cheapest SOA

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 6, 2003
Threads
43
Messages
133
I'm trying to figure out a way to do a SOA for less than a SUA lift kit.

So far I have the aqualu steering arm at $250
brake lines from SOR $150
Spring perches from SOR $150
U-bolts, SOR $66
Center pins $20

I really want Decker's torsion bar at $250, but I think I could fab my own. My only fear would be that it would be made with mig welds, will those be strong enough? I would think so but what do you think?

Anway, with all of that I'm at $786, which is reasonable. However, now I have to take in account new/custom drive shafts, and a proffesional cut and turn. I don't have the skills, knowledge and most of all the resources to do the cut and turn myself. So I'd rather take my axles to a shop and have them cut turn and mount the perches for me. What would you questimate a shop would charge for all that?

I'm figuring at least $200 for the custom drive shafts eh?

So I'm trying to financially convince myself to go SOA instead of the skyjacker kit. I've heard a lot of people talk about doing SOA for dirt cheap, but I think they have shops and do most of the work themselves. There's a certain amount of work I can do, but I don't feel confident in myself to do the cut and turn. Or weld the spring perches on the axle.

How much did everyone end up spending on their SOA's and how much/what work did you do, and what work did you have done?

Thanks,
Mike

Anybody in the VA/MD area? It seems everyone's on the west coast... Anyone know of some good shops in the VA/MD area? I'm gonna be moving to the eastern shore in a month and that's where I'll probably be doing my lift.
 
woah, dude....LOTS of opinions here, so watch out...

1> double arms are SO 2002....http://www.4x4Labs.com for a suhweet solution, http://www.marlincrawler.com for a "more normal" solution, and around your $250 price
2> brake lines? hoses? NAPA, $50 or so
3> perches = Mopar, 2 boxes are like $25 (4 perches)
4> u-bolts = local shop, $8 ea
5> not sure why ya need center pins...
6> IMO, Deckers bar does not address ALL the concerns with SOA...it relies on the springs for the bottom of the V support, and for that reason, I really do NOT like the design. JK Customs has a nice one, or make your own.

retubed shafts are $200-300....new custom ones are $400-1000 (LOTS of variables) If you do a shackle reversal, a front long spline will not be cheap.

I did mine 100% myself, MIG welder...

EDIT: if you are doing an SOA with the intent of being as cheap or cheaper than a SUA lift kit, please don't do it....if you are doing the SOA because you are smarter than the rest of us and don't want to spend money on a 4" lift kit only to regret it and then turn around and sell it for 1/2 price and sink that money and a pile more into a properly done SOA, then have at 'er...just don't skrimp

(I'm serious on the "smarter than the rest of us" comment too...I foolishly did a 4" lift and more, only to discover 2 years later that it was an expensive bandaid....)
 
Last edited:
me also did the after market lift then sold the springs and started in on the spring over .
i almost followed woody's list to the T . . i did replace my center pins u have to flip the pin over for spring -over don't ya .i did . the stock pin usually is rusted to crap or twists off . i just bought allen cap screws from home depot . worked great . also used mopar perches . i did the cut and turn myself also . i had a few longer drive shafts around .so saved some money on the shafts just had to get them shortened . not retubed . and new ubolts .from any spring shop are cheap .


SPRING -OVER WAS THE BEST LIFT I'VE EVER USED .
 
Me too, me too. Ditto what they said. I bought a skyjacker 4" spring kit, then turned around and sold it 6 months later. Just about rattled by teeth out! Invested and did the SOA with all the same components they list above. But, I had Warden's turn my axle for $300. Turning the axle is not that difficult. If I did it again, I would do it myself. IMHO, the axle should be turned only after you have all the other components installed, so the knuckles can be turned the correct amount degrees to be parallel with the TC output. Warden's turned it 12 degrees, which turned out OK for me. The dodge perches are dirt cheap and fit the LC axle perfect. For center pins, I used grade 8 bolts. Cheap again. Also, don't forget you have to get new shocks when all is said and done.
 
I think that you have herd it all, but what's one more opinion, I agree with all the above posts. Make sure you don't try to go too cheep, dont spend more than you need, but make sure that you budget enough for some extras that always come up. And Make sure it is SAFE and reliable. I think Mig welding is fine. You will hear some that talk all day about tig, and it can be stronger when done correctly, but not much. IMO tig is usualy a waste of time.

