Head Gasket shot. Committed

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Pull the plugs. Label them. Post pictures.

For some reason everything you've described reminds me of boats that sat a long time with ethanol gas. They would pull a huge slug of water from their tanks and stall out. On restart we would see white smoke/steam.

I'd drain all the fuel lines and the injector rails, dump all the gasoline. Use it in a weedwhacker.

Water in the oil - 1 year of sitting...could be a number of causes. If you can, do a leakdown test and or check compression. Send a sample of that oil to blackstone.
 
Again, I would just start w rad cap off, and see if it blows coolant out.

If so, then drain oil, squeeze some into cyls thru plug holes, and figure it is head gasket.

Water in the oil eats crank bearings.

Heads and valve seals are cheap nxt too doing bottom end and crank seals.
 
Pull the plugs. Label them. Post pictures.

Send a sample of that oil to blackstone.

Agree on 100% posting pics of plugs, but spending money on a Blackstone on that old black-ish oil is dumb money.

Send Blackstone some fresher oil from a fresher change with a filter, even cheap Valvoline or whatever - give them oil that if it has migrated water, it’s not from a year of condensation cycles, it’ll be from a real HG issue if you don’t see that clearly in the #6 plug being cleaner than all the others.

#6 sparkplug up by the firewall is where we all see failure fron original HG design- so if it’s that, it should be obvious before you buy Blackstone oil results.

That’s my vote / what I’d do.
 
Only one oil change and not many miles since it sat so long could cause the water in the oil. There is no way to get every little bit of oil out when you drain it. Some left in pan and pump and pick up tube and on top of head. I bet running it a couple hundred miles and then another oil and filter change and the water in the oil will be gone.
 
So my morning will be a bit different than originally planned.

1. Replace plugs, take pictures, post. Looking at plug 6 will be interesting.
* If obvious then HG time *
2. Install new plugs & wires (I have them already)
3. From under rear seat siphon gas and avoid neighbors reporting me to code enforcement (EPA)
3A. Put in a couple gallons of ethanol free along with some lucas injector cleaner.
4. Install fuel filter (I have it already)
5. Put in new oil and filter (have filter, go buy some oil)
6. Start it up with radiator cap off and see if coolant blows out

I'm sure that somewhere in there I'm supposed to do a Hail Mary and an Our Father.

Will report plug pictures soon, then results later on.
 
FWIW when mine had bad HG- with the oil drained in garage- oil plug out- it continued to seep coolant out the oil drain- for days after onto the cardboard- drips - Im sure leaked into cyl-past rings out drain hole.
 
Just a few ideas:
You can drain off the bottom of the tank by carefully removing the plug on the tank and reinstalling it. After the water/ethanol mix (which is on the bottom) is removed you need to add some 91 with ethanol to bring the octane back up to 87 and help disperse any remaining water in the tank/lines. Removing the fuel pump access cover and inspecting tank is also a great idea to verify condition of tank and pump assembly. I would also replace the fuel pump strainer while doing so.
 
So my morning will be a bit different than originally planned.

1. Replace plugs, take pictures, post. Looking at plug 6 will be interesting.
* If obvious then HG time *
2. Install new plugs & wires (I have them already)
3. From under rear seat siphon gas and avoid neighbors reporting me to code enforcement (EPA)
3A. Put in a couple gallons of ethanol free along with some lucas injector cleaner.
4. Install fuel filter (I have it already)
5. Put in new oil and filter (have filter, go buy some oil)
6. Start it up with radiator cap off and see if coolant blows out

I'm sure that somewhere in there I'm supposed to do a Hail Mary and an Our Father.

Will report plug pictures soon, then results later on.
Start it and let it warm up to operating temperature and then pull the drain plug with it warm. Let it drain while you change your plugs and fuel filter and everything else. Install plug and oil filter and fill with oil last.
 
Step one from my list above. Plugs are out, I don’t see anything wrong with them. No sign of being steam cleaned on number six.

