Fried a 1FZ-FE

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I feel I should clarify. The engine had no compression, according to the dealer. I checked cylinder #1 with my rotary compression gage and got 60psi. That may be about 90psi if the schrader valve was installed; that is unacceptable. There was oil that looked like it may have seeped from the headgasket.

I am unwilling to pull the head in the car. I want to be able to check flatness and machine the block if necessary. As for finding the cause of failure, I am purchasing all new hoses and will send the radiator out for pressure check.
 
I would go down the path you are heading..... Pull the head and work from there. If you have to mill it a bunch you can gain some free compression :). You can send out the injectors to Cody Motorsports in GA to have them fully cleaned/rebuilt/flowed for around $80. Worth the $$$.

I too liked the rotaries at one point... until you want a reliable 400rwhp+..... then one looks elsewhere :)
 
I would go down the path you are heading..... Pull the head and work from there. If you have to mill it a bunch you can gain some free compression :). You can send out the injectors to Cody Motorsports in GA to have them fully cleaned/rebuilt/flowed for around $80. Worth the $$$.

I too liked the rotaries at one point... until you want a reliable 400rwhp+..... then one looks elsewhere :)

On the rotaries: speak for yourself, sir.

I don't think the injectors are in need of rebuilding as the car ran flawlessly before this. As for my green LC with 333xxx miles, I'll definately have that done.
 
hey you still wanna sell that old beast?
You think when we get that engine up here we could measure the back of the block and crank and put it into NX?? Putting this spare nv4500 behind a 1fz has been keeping me awake at night.
Think we could do something similar to the isuzu diesel swapper guy...
I was talking to darryl and ryan at the machine shop when I was getting the Cummins flywheel ground, sound like about 20 dollars/hole for a over bore and hone job. Just for the machine work. They could also check the block out, hot tank, media blast, etc.

all up to you.
Let me tell you those cummins got heavy flywheels, it was a work out. The flywheel housing was a pain to get off, and some smart person decided to use 10mm head 12 point bolts on the started. Think they left enough room to get a socked on. NO!!!!!!!! Torch and box wrench time.

lots to show you next time your here...
 
Engine was torn down today. The #3-6 pistons were slightly melted and probably burned the rings.

Needed a factory service manual anyway, this was a good time to buy.

1FZ-FE7.jpg


Nate's "Cruiser" modification to the engine stand

1FZ-FE56.jpg

1FZ-FE8.jpg



Engine on stand

1FZ-FE57.jpg



Beautiful valvetrain

1FZ-FE6.jpg



Secondary oil pan removed. Damn this thing's a beast.

1FZ-FE12.jpg



Looking at the gear drive for the p/s pump and the bottom end


1FZ-FE10.jpg

1FZ-FE11.jpg



Timing chain's automatic tensioner is telescoping, and seemed to be driven by oil pressure. Never seen anything like this. The part that contacts the chain is similar to a SR20DET (and others) but superior.

1FZ-FE18.jpg

1FZ-FE19.jpg

1FZ-FE20.jpg

1FZ-FE24.jpg

1FZ-FE40.jpg

1FZ-FE45.jpg
 
Had to mark the position of the cam drive sprocket because there were 2 positions it could be installed in.

1FZ-FE39.jpg



Here you can see the punch marks on the sprocket and the cam shaft.

1FZ-FE37.jpg



OIL SQUIRTER FOR THE TIMING CHAIN!!!!!!!!!!!!!!!!! WOW!!!!!

1FZ-FE23.jpg



We are now true toyota mechanics. The shirt says so, see?

1FZ-FE26.jpg

1FZ-FE25.jpg



Had to remove this little guy to loosen the cam bolt.

1FZ-FE21.jpg



Removing the cams

1FZ-FE29.jpg



Cam bearing caps. Note the oil groove. I was a bit disappointed that these didn't have removable bearings (Nate says "this aint no series 60 (detroit diesel)). Nonetheless, still superior to most other automotive engines.

1FZ-FE32.jpg



Lifters

1FZ-FE30.jpg



Valves - no damage seems to be done here, will probably have to remove them to confirm.

1FZ-FE59.jpg

1FZ-FE58.jpg



Here's the mode of failre. That's the number 5 cylinder.

1FZ-FE63.jpg



cylinder 4,5,6 with cylinder 4 at the right

1FZ-FE60.jpg


Here you can see the melting of the piston on the left side

1FZ-FE61.jpg



And more melting on the right

1FZ-FE62.jpg



This engine will probably become a development engine for a product that is quite secret right now. At this point it will be cheaper to replace it with a junkyard engine and send the thing on its way. I'll keep this one for later use in my own landcruiser and probably bore it and strap a nice size turbo (for good spool and midrange of corse) on it in the future.
 
Seth, that engine is simply amazing, its the best I have seen to date. I wonder what those HZ and HD diesels are like.
That thing makes my 3F-E look like a joke....
 
Ouch. Expensive lesson on why not to let these engines overheat. It was definitely hot inside #5 combustion chamber!
 
Nice job fellas.

Did you remember to put a service bolt in the exhaust camshaft sprocket? Couldn't tell from the pic.

What causes a piston to melt like this and is the cylinder scored pretty bad?

A great shot of the timing chain and the "slipper guide"..had no idea that thing is THAT long!
 
I dont believe we put a bolt in the exhaust cam sproket, why do you have to do this?

The timing chain assembly is kick ass on this engine. Very well made....

As far as the cylinder scuffing....

When we took the engine out of the car, there was only a little coolant left in the system, like in the bottom of the block. I guess the combustion chambers were not getting cooled enough and EGTs went very high. From the looks of things, past the melting point of the piston material. Still havent taken the rotating assembly out yet, Seth is antisipating cracked and/or missing chunks of piston ring.

We will post pics are things progress.
Here are some more pics we dident post yet....
1FZ-FE44.jpg

1FZ-FE46.jpg

1FZ-FE5.jpg

1FZ-FE55.jpg


There will soon be more...:cheers:
 
Your '93 FSM should have a section where the "service bolt" is needed through the Exh cam shaft is well laid out. The main purpose is this: the exh cam shaft is a two piece sprocket and under spring tension. The service bolt simply prevents one half of the sprocket to unload itself when removed from the engine. The loaded sprocket helps keep the lash to a min and to prevent the exh camshaft from moving axially.

What you can do while the camshaft is out of the engine, is to rewind the front half of the sprocket forward about two teeth and then screw in a metric service bolt through the hole. You'll see a threaded hole in the camshaft sprocket.

Picture

Exhcamshaftservicebolt.jpg
 
thanks for this info. Seth purchased the FSM, but during teardown we really dident open it up to much. We will have to do this when the engine is put back together.

No progress to report, seth went home for the week and has not been around. I dont want to mess with it when he is not here, after all its his engine not mine. I will admit I do stop and look at it quite often, asking the question, "why dosent my jeep have an engine like this in it?"

Thanks for the pic of the cam gear.
cheers
 
Be sure that Seth knows about the B2710 bushing if he plans to have the block vatted.
-B-
 
Could someone please tell me what is shown in the last 2 pics of post #54?

Great thread and awesome pics!

Thanks!
 
Engine oil cooler.
-B-
Oil_Cooler.webp
Lubrication_System.webp
 
Last edited:
Back
Top Bottom