Control Arm Drop Bracket

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

flipping arms fixes geometry and castor,

Still wrong... doesn't do a dang thing for the geometry - the 'effective arm' is the same top or bottom

Tank - I'm dropping the baton....

If cardboard cutouts and CAD dwgs from the other thread aren't enough, there is no way to get through....
 
So, in the END (as the proctologists would say), moving the control arm straight forward without moving downwards as well (i.e. rotating) is not the thing to do. Yes / No / Maybe ?
 
LMAO :lol:

:popcorn::beer::beer::beer:

I think its a 3 beer thread

Here's my analogy, bear with me...

Picture your control arms as the handles of wheel barrows :D

I've seen smooth guys with long arms that run with the wheelbarrow handles almost parallell to the ground. Smooth and comfortable, it's how I run a wheel barrow and I'm damn fast, or was in my twenties. I though this was the way to do it, until,

I hired a kid named Jose, about 5'0", who ran with the wheel barrow arms near a 60 degree angle. Rough, uncomfortable, beat the snot out of him, but he ran my ass into the ground all day, everyday, and brought lunch for me as well.

Moral? Control arms parallel to ground are smoother, but it ain't what kind of arms you got, it's how you use them, just ask Jose.
 
look guys, it has nothing to do with the angle of the arms. It has to do with the relationship of the rear bushing and the axle's center. If you were to draw a line between the center of the rear bushing and the center of the axle you would get a value equal to the slope.

Now as long as that slope remains constant the forces applied to the the axle in an upward motion remain constant.

So to effect a change you need to alter that slope.

That is done by either altering the distance vertically (changing the height between the two)

or horizontally (changing distance between the two, the length of the arm)

Just flipping the arm on the top doesn't change either so it changes nothing.The arm's slope is a false indicator of the true relationship that makes a difference.
 
It may be that Ats4X4 means to put the axle under the arm but leave the arm in its stock position. In effect swaping the arm from bottom to top, not "flipping" it without lift.

carry on.........

Has anybody tried this ? I would assume its just easier to buy longer arms that reach the existing mounts under the axle.
rather than fabing brackets on top.............seems to me if you are going to lift the truck and maintain the stock wheelbase the arm length (axle to rear mount) is going to have to get longer (if you don't move the rear mount).
 
Last edited:
I said, flipping it, with 4" plus of lift, of course it changes the geometry, as the new brackets that mount it in its new location fix castor, and camber, and diff pinion angle, and the horizontal arm stops the diff having to go forward to go up.

No matter where the centre of the axle is in relation to the position of the arm, its still on an angle with lift, unless something gets relocated, and still moves forward to go up.
 
No matter where the centre of the axle is in relation to the position of the arm, its still on an angle with lift, unless something gets relocated, and still moves forward to go up.
Isn't this more to do with energy transfer characteristics of the two positions and how that affects the suspension doing the job it was designed to? The arc the axle travels will be the same both ways won't it? But the horizontal (flipped) arm will put almost all vertical energy into the spring whereas with the arm angled of a lot of the vertical energy ends up in the arm?
 
The arc the axle travels will be the same both ways won't it?

Only if it travels the same either side of horizontal, if you space the bumpstop and lift the truck you have moved the travel, so the axle has to go forward to go up still.

If the hour hand has the diff by the No 7 at 7 oclock, and it needs to go to 9 oclock, it has to go forward that fixed amount regardless, where as if its at 9 oclock, and needs to go to 8 or 10, it doesnt move forward or back as far to get there, even if the diff is is 6" below, or above the hour hand, because the hand moves the same fixed amount between No's regardless.
 
Here's my analogy, bear with me...

Picture your control arms as the handles of wheel barrows :D

I've seen smooth guys with long arms that run with the wheelbarrow handles almost parallell to the ground. Smooth and comfortable, it's how I run a wheel barrow and I'm damn fast, or was in my twenties. I though this was the way to do it, until,

I hired a kid named Jose, about 5'0", who ran with the wheel barrow arms near a 60 degree angle. Rough, uncomfortable, beat the snot out of him, but he ran my ass into the ground all day, everyday, and brought lunch for me as well.

Moral? Control arms parallel to ground are smoother, but it ain't what kind of arms you got, it's how you use them, just ask Jose.

now, bend your wheelbarrow handles into an S shape. As long as they end up at the same place relative to the wheel, you get the same effect. Run the handle horizontal from the wheel then up 2 ft, or run it up two feet then back, Jose is gonna run the same either way.

Now, if you space the wheel down further, so your handles come up 3ft, then back, Jose's gonna raise his arms to the same height, and he's gonna run faster....

See Jose, See Jose Run, Run Jose, Run.
 
Since people still seem to be having a hard time visualizing this concept I took the time to draw out the parts in autocad. I took the measurements off of my 4" lifted truck so they would be accurate to real world situation.

These first three pics so the axle movement with three different arm configurations. The first is the arm under the axle, second is the arm straight to the axle and the third is the arm horizontal to the axle.
under.webp
straight.webp
horizontal.webp
 
what causes binding on compression is the fact that if the axles center is lower than that of the rear bushing the axle must also move forward as it compresses. This forward moving motion actually fights forward progress.

On a side note, with a 4" lift the height difference between the axle and the rear bushing is 2". Not a big enough difference in my opinion to be concerned about.
 
Remember when we used to just wheel and poke fun around the camp fire...
The internet is ruining the world..

I personnally love my drop brackets.. Why?
Because my wife drives it every day and can't tell the differance between stock and 4" lift on 35's
Besides that the brackes hange down about as far as my leaf springs on my 40 and it will school the wagons all day anyway

I think the problem hear is a result of to many people that know alittle about alot that are thinking they know alot about everything.

This post was started asking about drop brackets. I think they are the best for a daily driver and the hard core. All this talk about geometry reminds me why i went with bracket. I wanted a solution that keeps it consistent with stock geometry the way Toyota designed it. Any knuckle head with a welder and a ruler can do it differently. That doesn't make it wrong but it doesn't make it better. My bet is always on the Toyota Engineers (thats why i have 4 cruisers).

Take a look at any competition buggy and even they all run conrol arms level. So tube your 80 or drive it daily but why argue about it.

Stir'in the pot
 
Back
Top Bottom