Drawbacks to using drop brackets?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 10, 2004
Threads
365
Messages
5,090
Location
Orlando, FL & Southampton, NY
I'll most likely be picking up a set of 850 heavies to replace the saggy OEM springs and 2" MT spacers :hhmm:

I've been looking at MAF's 2" drop brackets and I'm just curious as to why most people go with bushings instead for caster correction :confused:

I know the bushings would probably be better for off-road use, but how bad can the brackets be when compared?
 
I have the MAF 3" drop brakets on my rig. I'm running the OME heavies with no extra load which gave me about 3.5" of lift. I had a wondering issue that the drop brakets fixed. My pivot point dropped 3" when I added them which restored the control arms up front to the factory angles and added about 3" of drop flex. Once I increased my flex I found a new problem. I was hitting my front sway bar. Instead of spending money I just removed it. I also noticed my front shocks and brake lines were now too short. I added some spacers to my shocks and removed some of the braketry on the brake lines to make them a little longer. That's a short term solution until I can afford some SLEE brake lines and nice shocks. Overall I love the on road stability and added flex of the drop brakets. The only real set back is that they slame into the rocks a LOT more often. I plan to box them fully in with some 1/4" plate so I can just smash them up and not worry about them.
 
I have 850's and ome yellows and recently purchased drop brackets so I can go back to oem bushings and properly correct caster. I don't wheel hard enough to notice the reduced clearance but ill notice the improved ride every time I drive. Waiting till spring to install. Hth.
 
Aren't you running 2" spacers on top of the 2" lift? If so that puts you at 4" over stock. Castor plates work good for this size lift.

No, I mainly got the 2" spacers as a temporary fix when I added my winch years ago.

When I step up to the 850 heavies, I won't be using the spacers.
 
The bottom of my radius arms have seen plenty of rocks. Can't imagine what the drop brackets would be like after a few hard wheeling trips. I think the one and only issue with drop brackets is ground clearance. Most of us don't want to give that up.

Mine are starting to look pretty bad. They are built out of 1/4" wall so they are quite beefy and can take a large amount of punishment.... BUT there is only so much they can take. They really need to be fully boxed in so no matter how much abuse they take they will retain their shape. That will be done this summer when I have some time off. I drive it WAY more on pavement then on the trail so for my situation they are great. They give great road stability and since I don't have a front sway bar anymore I REALLY need them.
 
Do they make caster plates for 2" lifts?

I thought they were for 3" and up :confused:

To my mind, caster isn't something to address at all until you are at or around 4" of lift...kind of like panhards.

850 heavies and 1.5" MT spacers gave me over 4" (by a bit) on my old 80...but I didn't have a winch...just an ARB.

But I see now that you aren't going to replace the spacers...

I would be tempted to not worry about it until you went bigger.
 
Mine are starting to look pretty bad. They are built out of 1/4" wall so they are quite beefy and can take a large amount of punishment.... BUT there is only so much they can take. They really need to be fully boxed in so no matter how much abuse they take they will retain their shape. That will be done this summer when I have some time off. I drive it WAY more on pavement then on the trail so for my situation they are great. They give great road stability and since I don't have a front sway bar anymore I REALLY need them.

Same boat as bhicks ^. But I have the 4" brackets. IMO they are the best off the shelf solution for maintaining ride quality after a lift. But they do hang down and grab rocks like a mofo. That's honestly the only reason I don't like them.
 
To my mind, caster isn't something to address at all until you are at or around 4" of lift...kind of like panhards.

850 heavies and 1.5" MT spacers gave me over 4" (by a bit) on my old 80...but I didn't have a winch...just an ARB.

But I see now that you aren't going to replace the spacers...

I would be tempted to not worry about it until you went bigger.


With my current setup (original saggy OEM coils and 2" MT spacers), I'm at -0.3*

With the 850's and no spacers, I'm thinking maybe a 1" height difference from what you see here :hhmm:


dtracsinstalled2.JPG


If this is the case, what would you expect my caster to be then?
 
The main advantage the drop brackets have over other solutions is that they maintain stock angles on the arms (i.e. smoother ride).

Correcting caster at the axle end leaves the arms at a steeper angle, more vibrations directed through the arms to the frame as opposed to being soaked up by the springs/shocks.

I have 3" drop brackets right now with 850J's in the front. The ride is excellent and they went on super easy.

If you can live with the crappy clearance they are great.
 
I had the J-Springs (heavy) and L-Shocks and yellow OME bushings on my vehicle for about 2 years. This last year I went to Slee's 4 inch lift because I had added so much weight (about 6700 LBS). My J-Springs felt squishy when wheeling. The Slee 4 inch lift is an incredible improvement. I did all of the red trails around Ouray and Silverton in August and never touched the bottom of the vehicle....no scratches on my sliders, skid plate, front or rear bumper. The brackets have never been an issue because I am so much higher off the ground. I am not particularly worried about dragging them on the ground because they are on there so solidly.
 
I too have the drop brackets. On-road manners are wonderful, even with a 4" lift.

But yes, to re-state the obvious, they hang low and are susceptible for getting caught up on rocks. While they have made contact with a few rocks, they haven't actually been damaged. The material from the MAF brackets are pretty beefy, and hold up well, however its been on the back of my mind. Most likely will be swapping them out with axle mounted brackets for peace of mind.
 
Now imagine the performance of the drop brackets with none of the clearance issues!

PS: Newtomelx - I could kiss you lol
 
Back
Top Bottom