Hard Top removal???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

The first time I took the top off I did it by myself. I would not reccomend that method.
 
The second time I tried to do it a different way (rolled end over end backwards at 60MPH.) Only about 1/2 of the top came off. I would not reccomend this method either.
Rob M Concord, MA
 
stayalert said:
The second time I tried to do it a different way (rolled end over end backwards at 60MPH.) Only about 1/2 of the top came off. I would not reccomend this method either.
Rob M Concord, MA

Dang Rob - you are going to succeed simply by finding all the ways you would NOT recomend!
 
freightdog said:
"6- Remove bolts on the outside above the windsheild"

Where are the bolts? Pictures please - the PO used great stuff across the top of the windshield????

Dawg,

Here you go:
top bolts.webp
 
freightdog said:
Thanks Pablo -

Mine is covered in Great Stuff foam all sculpted out -

Time to get the pairing knife out!

Jeff

Aw man Jeff, and I thought I was gonna have all the fun this weekend w/ a t-case input seal replacement and oil pan gasket replacement.

Sounds like you got me beat!

What the heck is Great Stuff?

Pics?
 
There were supposed to be bolts there?!?!?!

I took my hard top off about a year ago (me and 1 friend) and it's been in the shed ever since. I took it apart with the intention of redoing all the seals and stuff, but... I now have a soft top on it and a bikini for summer. I'm still trying to get the hinge pins out of the door hinges (they've been treated with Break-free every day for weeks and won't budge.
 
Product Usage
A multi-purpose formula, GREAT STUFF™ PRO Gaps & Cracks is perfect for filling gaps and cracks ranging from pipe penetrations and electrical outlets to telephone and television cable entries. All GREAT STUFF products are polyurethane-based and offer superior performance advantages over latex products

Guess he took this serious! :beer:
 
badkarma said:
There were supposed to be bolts there?!?!?!

I took my hard top off about a year ago (me and 1 friend) and it's been in the shed ever since. I took it apart with the intention of redoing all the seals and stuff, but... I now have a soft top on it and a bikini for summer. I'm still trying to get the hinge pins out of the door hinges (they've been treated with Break-free every day for weeks and won't budge.

Use an air hammer...
 
I have a method for 1-person removal/reinstall similar to IDave using a come-along instead of the engine hoist. Have not set up in my new garage so I don't have pics, but its easy and works great. Hope my description gets the point across.

Suspend a pulley from the bottom chord of the trusses directly over the center of the roof.
Put a stout eye-bolt into a stud in the side wall.
Thread the cable of a 1-ton come-along over the pulley and attach the handle end to the eye bolt.
Attach a sport/roof rack to the rain gutters (I have a Yakima with steel pipes for the cross-bars).
Tie a knot in both ends of 2 ropes leaving a loop at each end.
Put the loops over the ends of the racks.
Clip the middle of both ropes into the unattached end of the come-along cable.

Remove the bolts from the top and crank away on the come-along. Make sure the racks are positioned so the top is balanced as you lift it or the locating pipes can scrape the paint as it comes loose. Works great if you have a fairly high ceiling in your garage and leaves a free hand for a beer!

I hang the hard top from the trusses during the rest of the summer. Back under it and lower into place in the fall.

Cheers,
Nord
 
Well I just put mine back on (easier than taking it off!!!) two man job as long as they're not sissies just picked it up walked it over got it close to the right position and set it down resting on the two alignment rods in the front and the rear was sitting on my two open half doors in the back then I got inside lifted it with my shoulders walked it into place as my buddy aligned everything (seals and sluff)then I set it down SLOWLY, wiggled everything into place and put all 4 of the bolts back in...hehe
 
Does anyone have any pics of how to create a hoist in the garage. I see the two above in this thread, but was looking for any other ideas? For instance, maybe a hoist in the garage, that is on rails and allows the top to be slid down the wall of the garage?
 
I know its ilegal... I have been stoped once and i told the cop that a license plate light was not mandated untill 1970. He ate it right up. Got to love the the 22 year old cops
 
So I took my hard top back off and it's off for the summer this time....I did it alone also by taking it apart piece by piece because I plan to but new bolts in and replace all the seals...my question is

How do I remove the back section where the rear hatch hinges and the Hydrulics <---misspelled mount ....it't attached to the lid somehow I've removed all screws and bolt but cant get it off...heres a pic


or two



Or three

 
Back
Top Bottom