Different electrical seat problem

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 12, 2012
Threads
75
Messages
348
Location
Lafayette, La
I was taking out my glovebox today and when I went the push the seat back... Nothing! It was working fine just yesterday! I recently replaced the gear like everyone has had to do and I do have the cap on it.

I unbolted the seat and just one side would move like when the gear was worn. Took it apart and the gear was fine, and turned the shaft and I could see the other gear turning freely. Put it back together and the same problem. After a couple of times it gave up altogether like before I took it off. Rails are unobstructed and I have no idea what's wrong.
 
Does the motor turn? Or is it electrical?
 
When I hit the switch it did work, but was only moving one side then stopped. I'd hit the switch back and forth, but wouldn't move. Took it off to see if it was bound up by something and it wasn't. Put it back on same results. Seat moved like it did before I had changed the gear, then it just stopped.
 
Did you at anytime unbolt the seat from the truck? It happened to me about a year ago, I pinched the wires when I installed the seat back and had the same issue you're having. A forum member told me to go over under the seat wiring making sure nothing is pinched.
It's worth trying, I took a dash apart for no reason :(
Good luck and I hope this works for you!!!
 
When I did my gears in my seats I was concerned about the tracks alignment to each other. all the threads I read said to keep them in the same spot as when you unbolted them, hard to do. What I did was after replacing the gears and before I finished the bottom side, I ran both tracks all the way back and then bolted everything back tight, that way the seat was in the farther-est position and that seemed to keep them spot on as I have had no issues with either seat since. It sounds like one track is a few teeth ahead of the other and it is bound up, similar to when a gear is stripped, one side only wants to move. Just a guess on my par but might be worth considering.
 
I had a similar problem this weekend while removing the front seats for the new carpet install. The seat just stopped moving. So I found on the front of the seat frame, there is a white tube (channel) and on the end closer to transmission hump there was a small white threaded cap that had fallen out. Seems like that cap holds the motor shaft in place. I found the cap, screwed it back in and motor worked again. I can take a photo later this evening if you can't find it.
 
There is an identical gear on the side of the motor. did you replace that side too?
 
Seems most problems have been on MUD, just have to find the right search term.

Similar issue occurred to me yesterday. Driver seat worked fine and removed to clean carpet. Reinstallation and seat will not move. When connecting the wire before bolting down, I did bump the seat switch and moved the seat before bolting and wondering if something is out of alignment. Can’t recall exact sequence, but ran the seat forward or backwards, then forward again to install bolts. Now seems the right side track wants to move and left track does not. Checked and not missing any caps. Tried removing seat to run tracks to verify alignment with same result (right track tries to move, left track seems stuck). Was able to bolt down and manually turn track (left tract that will not move) a few centimeters at a time and hit the switch to move maybe an inch to the rear, and did the same several times to get seat in a comfortable driving position. It seemed doing this would free up whatever had things in a bind, but not enough to make the seat function properly.

Any thoughts on what may have happened and what’s needed to get seat working properly?
 
There is a good online tutorial on the disassembly and reassembly of the seat mechanism on Ryan's @OTRAMM Youtube channel.



However, one of the things he doesn't talk about is cleaning out the old 22+ year old grease that has now hardened and become varnish inside each small gearbox. This was the single most time consuming process. I also had to find new rubber washers to replace the old ones that had dissolved over time. Plumbing parts to the rescue, along with fresh white lithium grease.

There is only 1 motor that runs both seat tracks. The sides are connected through a small, flexible drive shaft that lives inside a plastic tube. If only 1 side is moving, then this can't be an electrical issue.

Aligning left and right tracks is simple. Pick an end stop and set both sides to that before putting the motor back in.
 
Last edited:
@jonheld @OTRAMM Thanks! I’ll give this a try next weekend. For now, have the seat unplugged so it doesn’t get moved. Was strange, worked perfectly with no signs of having a problem before removing the seat. Removed both front seats to clean the carpet and only the driver side developed this problem. Hope it’s an easy fix!
 
@jonheld @OTRAMM Thanks! I’ll give this a try next weekend. For now, have the seat unplugged so it doesn’t get moved. Was strange, worked perfectly with no signs of having a problem before removing the seat. Removed both front seats to clean the carpet and only the driver side developed this problem. Hope it’s an easy fix!
IMO, what happens over time is the old grease becomes hard and binds up the plastic gear in the housing. Since the motor driven worm gear is metal, it just chews the plastic gear up.
 
@OTRAMM @jonheld great video! @OTRAMM Thanks for taking the time to make!

Think there’s any chance the tracks could have gotten out of alignment when I bumped the seat switch? Wondering if removing them and reinstalling with the bracket up against the washer would be worth trying?
If the rails are out of alignment, then 1 gear is not working properly. If the gears and the rest of the mechanism are working correctly, the rails move together as they are joined mechanically by the driveshaft.
 
Back
Top Bottom