Install rear e-locker on a 96

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Romer

fatherofdaughterofromer
Moderator
Joined
Sep 14, 2003
Threads
560
Messages
11,998
Location
Centennial, Colorado
I read Boston's (Kevin) excellent write-up at:
http://www.yankeetoys.org/mangler/elockerinstall.htm

And I have a few questions. This is for Sarah's (ROD) 96 LX450.

I will be installing a rear e-locker along with swapping out the short side axle. I was thinking about the wiring and routing wires. I know Toyota builds one main harness that fits different vehicles to reduce inventory costs.

So I have the following questions:
  • Is Kevin's write-up the same for a 96?
  • Can I wire all this up for a rear locker only? Then add the front locker later on?
  • Anyone have a switch, ecu lying around (oops wrong section - moderator!)
  • Is there an easier way to wire this up? I like using the dash lights because knowing kids they may forget it is on without the light to tell them.
  • Any other pearls of wisdon would be appreciated.
 
Are you saying that I don't need to add the bulbs, ECU or in wires inside the cab?
 
You will need to add the rotary switch, lock ECU and the indicator bulb(s).

When I did mine several years ago I did the rear first and ran it that way for a couple years before I did the front. The forward cowl harness has all the bits needed for the switch and the ECU. I understand that the Lexus will not require a floor harness to make the trip up to the instrument panel. In order to make it a plug-and-play you will need the harness that goes from the rear axle to the left quarter and possibly the rear sill harness. I will need to research the part about the sill harness. Modifying the rear axle housing is easy and the diff drops in.
 
Sorry for the confusion. You still have to add bulbs, ECU and switch. As for wires, Kevin ran from rear axle to the front DS kick panel. For LX450, you have to run from rear axle to the DS rear QP only, the 5 wires that run from DS rear QP to front kick panel are included in your stock harness (but not in Kevin's stock harness).
 
Thanks. Do you know where in the qtr panel it is?


I have made a hard decision. Rather than buying Sarah a used rear short axle with questionable heritage, I will give her my rear short side axle:idea: . I mean, thats what fathers are for, right?

Guess I'll have to look at buying the harder set of rear axles that just came on the market. The sacrifices:D

Since I am tearing down the axle this weekend to pull the diff for re-gearing, now is a great time.
 
Ken,

Let me jump on this thread and give you my experience. You have an LX 450 just like mine. This came from the factory with the complete locker's wiring harness from the Driver side left kick panel all the way to the rear quarter panel located under the jack mount. You will need to make the 5 wiring harness which is about 12 inches long or get this one from the boneyard/junkyard (which is what I have done). You will either have to unplug all connectors (abs, rear DS light, and locker) and disconnect the clear plastic tube located under the jack stand or stab a hole (using a pick or scratch awl) through the rubber grommet and pass the 5 wires through the hole and insert them into the male connector. It is up to you which route you choose. You also need to get the wiring harness with ABS from the axle up to the rear quarter panel where you will hook it up to the connector you have just added.

Like CDan said, you will need the bulbs in the dash, Lock ECU, Diff lock rotary switch, and wiring harnesses that I mentioned above.

If you decided to add the front locker later on, then all you need is the locking axle and the harness that goes from the front axle to the passenger side fender inside the engine compartment below the antenna's mast.

I need the locking diffs/axles to complete this mod. Have I confused you?
 
And if it were me I'd install the front locker bulb while you were in there this time.
 
You also need to get the wiring harness with ABS from the axle up to the rear quarter panel where you will hook it up to the connector you have just added.

Can you expand on this? It already is hooked up somewhere.

Thanks for all your inputs. I guess this is one nice thing about owning a Lexus:D
 
Ken,

Follow this thread below and you will see the axle harness that I mentioned on my previous post.

https://forum.ih8mud.com/showthread.php?t=120638

Wait a mnute, you have a locked LX, all you have to do is compare ROD's on yours side by side and see what you need to lock her rig up. :grinpimp:
 
Here's a picture of where the rear sill harness connects to the final harness from the sill to the actuator. If you look behind the plug I am pointing to you can see the grommet where the sill harness exits the jack/tool kit cubby and runs along the rear sill. You need to remove the spare tire to get a good look at it. The harness that is plugged connected it the non-locker sill to actuator before I added the final locker harness. So, you remove the one that is plug in (as in the picture, ABS) and add the harness that has both the ABS plug and the Locker plug.

Once you have the sill to actuator harness it will become clear.
Sill Plug.webp
 
Last edited:
And like others have said, If I can't find it, look under my truck. Thanks for the picture thats awesome.
 
Jus an update. Locker in. Lights blink. Only problem is something I missed in what you guys were telling me. I had the Rear Locker Harness and did not realize I also need the Rear sill harness. So a quick look to see if anyone has one and then likely make my own sill harness.

Any tips from the guys who have made their own harness?
 
Ken, my father & I just made our harness yesterday for the wifes 96LC.

Dad used the ends we got from Cdan, sodered(sp?) them on both ends & added this harness down the entire length of the DS of the rig. Turned the switch & fully functioning Elockers retro fitted!

Make sure to get the factory splices from Cdan & the connectors it will make the whole job easier. Not to mention cleaner.
 
You don't need the entire sill harness only the five wires that go from the end of the main harness under the jack holder, I have photo if needed, to the final, or sill to carrier harness.

Does this make sense?
 
You don't need the entire sill harness only the five wires that go from the end of the main harness under the jack holder, I have photo if needed, to the final, or sill to carrier harness.

Does this make sense?

It makes sense. I want either the harness or to make one with the correct connectors. Didn't know you could order the pigtails from Dan.
 
Ken,

I can't recall what the connectors look like other than they were like small needles and I just pushed them into the factory connectors on each end. I just stripped them from another section of the wiring harness bits and pieces I had laying around but I know you can get them from CDan. I put them in piece of 3/8" flex loom and ran it beside the factory harness. It really isn't that bad.
 
This picture shows where the main harness and sill harness connect. I can't recall now if my none locker main harness had both plugs or just one. I think it had both but one was missing the wires for the locker. Anyway I can check when I get back in town and I should be able to tell you which wires are for the locker. You may be able to to tell in your Lexus becuase on plug (main harness) should have the connections and other (sill side) will not.

In any case you need to bridge between this connection and the one that exists on the sill to locker harness that runs along the DS frames.

Hope this help
IMG_1098.webp
 
Back
Top Bottom