FJ62 Coolant Levels

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 7, 2016
Threads
21
Messages
102
Location
Burbank, CA
Guys - looking for any advice or input. Replaced the valve cover gasket and there was green coolent sitting on top of the valves. Didn’t have that mayonnaise look that you hear about. No overheating. Coolent level pefect. Doesn’t run hot. Stumped. Any idea what this could be?
 
Last edited:
Definitely coolant and definitely sludge from leaking coolant. I’d say your head is cracked but I get told I’m wrong a lot. Head bolt holes are all blind, right?
 
I don't know off hand, could there be any logical reason coolant is on top of the head, was the truck worked on...? But classic sign of either a head gasket or cracked head/block. Engine oil and coolant in general do not appear to be contaminated?

Assume you have checked all around for anything that is broken on the oil system or cooling system...ie radiator, oil cooler, etc.
 
Head cracks. Hairline cracks. Or a bad head gasket...probably a cracked head though. If you pull the head off and have it magnafluxed, then you can see the cracks. Drove mine like that for a couple years but didn't have 1/2 of the coolant on top as you. No adverse affect to my power. Only question is how much coolant is getting in your oil and at what point will it affect the low end bearings. Shop around for a used head and make sure it has the right part # on it. Ask if it has been magnafluxed or will they take it back for a full refund if it fails your magnaflux check. Get a head gasket kit, I got mine from Partsouq. Take the new head to a head shop and have them replace the valve stem seals that you provide from your kit. Have them check everything over...including cracks, warpage, valves, valve seats, valve guides, and shave the mating surface.
 
Cracked head or blown head gasket. Whatever is causing it, the cylinder head has to come off and examined carefully.
When removing the head, (or if someone does it for you) be sure to pull it carefully from the block. It'll be stuck on there. Try not to mangle the head gasket (too much) when removing it because the old head gasket might reveal telltale signs of a possible leak if the head isn't cracked.
Treat it as a crime scene. Don't mess up the evidence until you've pinpointed the perpetrator.
 
Disassembly of parts in order: I did not remove the exhaust pipe (step 2) but instead went back further and removed the two 10mm nuts from the rubber mounts and took it loose as to be able to flex the exhaust on the pipe away from the head.

2022994
 
Also no need to remove the valves....your head shop will do that. But you will need to remove the rocker assembly. And it is worth disassembling the rocker assembly and cleaning each rocker blowing out old clogged oil and sludge from the oil passage ways with compressed air. Also cleaning the rocker rail passages. Just keep everything in order.
 
Cracked head or blown head gasket. Whatever is causing it, the cylinder head has to come off and examined carefully.
When removing the head, (or if someone does it for you) be sure to pull it carefully from the block. It'll be stuck on there. Try not to mangle the head gasket (too much) when removing it because the old head gasket might reveal telltale signs of a possible leak if the head isn't cracked.
Treat it as a crime scene. Don't mess up the evidence until you've pinpointed the perpetrator.
Many thanks!! Will do
 
This image is inspiration for you. Notice the 2x4" piece of wood. This is resting on top of the pcv valve piping and was used to assist in removal and install of the head.

View attachment 2023001
Thanks for all the information. I’m afraid it may be a cracked head. Interesting thing is that all the fluid levels remain perfect. Also - no loss of power or overheating.
 
I don't know off hand, could there be any logical reason coolant is on top of the head, was the truck worked on...? But classic sign of either a head gasket or cracked head/block. Engine oil and coolant in general do not appear to be contaminated?

Assume you have checked all around for anything that is broken on the oil system or cooling system...ie radiator, oil cooler, etc.
I have had recent work done. Valve cover gasket, side panel gasket, oil pan gasket, AC system checked for leaks and recharged. New radiator fan. Could any of those accidentally get coolant under the valve cover?
 
You need to get a Cooling system pressure tester and pressurize the cooling system (cold) and see if there's any visible leaks in the top of the head. You can rent for free from Vatozone. Make sure you get an adapter for your radiator.

My first guess would also be cracked head, but there are multiple coolant 'Expansion Plugs' under the valve cover. They usually don't leak because of oil bath (so no rust) but anything is possible on a 30+ year old motor.

You can also get a Hydrocarbon in the coolant tester (cheap on Amazon - Combustion leak detector) to see if there is blow-by in the coolant to help diagnose a HG, but I think a HG is unlikely, though possible.

Where did you have work done, K&H ? (I'm in the Valley).
 
Thanks - got the most recent work done at Topline Performance in Huntington Beach. They believe it’s a cracked head. They do good work but really just looking for a second opinion since I don’t have any symptoms like overheating or loss of power. Maybe I’ll try K and H.
 
I have had recent work done. Valve cover gasket, side panel gasket, oil pan gasket, AC system checked for leaks and recharged. New radiator fan. Could any of those accidentally get coolant under the valve cover?

most likely not any of the items listed would have caused the coolant on the head.
if it was me, I would clean it all up, no sign of any coolant. button it all back up and run it for a while, then remove the valve cover again and see what's there.
 
Yeah, I didn't mean to imply the shop where the work was done had anything to do with the current issue - Those items are unrelated.
 
most likely not any of the items listed would have caused the coolant on the head.
if it was me, I would clean it all up, no sign of any coolant. button it all back up and run it for a while, then remove the valve cover again and see what's there.
Thanks - sounds like a plan.
 
I have had recent work done. Valve cover gasket, side panel gasket, oil pan gasket, AC system checked for leaks and recharged. New radiator fan. Could any of those accidentally get coolant under the valve cover?

unlikely that any of those repairs would introduce coolant to the top of the head. At least I can't envision that, if for some reason while the value cover was off there was a spill of coolant then that should have been dealt with. You need to address this because coolant in the oil or vice versa is going to cause you some problems with bearings...or other things. I'm betting the cylinder head is cracked base on internet pics.... Stop driving the truck or running the engine. The shop doing the work should let you know if they spilled coolant and they should have done an oil change. You need a compression check and likely some other testing to check where you are with regard to the cylinder head.
 
Back
Top Bottom