Electrical failure or what? - another setback

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Well, I thought I had good news. Found my receipt from Napa, went by this morning & my alternator was still under warranty. Good new huh? Except that there are none available....so I have a part under warranty, with no replacement available.

Having trouble finding the Bosch AL229X mentioned above also. Out of stock everywhere I've looked so far except ebay, and I'm not real comfortable with that.
 
I'd call and complain about the waranty on the alternator. Napa couldn't find a replacement alternator for my Ambo, but they were willing to ship off my alternator and have it rebuilt. Cruiser alternators may be hard to find, but they do exist and can be rebuilt.

Ford had no stock for mine in North America... for $859, I wasn't too concerned when I'd found a new one locally for $300.

Personally I'm happy with the 120A alternator I've had in my cruiser for 21 years. I've had to replace the bearings a few times, but that's not a big deal.

Hang in there, you've had a long journey getting to where you are, but it'll soon be over and you'll get to start enjoying the legendary reliability of a 40. In 26 years and 100k miles I've never needed a tow, and I've only not driven it all the way home twice. One was entirely my fault, and the other was when a 36 year old block heater broke and spewed antifreeze out the huge hole it left in the block. I could have shoved something in the whole and filling it up with water, but at 11:45 pm, I chose to park it and come back to fix it in the am.
 
bad or loose ground or fusible link?
re-seat all the fuses in the fuse panel?
did oreillys test the battery to be good?
 
Did you check your alternator belt, as @Burbot suggested?

... and charge the battery, test the battery, then start her up and test the battery while she's running... to make sure the alternator is charging?

I've had a loose belt cost me a couple of hours in a remote area.

I've also had auto parts tell me the alternator tested good. When I went back home and tested the battery (as above), it was obvious the alternator wasn't working.
 
Battery was tested and fully charged - I picked it up today & I get 12.7 volts.
Alternator rebuild shop called late this afternoon, so I'll get it back tomorrow. Once I get it back in, I'll test the volts while running to make sure it's charging. The belt seem fine when I took it off, but again I'll verify once I get the alternator back.

dude at O'Reilly's told me it was bad, after trying to buy a new one all over town, I went to the old school alternator/starter rebuild place. That's the guy who told me it was working perfectly - I tend to believe him over the first guy. Especially since it was in his best interest financially for it to need rebuilding.

I'll update over the weekend.
 
If it is any help, I had the same thing happen when the pimple faced , uneducated, person at O'Reillys tell me my alternator is bad and it was not. I watched him hook up my alternator to a universal machine and press some touch screen buttons for the make , and try and spin it using a generic belt. The results certainly showed bad and he seemed to be quick to get away as the machine seemed like it was not being used correctly.
That alternator shop is well equipped to test and I am glad to hear you did not go down the rabbit hole.
 
Alternator is back on. 12.7 volts off, came up to 13.95 running. Dropped to 13.28 with headlights, fog lights, seat heaters, radio, etc all turned on.

Must have been a loose wire, I'm sure the belt was tight when I took it off.

Anyway, as always, thanks for helping me pretend to be a mechanic.
 
Just so you know, I just replaced my alternator had looked high and low for my voltage regulator. Found out the alternator had been replaced with a delco with and internal regulator.
Also, if you can't find and alternator to match you existing engine mount you can place your old alternator mount on the new alternator and it goes ba k together easy as pie. Make sure your connections match up.
 
Well, I thought I had good news. Found my receipt from Napa, went by this morning & my alternator was still under warranty. Good new huh? Except that there are none available....so I have a part under warranty, with no replacement available.

Having trouble finding the Bosch AL229X mentioned above also. Out of stock everywhere I've looked so far except ebay, and I'm not real comfortable with that.
The finding of the replacement alternator is not your problem--it is NAPA's--hold them to their warranty!
 
I agree with everything @Solace in Solitude has suggested above. This has been my experience after my lights nearly went out completely and the engine was sputtering as i was pulling in the drive a couple years ago on my '79/40. Luckily i made it back home to find a loose belt. Glad you have it running again, love your build and your attention to detail. Beautiful 40
 
6502E308-E9DE-49FA-B75B-8C3E9E598139.webp
864D8549-2711-4334-B529-681A28659522.webp


So a follow onto this thread. I have the below Voltage Regulator (Toyota 27700-54040-84) I’m attempting to wire into a harness I’m building for a 1982 FJ43. For the life of me, I can’t determine with certainty what wire is what and I’m asking to prevent frying the unit.

I believe (but looking to confirm) the following:

IG = red wire
N = White wire
F = Green wire
E = Yellow wire
L = Black wire
B = Blue wire

IG N F
— — —
— — —
E L B

And when looking at a 1982 wiring schematic, do both the IG and E go to ground/earth? Earlier years (1980) did not ground the IG via a condenser...so I’m confused.
 
These are NOT oem wire colors:

IG = red wire
N = White wire
F = Green wire
E = Yellow wire
L = Black wire
B = Blue wire

I’m colorblind, but, to me, it appears you are plugging two slightly different colored halves of that green connector together.

The wires, from the connector to the harness appear to be oem.

Is it possible the connector has a “key” to prevent incorrectly plugging the halves together?

Or, are there PIN numbers that can be matched, between the two halves?

Failing those possibilities, have you removed the regulator cover to see if the wire origination point are labeled?
 
So, looking at Roger’s (@Racer65) picture, in post #9, above (is your picture his picture, from post #9?)... it appears to be the same connector and wire colors (and the same picture).

Perhaps Roger can provide guidance.
 
Yes, but the schematic I attached above does have IG going to earth. Am I reading my schematic wrong? It shows two earths: IG and E.
 
Back
Top Bottom