Driving without inner birf c-clip

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 14, 2014
Threads
12
Messages
96
Location
Brno, Czech Republic, Europe
So

after a day or so of front axle re-seal hell, I am in a situation of a complete 80 cruiser (on all wheels) which is missing one (left) birfield inner c-clip -- the bitch, that tries to hold the inner axle in the birf so you can't easily disassemble it.

The question is -- can I drive the car at least to my nearest toyota mechanic -- about 20 miles? Or am I in danger of a serious whatever trouble?

Or I can have it towed, but I'd be very much interested in not having to do that.

Thanks for any replies!
 
Never tried it but, if there is enough spline to allow the shaft to be able to 'walk'out enough to bottom out in the birf bell area, it could jam the birfield preventing it from turning i.e. steering.

That is pure speculation on my part in the absence of any replies thus far.

Regards

Dave
 
Thanks for reply, beginning to be nervous..but before putting the whole axle back together (and this is the reason I decided it should work) I tried to put the half axle (the axle without the birf on its' end) into the axle and the diff; tried to push it further inside the diff and it could not go any further than the axle seal ,,thick part'' on the axle; so from my ,,measurement'' the axle can not be pushed into the diff any more than about 5mm past its' normal position.

Most definitely the shaft cant't walk out of the birf into the diff. ...er.. to my best knowledge and hope. That's why I'm here to be certain:)
 
No that's is a very bad idea and will destroy your birf in that 20 miles, just take the birf and drive shaft out then lock your center diff, you should be able to drive to the dealer without issues.
 
how so? if the axle cant't crawl out of the birf? Sorry for being hard headed but I really can't see why..dunno
 
how so? if the axle cant't crawl out of the birf? Sorry for being hard headed but I really can't see why..dunno

All due respect but you asked for advice and it was given....and then contest the answer?

Regards

Dave
 
I don't 100% know the answer because I've never experienced it BUT without that specific clip the axle shaft will be able to "walk" between the birf and the carrier. What that "potential" distance is I don't think anyone knows because no one has ever done this, that I know of. Having the axleshaft potentially walking INTO the carrier frightens the hell out of me. I'd rather just remove the axle shaft completely and remove the possibility. Or do what Jon Held did and use that pipe block and remove the whole birf.
 
why even risk it? use AAA or find a buddy who has it. Get car towed there for free.
 
Towing those 20 miles will cost me about as much as I paid for the whole seal and bearing set and ordering this c clip will be about a week. So either I take out the birf which means take the whole thing apart again (the wife and kids already dig the fact I've been under the car for two days of our vacation) or leave it like that. I guess I will try some circles around town tomorrow and see what sounds come out of the thing. Really as I can see there is no way the axle will go into the diff. Even when looking at the splines, they are milled half way into the saft so there is no way the carrier spline could walk past the axle spline.
 
If the axle walks like stated above into the carrier bad, if the birf starts smashing into the inside of the knuckle ball bad, call uber, or order, or pull the birf and axle out and roll in two wheel drive. It's your truck do what you want, new cheapo birf and axle couple hundred bucks, new axle housing used 500 bucks new gears and carrier 1000 bucks cause you prob can't set up or used lets say 300 bucks, all for 2 dollar part, your call
 
according to this photo there is really no barrier in the carrier to block the axle walking inside it; so the axle should easily be pushed by hand into the diff by at least an inch or so, not 5mm. And the way it's milled (see here) is the only thing that keeps it in the birf now..

Again I definitely don't want to make anybody angry; I am just curious. Taking everything apart and putting it all together will take me at least 2 - 3 hours knowing all these hours are worth no good at all, because they'll have to take it apart again in the shop yet again :)
 
Last edited:
I could take the easy way and not take off the hub and brake rotor off the outer (howd'yallcallit?) outer hub, but still it's 2 3 hours.. really, I know, maybe you guys can do it faster than me but I know how long it took me just because I've just done it meself:)
 
I could take the easy way and not take off the hub and brake rotor off the outer (howd'yallcallit?) outer hub, but still it's 2 3 hours.. really, I know, maybe you guys can do it faster than me but I know how long it took me just because I've just done it meself:)

What difference does taking of caliper and rotor make? If you take off the drive shaft and drive plates, the axles (and birfs) are just going to lay there like a lizard on a rock. [edit] That's plural, drive plates/flanges BOTH sides.
 
Last edited:
How about take off both drive flanges and front drive shaft and lock center diff and drive.
X2. Easiest and safest way.

However, I cant imagine any of this is better than just ordering the clip and installing it.

Someone should be able to overnight one to you.
FJ80 Birfield Inner Snap Ring - Yotamasters

Edit: Cruiser Outfitters P/N FACL34005

You can always martack it:beer:
Martack
 
Last edited:
How about an easy way pull the axle and lock center diff and go get your part, if they have one in stock. Oh yeah if you don't want an answer don't ask a question
 
Back
Top Bottom