help with bellhousing

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 31, 2005
Threads
28
Messages
129
Location
puyallup wa
:crybaby: this thing is pissn me off, been wrenching on it all day, anyone have tips for an easy removal, i cant seem to get the two bolts inside of it off becuase they back out and hit the flywheel, and now i notice there are more bolts on top :crybaby:
 
just pull the flywheel off, in fact i'm pretty sure you need too anyway.
keep in mind there's a rear set of motor mounts on the bell....
 
yeah i need to pull flywheell of anyway, but now i have bigger problems!!! every bolt on the flywheel busted off!!! what do i do now, they were in there so tight or somting that they all busted right where the threads begin on the bolt. i guess i will try an easy out, but i doubt that will work. anyone have success with redrilling and taping to a larger size? crap i dont know what to do! i am so pissed
 
You'll need to pull the crank and put a bit of heat on them - they may have been loctited in.
If you drill a hole through them this will help.
(this is why you need to pull the crank - the other end of the bolt is open to the inside of the sump).
 
can i pull the oil pan and get to the onther end, or does the crank have to come out? and as far as heat goes all i have is a propane torch, this isnt hot enough is it.
 
If you can, do the welded bolt/nut onto broken bolt trick along with some heat. That'll give you another head to put a socket on. Good luck man. I'd try everything possible before pulling the crank, and don't put too much heat on there, just use enough to do the job. Can you post any pics, I gotta see these broken flywheel bolts.
 
here are some pics of my disaster, you can still see the remaining threads in all of the holes, and only two broken bolts were left under the truck, all the others went flying into space :rolleyes: . im going to try and heat them and use an easy out to getem out, but if that doest work i will drop the pan and take a look. the only problem is i dont have anymore money to get the stuff, and i dont know when i will get paid, thats the problem when you work for your dad and your 15. :grinpimp:
IF ANYONE HAS ANYOTHER SUGGESTIONS ON HOW TO GET THEM OUT i would appreciate it. thanks!
bolts1.webp
rear1.webp
 
Chances are the threads are not rusted. Instead they may have some kind of thread locker or epoxy on them so heating them to about 400F (and an EZ out) might work. If not, weld a nut on to the remains with 7018 electrode and crank it out while still hot. Use the front nut for the ground clamp as you don't want the welding current passing through the bearings.
 
That is one FAWKED UP situation. I wouldn't wish that on ANYBODY. :eek:

I thought it was bad when I had ONE bolt break at the shop 12 years ago. In fact it cost me a friendship. See, my friend broke the bolt while trying to help me out, then proceeded to break off an easy-out inside what was left of the bolt.

After he left [never to return] I took a very, VERY small drill bit and drilled a crescent around the easy out [luckily he hadn't drilled exactly in the center of the bolt either. One hole of the crescent was close enough to the threads of the crank to release the pressure.

Make sure once you get these out that you pay attention to the factory specs BEFORE you put a fresh set of bolts in [which is something the PO prolly didn't do :mad: ]. IIRC, the torque is something like 37lbs.
 
haha, i have removed them. AMEN! now to find new bolts to replace them with. maybe some grade 8's ? so torque them to 37lbs with some rvt, and perhaps a drop of locktight?
p.s. thanks to everyone for their insight!
 
NO RTV!! NO LOCKTITE :eek: :eek:
 
staplebus said:
haha, i have removed them. AMEN! now to find new bolts to replace them with. maybe some grade 8's ? so torque them to 37lbs with some rvt, and perhaps a drop of locktight?
p.s. thanks to everyone for their insight!

STOCK, from dealer or cdan, but always stock. They are supposed to be used only once anyway, torqued correctly, and disposed of when removed.
 
SpaceGhost said:
They are supposed to be used only once anyway, and disposed of when removed.

opps.......twice....
 
Back
Top Bottom