle) in length. I thought I saw a thread that said it is a source of rough idle. I found it while I was searching for why my truck rattles in drive; which is what I do with all my free time lately. Who won the election? I was looking for the source of my rattle.

Anyway, will this really make the beast idle rough? And, it doesn't seem possible but, could this be the source of the rattle? That thing is relatively hard plastic.
DSC_0485.webp
 
The engine will run lean and the EFI computer will be all over the place trying to adjust fuel ratio.

You are introducing unmetered air into the engine.

In it's original state the hose is not "relatively hard plastic". It's actually very pliable.
 
Until you can replace I found that wrapping it with saran wrap THEN wrapping with duct tape sufficed until I replaced it. Duct tape alone didnt work for me.

ONLY a temp solution.
 
I had a crack in mine, and I was stalling all over the place. The RPMs start bouncing insanely. I'd replace it. I tried duct tape, but all i got was a melted duct tape smell through the vents and the same problem. It IS still possible to drive it, but it is a pain at stop lights.
 
I used electrical tape wrapped in duct tape around a few sections of baling wire and wrapped again with duct tape just for good measure...



until I bought a new hose from CDan...

taping is only a temporary solution -- it needs to be replaced.
 
I used electrical tape wrapped in duct tape around a few sections of baling wire and wrapped again with duct tape just for good measure...

...

Outsider art.


I did the same. You'll be amazed how much better your truck will run without that hole sucking in unregulated air. Mine was far-gone, so I eventually ponied up for a used on here on 'Mud. Sprayed the new unit inside and out with silicone, let it sit overnight, and stuck it on. Works great.
 
So CDan - What's the damage on these?
 
~100 bucks list.
17881-66060 (applies to your 94).
 
Last edited:
Outsider art.


I did the same. You'll be amazed how much better your truck will run without that hole sucking in unregulated air. Mine was far-gone, so I eventually ponied up for a used on here on 'Mud. Sprayed the new unit inside and out with silicone, let it sit overnight, and stuck it on. Works great.

I thought silicone getting sucked through an engine was bad on O2 sensors
 
I'd use Shoe-Goo on it, after cleaning it well. Tough as nails and sticks extremely well to vinyl and rubber. You could use a urethane caulk, too (PL series from Home Depot) - just don't get it on your hands or your hootus.
 
Ditto on the rough idle, stalling etc.

Call Cdan now and get it replaced. Simple 10 minute job...even for me. :banana:
 
i used some kentucky chrome on mine at first (duct tape) and it held. Eventually got a new one. Truck runs MUCH better with a proper fix.
 
i used some kentucky chrome on mine at first (duct tape) and it held.

That's funny. Duct tape is in my near future. Like I said, just boppin' along looking for something loose and saw that hose. I'm glad to hear that it is significant and simple. I called CDan but he is OOO today and back tomorrow. I am making another list however. I've owned it 2 mos now and have been going through it. Tomorrow I order:

o New Intake Hose
o Cap
o Rotor
o PCV and Grommet
o Plug Wires as they have been pointed out are the originals

I have an appointment tomorrow at Slee to have the Tranny flushed so I'll wrap that thing up. I am a 1E-06 :banana:guy but I've had fun doing the Power Steering unit, belts, fluids. Thanks for all the feedback. Quite the site we have here.

Paul
 
Yeah, mine cracked in the same place. They bake themselves brittle over the engine, then you go to do service, and they pop there at the accordion.

I made a real elaborate "fix" for mine, then found undesirably high silicon (dust) readings in my used oil analysis.

Only thing to do is bite the bullet and get a new one.

It should theoretically stay flexible for years before it bakes brittle again.

Just my $.02
 
I have a used, but not cracked, intake hose from my 94 sitting around. FREE + shipping if anyone wants it.

Would love to have it shipped to 30019
 
Yep, what Dan said. Get a new one as soon as you can. Wrapping helps to a certain extent then it goes south; eventually. Here are some pix of mine. I crazy glued/JB welded the crack before wrapping.

attachment.php
attachment.php

attachment.php


Then I got a new one from Dan (about 8K or so miles ago) and ever since things have been groovy :D. All the little idle burps and jumpy taco have been gone.
 
So I got a new one and installed it. Also replaced the spark plug wires, cap, rotor, PCV/grommet. Much, much smoother ride. Very happy. Even a 1e-06 :banana: guy like me can do it.

After reading about the innovations that many on this board have done to extract the PCV grommet, I approached that with great care. I lifted the lip of the grommet and tried to get a needlenose under and clearly that was a bad idea. So this worked:

1) I put a vertical slit in the thing the whole lenght of it
2) Stuck a screwdriver into the meat of the grommet and lifted it up. It separated at that slit and I was able to get the neednose on that piece and started peeling that grommet away like a tangerine.
3) The bottom 1/3 of the grommet was staying down there and it was starting to concern me but with about 2/3 of the top "peeled" away, the structural integrity of the bottom was gone and could just sort of "collapse" the inside of the grommet pushing with the top part that was still attached.
4) It all came out in one piece.
5) I looked in there and there was grommet dust in there and while it wouldn't have mattered I'm sure, I stuck the mouth of the vacuum over it and it pulled it out.

I stuck some BG44 in it and drove up to the gas station to top it off and it was dramatic how much smoother it was. I'm pretty damn happy.
 
Back
Top Bottom