BBF3520F-7CB0-465A-A09E-4D20EECCF5C8.webp
1C8DEA67-76FD-421B-80BA-89CABE210F4D.webp
80AAC56E-5EB7-475D-BDEB-89B83D8C78EA.webp
AC8E2556-9E6D-494E-8DB4-F3A62342DF1F.webp
 
#1 looks a bit wet. Is that oil on there? From the pic it even looks like it is "holding" onto the electrode like water would.
 
Last edited:
#1 looks a bit wet. Is that oil on there? From the pic it even looks like it "holding" onto the electrode like water would.
#1 makes sense with 0301 code. I will look closer to see if it is oil or water.
 
#1 makes sense with 0301 code. I will look closer to see if it is oil or water.

Could also be fuel - If that plug wasn't firing you could (I think) get a 301 and a wet plug. Could also be an injector stuck open.
 
No matter what, at least you know now that #6 plug where they normally blow the original design HG isn’t a clear issue.

I’d proceed with a cheap oil change and new filter, and when you do drain the oil push a little fresh in until clean oil comes out the drain - both because water is heavier than oil plus I’d want ALL the old dark oil out in this swap.

I used to buy a quart of just cheap $hit oil I did this with using 1/2 the quart each change on a old BMW of mine, just to force out that last remaining dirt & sediment oil. But that motor was also over $10K to rebuild if you spun a crank bearing, or ate valves in the head (S14).

But back to yours, that hard slug of cold thicker oil should push the last of the water or thinner/warm brown oil out so you get a full flush of old crankcase fluid, water or oil.
 
Good tips so far.... spare the weedeater from the bad gas though :) Take it to the hazardous waste recycling place.
 
Update:
Siphoned all gas, dried out tank completely. No rust visible with camera anywhere. Gas didn't appear to have water but it's hard to tell with as much as I siphoned off. Cleaned up the pump and the sock was discolored but overall clean. Replaced it anyways. Put that back together.

While taking out plug #6 the heater control valve brittle plastic gave way and... Luckily I had a new spare. Just finished putting that in. New plugs and wires are done as well.

Next step is to take out the fuel filter, not sure if I'll get to that today as I'm on some conference calls for the next few hours.

So tomorrow morning replace the fuel filter, put in the new ethanol free gas, some lucas injector cleaner and some distilled water to top off radiator. Then start it up and see what happens.
 
Search ‘slotting fuel filter mount’ - if you want to save some time.

Also makes it a snap if you ever revisit the filter for whatever reason.
 
#1 sure is wet. If that is fuel I'd inspect the injectors.
 
#1 sure is wet. If that is fuel I'd inspect the injectors.
Not sure how to check injectors.

All plugs smell the same. Could have a fuel smell on #1 but I can’t tell now.

I’ve got a few yards of extensions. I’ve done the fuel filter on other 80’s. Hard to reach but I’ll get it knocked out in the morning.
 
This thread is like Groundhog Day for me. All the same things I was seeing, except my code was P0306 and my stumble was at idle. I was getting latte froth in the catch can and seeing random temp spikes. I got lucky and never saw water in the oil, just exhaust or compression gases in the coolant.

I used Blue Devil head gasket sealer and it cleaned up the idle code and truck still consumes a bit of coolant, but not enough to want to stop wheeling it yet ... YET. The water pump gasket failed the day after the Blue Devil treatment, but not sure if that was a result or if it was done beforehand and just finally quit.

What I have since realized is that I likely have a broken chunk of CAT that clogs up the exhaust when cold and that is what likely started the whole mess. Once the truck is hot, I can hear it rattle around and it holds temp at 190*F (with the 2nd CAT removed) with zero issues. If I start it cold and hit the highway for 10 miles, the temp will spike until I pull over for 1 min to let it settle. Not sure if this helps you at all, but can't hurt to make sure the exhaust is clear.
 
Back
Top Bottom