Do you need a head gasket?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 28, 2018
Threads
21
Messages
96
Location
Michigan
im in Brazil and all the 40,s are diesel. I’m 500 km from Argentina and my visa for Brazil is up in 7 days. Bummer I blew my head gasket. They don’t have this gasket here. There are looking to find a guy to make a copy. Second opinion is to order one and wait here for it.

My question is ( third opinion) can I use anything else to make this gasket. Anyone have any old tech back yard fixes for this?

By the way I’ve driven from Lima around 17,000 km to get where I’m at now.

Anyone that can help with sending me a gasket would also be helpful.

Thanks

B473B6C2-D44E-40A3-9D9A-2A6B1B840935.webp


032258BA-057E-451E-9F64-7EF274D1D3D3.webp
 
The odds are better than 50/50 that your head and/or block is not even any more at the point where the gasket blew, so without milling to return the surfaces to flat you will only succeed in blowing out the replacement gasket as well.
 
It is the second time it’s blown in the last 9 months. But not in the same spot. I had some trouble going over the mountains in Peru. Over 4000 meters for a long ways. Some garage changed my timing and got me through but I think that could be why the gasket looks so beat up. ( delt with many fouled plugs and adjusted carb many times) this is not original gasket. I bought it in Peru. So no say. A week before this happened the timing was adjusted to 12. It was running like new. Had power made it up long hills. Was great. The gasket healed for a week.

There are machine shops here to check if it’s flat. Would I only need to resurface the head?

As you can see in that picture those water rust spots do have a divit where the gasket was not covering but I thought it was ok because it’s not near the edge.

Also a couple of my head bolts look rough. But when I took them out they were all still tight where they were torqued. I have not been able to find new ones here
 
Resurface the head and deck the block, that way you'll know it's right and the head gasket will last. Admittedly it's a bigger job because you'll have to pull the motor and tear it down, but the alternative is the risk of blowing another head gasket in the middle of nowhere.
 
To clarify, is it an F or 2F gas engine?

You've stated all the 40s are diesel... but your's has plugs and plug wires. For my money I'd pur in a Diesel... 3B Toyota or Mercedes Turbo Diesel before putting a bunch more into that engine.
 
I agree that would be a good option. But I’m not sure what or how long that would involve. I’ll ask that question. For example can i use the same gas tanks?
 
I agree that would be a good option. But I’m not sure what or how long that would involve. I’ll ask that question. For example can i use the same gas tanks?


Yes same gas tanks. For a B series you'll need a diesel input shaft.
 
Last edited:
Yes same gas tanks. For a B series Trans you'll meeed a diease input shaftt[/QUOTE

Spell check strikes again!!!
Or you want your tranny to be sick:).
 
So, you need quick answers and a quick fix.

You have to drive 500km, to Argentina, and be out of Brazil in 7 days.

I’m not near home, or I would send you my spare 2F head gasket.

But, you need to be clear... is your engine an F or a 2F??

I’ve read of people building low compression head gaskets, using annealed copper... but, have zero experience and really wouldn’t want to chance it.

“Bandeirante” F and 2F head gaskets may be available in Brazil... and may fit.

Try googling “homemade head gaskets”.

Hope that helps.
 
That and posting at 3:15 am... not having slept yet. If I didn’t know better I’d think the poster had had a few to many :D
 
To clarify, is it an F or 2F gas engine?

You've stated all the 40s are diesel... but your's has plugs and plug wires. For my money I'd pur in a Diesel... 3B Toyota or Mercedes Turbo Diesel before putting a bunch more into that engine.

So, you need quick answers and a quick fix.

You have to drive 500km, to Argentina, and be out of Brazil in 7 days.

I’m not near home, or I would send you my spare 2F head gasket.

But, you need to be clear... is your engine an F or a 2F??

I’ve read of people building low compression head gaskets, using annealed copper... but, have zero experience and really wouldn’t want to chance it.

“Bandeirante” F and 2F head gaskets may be available in Brazil... and may fit.

Try googling “homemade head gaskets”.

Hope that helps.


The picture of the engine shows the oil fill tube that ended 9/71 so would be a F engine.

At the end of the production of the Bandeirante it was running a Toyota diesel engine. For many years prior to that they had a Mercedes diesel engine. When the Toyota petrol engines ended not sure but could see why finding a head gasket for a petrol F engine could be a issue in Brazil.
 
To clarify, is it an F or 2F gas engine?

You've stated all the 40s are diesel... but your's has plugs and plug wires. For my money I'd pur in a Diesel... 3B Toyota or Mercedes Turbo Diesel before putting a bunch more into that engine.

It is my understanding that @pickelltree is from Peru, stuck in Brazil with a blown head gasket in his (F or 2F) engine, and he can't find a head gasket because all they have in Brazil are diesel engines.
 
After a 30 hours trip / bus ride to the Bolivia border where I walked over the border 3 days in a row going to part store. I found a gasket for my gasoline 1971 F engine. I bought 2 of them.

During the time I was waiting I cleaned the block and head really well. I think this gave me a problem. I installed the 1st gasket and it ran and soundsed great. Then I got smoke. I thought it was just left over burning off. So I let it run. I had drained the coolant and oil before replacing the gasket so when I checked the dip stick my heart sank when it was muddy like oil and water.

So well I was in Bolivia I extended my visa for Brazil. But I have a plain ticket now on dec 24 to see my girlfriend. I leave from Montevideo (1700 km away). Hmm. Can not make plans when you’re driving a 40!

My question. Since my cleaning has seemed to open up years of wear that was filled before with grime. I will get my head decked tomorrow ( I hope). I’m worried about taking the block out because I’m far from parts if I need something. I have a gasket kit from Bolivia. But I’ve never done it before. Will only getting the head decked cause problems when mating with block or should I do both or neither.
 
  • Like
Reactions: flx
Also the oil tube from the pump to the valve cover area had been vibrating against the head and there is a small crack/ hole. I ran it today with the cover off for awhile well I adjusted the valves and it is a significant hole that the oil is coming out from. It seems like there is enough room to cut the pipe well the head is off and join another section on to it.

Will that work or do I need to drop the pan and replace the entire tube?

Time table for those wonder

Yesterday installed and assembled new head gasket
Today morning added oil and coolant
Adjusted valves
Saw hole in oil pipe
Noticed smoke and oil coolant mixture
Cried for a bit
Took head back off
Waiting for Monday to find a pipe fix and deck head
 
It looks like many people resurfaced heads and blocks with sandpaper. Any one done that. Can it be done on the block with out removing it?
 
Got the head planned at a machine shop 100 reales or about 25 bucks at a professional looking place. Lots of machines and engine. Got it back the next day.

I sanded the block well still inside. I’ll post a picture.

Go at everything together and battery’s dead. I’ll have to wait till tomorrow to know for sure if all is well but it went pretty smooth

One problem. Under the air filter bracket I didn’t see and left a washer on one of the studies for the manifold. This made the engine very loud whe I started at first. After a lot of monkeying around I pulled the manifold off and discovered the washer.

The oil pipe I had soldered. I’m hoping that will be the fix for that. You can see that in the photo also.

In the morning I’ll adjusted valves then hopefully start my 1700 km drive to Montevideo to catch a flight on the 24. I hope the 2 border crossings and my 40 are smooth.

F4381974-F2EE-4AA7-90C3-BF973017B738.webp


0BB31D5B-2605-49A5-B854-C2F144021997.webp


7A84161F-EC26-461C-B4C6-4C16D46475C4.webp
 
Back
Top Bottom