Frame off

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

In my experience rustoleum looks the best, but doesn't seem to hold up as well as the others.

I powder coat everything now, it costs more but in the long run it is worth it.
 
Using POR is the best result when not sand blasting the entire frame, without blasting the frame you miss a lot of the pitted rust which could start lifting the coating.


I like the two part epoxies over the powdercoating myself, although nothing I have painted looks as good as powder coating it holds up better. I now believe unless you get the frame dipped that rust will start traveling under the membrane.






That said it sure looks purdy, keep up the great work................

Rob
 
I am going to use Imron gloss black on my frame with triple hardener. That is after I shoot it again with Imron etching primer with single hardener.

I am interested to see how it turns out...the Imron gloss black with addatives was expensive!
 
Polyeurothane is good for surfaces that need to be pretty and hold up to UV rays, basically body panels.

Personally Epoxy all the way, if you feel good about a base coat of POR15 then thats not a bad idea.

I use epoxies that are rated for lining tankers and very chemical resistant plus hard and flexable. The two part primer is thick and will help displace any moisture left on the frame.

My other favourite feature over powder coating is the ability to properly blend in a section that may need welding then repaint. Powder coating is said to be durable, I found after a couple or restoratons that the Epoxy holds up even better.


Heck, I use to see ship drives with thousands of hours in the salt chuck come up with a heavey epoxy coating in near rust free form, mind you the zincs helped out a lot also.

Then topcoat with Imron for that pretty look and good UV protector for parts of the frame exposed to sunlight.
 
thanks man for the advice....

I am fairly new to painting with a gun and mixing your own and so forth. They sold me the poly obviously due to my knowledge....I told them what it was for and what I was after. The resto I am working on is a learner and low budget. I bought the paint already so I am going to use it and give it a try. It should work out alright on this one as I plan to go thick, have a ton of time in prep and am not after a show condition truck with this one. Plus the paint shop is 100 miles away (each way) and I am not heading over soon but do plan to shoot the frame soon. I have been using some different products than POR15 for the last year simply becuase I have to order POR15 via the net and the other stuff is here local. Used POR15 stripper but that is about it. What I been using works ok but I want to try more POR15 stuff (rust nuetralizer & ect) on the next frame off. I like the powder coating a frame and under a truck simply because of the types of coating available. Some cool stuff and I do like to get a little freaky on detail under a truck. I kinda plan to give p/c a whirl on a future project too, just to see if I like the results or not.

Can you reccomend an epoxy to use on a chassis? And how many parts hardener (catylist sp?) are you using? Plus how about your primer preference? If you don't want to give up secrets no worries....
 
I have used the rustoleum on 2 frames before and both have held up very well for a few years. The oldest one still looks almost new but lost a bit of the sheen over time. POR 15 is a wast to me. Way too expensive and difficult to apply and I dont think you can really get it all into where it needs to be. I have powdercoated before and would do it again if price was no object but I am not sure it is really needed. It is more of a luxury than a requirement. But a nice luxury.

This is not to be a show quality truck. It is to be a very well restored truck that will last many years.

No Jason, we are not using spray cans! 4-5 coats of both primer and top coat with a HVLP gun.
 
Finished the frame today. Got all the parts divided up and on shelves; all nice and neat!

We began to work on the tub. We knew there were some issues with it but I did not think it was so bad we needed to replace it. Changed out minds. Called up and we got an Aqualu tub on the way.

The firewall on the original tub was not quite shot but I had another firewall/tub that i had dipped a few years ago. Decided to chop the dipped firewall and mate it to the Aqualu 3/4 tub once it shows up.

Going out tomorrow to pick up a trailerload of stuff!
IMG_2650.webp
IMG_2651.webp
IMG_2660.webp
 
Wow, that tub is shot...

As much as I hate aluminum... I would have done the same thing :D
 
TJDIV said:
Dude, your trailer RIG kicks ass.....
That is the Lead Sled of Love. Homosexual Sam uses it to drive around to the dumpster etc... It is an old Crapsman mower we supped up a bit then added 31x10.50s to the back. It is the MOST dangerous thing on 4 wheels!
 
redrustbucket said:
Holy wheelie machine. I bet you can hang some serious ones with that sucker.
It does not so much wheel as flip. The clutch is out so it sorta jerks into gear then the rears lift the fronts up and over you go. Helmet is required at all times.
 
Back
Top Bottom