Fried a 1FZ-FE

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I've seen a lot of post lately talking about how these engines are good for 300,000 miles before overhaul. After looking at these pics I have only one question. Why only 300,000?
 
I have a question as to the sizing of the ROD bearings. I have my '93 torn down and am trying to decipher the bearings so that I can order replacements. In the manual it says that the rods have a number on the side where you can add that to the number on the crank to get the proper bearing. The only number that I can see on the rods is a "cast" number on the bottom of the main cap, is this what I am looking for?

I am planning on dropping the block off to be cleaned and not Vat'd, then to bore/hone +1mm over. I called a local shop to see if I can order a replacement "custom" UB2710 but the fella that answered the phone said they DO NOT sell parts and only rebuild engines... With that said I am trying to save my bearing by not Vat'ing it and cleaning it REALLY good before assembly.
 
This is 1FZ porn in it's best form! I have never seen pics like this of the mighty 1FZ before, and have gotta say i'm impressed. Makes me not want to sell my ever-reliable petrol girl now!
We all know these motors are bulletproof and most of these pics back that claim up! God job guys, cheers for sharing the pics. :clap:
 
I've seen a lot of post lately talking about how these engines are good for 300,000 miles before overhaul. After looking at these pics I have only one question. Why only 300,000?

Toyota design specs. called for 300,000 kilometers not miles before a bottom end rebuild.

Why? Probably because of engine wear.
 
Toyota design specs. called for 300,000 kilometers not miles before a bottom end rebuild.

Why? Probably because of engine wear.

I thought it was 500,000 Kilometers, which would be near 300,000 miles. And that's with average care and feeding. I'll bet those increase by 50% at least with the type of care the motors get from most MUD members.

If I project the miles I've driven the 80 in the last 10 years over the average life expectancy of a human my age, I may not find out how far it will go before rebuild! It will take me 40 years to drive another 200000 miles.
 
Last edited:
It will take me 40 years to drive another 20000 miles.

Either you dropped or added a zero somewhere or you are only driving 500 miles each year. (6 years between oil changes. ;))
-B-
 
I'm at 210k, with the original HG, runnin' like a top. Maybe the 189k mile rebuild interval is to deal with oil leaks. :eek:

Based on the few head gaskets that I've seen on engines with higher mileage (over 140kmiles), its safe to say that your HG is actually seeping coolant out. All of the composite HG's are showing combustion ring deformation and coolant seepage. These HG's were pulled as PM but it was only a matter of short time before they blew. :frown:

Lie under your engine with a flashlight and look up at where the head meets the iron block on the exhaust side. See if you see evidence of dried up coolant. Do the same for the intake side, though it may be a little tougher to see this interface with all the crap that's hanging on that side! You may even be able to see little fuzzy protrusion in the interface area and that's the HG material slowly oozing out.
 
Either you dropped or added a zero somewhere or you are only driving 500 miles each year. (6 years between oil changes. ;))
-B-

What's an order of magnitude between friends? Thanks, B.
 
I thought it was 500,000 Kilometers, which would be near 300,000 miles. And that's with average care and feeding. I'll bet those increase by 50% at least with the type of care the motors get from most MUD members.

If I project the miles I've driven the 80 in the last 10 years over the average life expectancy of a human my age, I may not find out how far it will go before rebuild! It will take me 40 years to drive another 200000 miles.

You KNOW that you can't wait to tear into it :D
 
Based on the few head gaskets that I've seen on engines with higher mileage (over 140kmiles), its safe to say that your HG is actually seeping coolant out. All of the composite HG's are showing combustion ring deformation and coolant seepage. These HG's were pulled as PM but it was only a matter of short time before they blew. :frown:

Lie under your engine with a flashlight and look up at where the head meets the iron block on the exhaust side. See if you see evidence of dried up coolant. Do the same for the intake side, though it may be a little tougher to see this interface with all the crap that's hanging on that side! You may even be able to see little fuzzy protrusion in the interface area and that's the HG material slowly oozing out.

Haven't seen any coolant leaks so far though I do not doubt the potential. My hope is that I can go another 100k before I need to rebuild. I would definitely prefer to do the head on my terms.

I'm gonna get under there and take another look.
 
Good to finally see some action on this thread. At first me and seth were surprised at the lack of activity...
We both assumed that internal shots of a 1FZ were not as common as say a 2F.
B2710?? Bushing?? Is this a removable part?
 
We both assumed that internal shots of a 1FZ were not as common as say a 2F.B2710?? Bushing?? Is this a removable part?

You're not the first folks on MUD to take apart a 1FZ. Memories are limited here and people hate to search what has been covered.

The bushing is a non-sourceable part. i.e., you break it, you sources yourself a new block or you know a really, really, good machinist.

;)

Keep it coming. I see one of these bottom ends everyday. But it is still nice to see other ones....

:cool:

-onur
IST
 
I thought it was 500,000 Kilometers, which would be near 300,000 miles. And that's with average care and feeding. I'll bet those increase by 50% at least with the type of care the motors get from most MUD members.

If I project the miles I've driven the 80 in the last 10 years over the average life expectancy of a human my age, I may not find out how far it will go before rebuild! It will take me 40 years to drive another 200000 miles.

Offer still stands CDrew. 2 weekends....that's all that it will take between you and me.

;)

:p

I'll even bring the parts.

;p
 
I love taking the top end of the engine so much that I'm doing it again!!! I think CDrew just oughta come over to my place for a HG party!
 
I love taking the top end of the engine so much that I'm doing it again!!! I think CDrew just oughta come over to my place for a HG party!

You guys are tempting me.

I am going to take Beno up on his offer, just not sure when. We can discuss over an adult beverage in Grand Junction and I'll buy.
 
Thanks for all the comments guys. At this point I am going to buy a used engine. The cost to rebuild this thing is too much. I am probably going to save the engine and rebuild for me to put in my 93, which, by the way, has 340xxx miles and still has the original headgasket, and doesn't burn oil (though it appears to have a few slow leaks, no drips).
 
I love taking the top end of the engine so much that I'm doing it again!!! I think CDrew just oughta come over to my place for a HG party!

Count me in too!
 
Back
Top Bottom