Check engine light code 26

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I believe that rc51kid was suggesting that you clean the O2 sensor connectors due to yeRs of crud build up. I have read of this remedy before.
You removed the "AFM"? Are you referring to the VAF meter that is connected directly to the air filter canister?
 
I believe that rc51kid was suggesting that you clean the O2 sensor connectors due to yeRs of crud build up. I have read of this remedy before.
You removed the "AFM"? Are you referring to the VAF meter that is connected directly to the air filter canister?

Yes sir. The vaf. That makes sense regarding the O2 sensor.
 
Last edited:
You didn't happen to remove the two small screws that retain the male electrical connector to the VAF did you?
 
Your 1994 has two O2 sensors, one just before each cat. The wiring for the inboard sensor is usually routed up and over the transmission and is subject to abrasion type wear along its length. You may want to check this also.
 
The truck started running better and the code went off after driving it a little while. It seems like after the engine warms up the problem goes away.

I dropped the 80 off at my mechanic. Just from talking to him he thinks it's the coolant temp sensor. The engine things it's colder then it is at start up and dumps more fuel then it should at start up. He's going to look at it tomorrow to make sure.
 
Well I have the same issue with the exception of most of the time it idles fine. My O2 sensors are less than 15k old and I also moved mine to the Old Pair plumbing location when I replaced mine. Honestly Im kind of interested to see what your mechanic says the problem is. I haven't tried to fix my code 26 out of shear laziness due to the fact I just did the HG and full maintenance less than 2k ago and I know the engine is in good health. That and I'm planning to do a 4bd2t diesel swap whenever I get my butt out into the garage and finish building it.
 
Well I have the same issue with the exception of most of the time it idles fine. My O2 sensors are less than 15k old and I also moved mine to the Old Pair plumbing location when I replaced mine. Honestly Im kind of interested to see what your mechanic says the problem is. I haven't tried to fix my code 26 out of shear laziness due to the fact I just did the HG and full maintenance less than 2k ago and I know the engine is in good health. That and I'm planning to do a 4bd2t diesel swap whenever I get my butt out into the garage and finish building it.

I just left there. They're getting ready to pull it in. The guy looking at it used to work for Toyota so hopefully he can figure it out fairly easily. I'll keep this thread up to date as I know more.

Does yours idle better after its warned up?
 
I just left there. They're getting ready to pull it in. The guy looking at it used to work for Toyota so hopefully he can figure it out fairly easily. I'll keep this thread up to date as I know more.

Does yours idle better after its warned up?

So what happened with your mechanic? I'm having the same problem and can not track it down. You said you'd keep this up to date, anything? THANKS!
 
So what happened with your mechanic? I'm having the same problem and can not track it down. You said you'd keep this up to date, anything? THANKS!


Not yet. I just left there a few hours ago and they're probably close by now. I am sure I'll hear from them tomorrow. I'll post an update once I know more. What kind of issues are you having? What have you tried?
 
Sorry for the impatience. Ive had this Cruiser for a few months. So far Ive replaced the Air Mass Sensor, Idle Control Valve, everything vacuum related including all 3 VSVs, new O2 sensors and I've even checked valves. I'm at a loss and cant keep throwing money at this thing. I'm a very experienced mechanic, just short on metric knowledge. All the other threads are losses for rel info, was hoping your mechenic would come back with something solid. The code 26, poor idle and loss of power is driving me insane! lol
 
Sorry for the impatience. Ive had this Cruiser for a few months. So far Ive replaced the Air Mass Sensor, Idle Control Valve, everything vacuum related including all 3 VSVs, new O2 sensors and I've even checked valves. I'm at a loss and cant keep throwing money at this thing. I'm a very experienced mechanic, just short on metric knowledge. All the other threads are losses for rel info, was hoping your mechenic would come back with something solid. The code 26, poor idle and loss of power is driving me insane! lol

I understand. I've only had mine for about a month month and a half. Trying to get it ready for a wheeling trip. I'm surprised being an experienced mechanic you weren't able to trouble shoot the issue more and figure out what the problem is instead for throwing different parts into it. I really have the feeling it will be the coolant sensor but we will see.
 
It completely slipped my mind. Im headed to the garage to pull my ECT sensor and test its resistance now. Ill keep you posted, please keep me up to date. THANKS!

Let me know if that's it. Both the guys at the shop thought it could be the coolant sensor since the 80 ran better after it warm up. They did not think it would be an 02 sensor, egr valve, injector, spark plugs, wire or the distributor since it ran better after it warm up. If it was any of those it shouldn't run better after the engine warm up.
 
Last edited:
Update. The mechanic has not been able to look at the 80 yet. He said he would by tomorrow if not tonight. I spoke with the owner of the shop and he did not think it was the coolant temp sensor. He said if it was it wouldn't run better once it warm up that it would continue to add too much fuel.
 
I did a resistance test on my Engine Coolant Temp sensor and it tested good. So my nest question to "sbrodact" or anyone else listening would be... What would the effect be with a bad System Temp Sensor? Alas, i continue on with the great search lol.
 
Any chance you have a small tear in the air intake tube? It could change size/ position as the engine warms up. Used to be a lot of threads about them failing.

Anything is possibly at this point. Would a small hole in the intake tube really cause it to run rich?
 
Back
Top Bottom