Good luck
jetboy
 
I will "Me Four" the first doing the SUA lift only to pull it off to do a SOA. With a SUA lift the springs are forced to have so much arch that they make things work not quite right but it is just OK. My soa cost about $300. i already had the u-bolts and the springs. I reused the rear hangers in the front (shackle revesal), reused the shackles, so the only thing I had to buy was the spring perches. The major expence was the front drive shaft (retube / long slip).

But like everyone has said above money shouldnt be the deciding factor. With a well done SOA you will be much happier than puting up with a typical 4" SUA lift untill the point that you decide that you finaly want to spring over your truck.
 
I am waiting on a quote from CruiserOutfitters to do my spring perches and cut and turn.

I'll let you know when and if I hear back from them.

EDIT** My bad CruiserOutfitters not customcruisers

www.cruiseroutfitters.com they claim to do more cut and turns than anyone.
 
Not to hijack the thread, but how does a soa handle in comparison to a sua with lift? I have heard that with a hardtop, it can be kind of top heavy? Also, how much lift does a soa give? Any problems with a sr or power steering?(sag)
 
SOA = minimum 5" lift over stock

Yes, they do handle differently, there is more body roll. FJ40's were never known for their accident handling maneuvers anyways tho. You get very used to the handling on the street, and the added flex/clearance offroad is nice.

SOA is very compatible with GM Sag steering conversions, and workable with Scout Sag conversions too. It's common to do a shackle reversal, custom and low, with the SOA, but SR's generally require a longer spline front driveshaft.

My frame rails are 23" or so from the bottom edge under the drivers seat to the ground...with 39.5 IROK's....I spent a GREAT deal of effort lowering mine as much as possible....
 
I'm ALWAYS in the minority with this topic comes up, but oh well. First off, a properly done SOA is superior to ANY aftermarket SUA lift kit period. Ride quality will generally be better, flex will generally be better and you get plenty of lift.

However (this is my voice of dissention) Those things can be accomplished with the RIGHT combination of SUA bits.

My opinion. Must have's for a proper SOA: axle cut and turn, shackle reversal, hysteer, longtravel front driveshaft, flipped rear springs or new spring hangers for slightly longer wheelbase, this will require a retube on the rear d-shaft as well. Then you gotta factor in new shocks and whether or not your existing shock mounts are gonna work, probably not if you change wheelbase at all.

This stuff adds up cost quickly even if you do it all yourself. So, if you decide that you DON'T want to tackle all of that and decide to stay SUA.........here's what worked for me.

Get some custom Alcan springs made. Alcan makes an awesome spring that is custom tailored to YOUR truck. They'll give you any amount of lift you want, make them as soft as you want, move the centerpin locations, make them for shackle reversals, whatver. Charles at Alcan is awesome at what he does. The Alcans might cost you a bit more than some other springs but your paying for springs built specifically for your truck and your wants. Worth it in my opinion.

I already had a shackle reversal but you can do these springs without and be fine. I know you can do that with a SOA too but personally I don't like SOA without the SR. You'll already have shackles, your driveshafts will already be the right length (most likely)unless you change center pin location or spring length, so you'll just need shocks, brakelines and u-bolts in addition to the springs.

Just another opinion and another option. Do what's best for you.

I've seen some crazy flex out of well built SOA's, but I never complained about the flex I got from my Alcans. :)
 
AlaskanWheeler said:
ProffitsCruisers also has a kit that he sells for about 450 without core. Just another thought.
anyone tried the proffitt SOA kit?
 
I didnt buy his axle, but I have his perches and the sleeves. They are good. if you have the stock shackle hangers already (mine were gone sicne I had the advanced handling kit) use them since you have to take them off your cruiser anyway.

I got my axle from Cruiser Outfitters. Cut and turned, but I had to put on my own perches and stuff. I saved money, but at the same time spent more time getting everything done. This being my first SOA, I spent alot of time measuring 50 times, welding once...

Either way, whether you get your axle form Cruiser outfitters or proffits- you still have to weld on the rear perches as well as the hangers - yourself..

If I did this again, I would cut and turn the axle myself. Its pretty simple.

-Dustin
 
I shouldn't ask questions I don't want to hear the answers to! Well I guess I'll start collecting soda cans and save up $1,500 and go SOA. Untill then I'll just have to keep the back empty so the tires don't rub.

Thanks guys.

Mike
 
BTW, IMHO, Shackle reversal is not necessary for a SOA.

The only reason it is nice is to reduce the chances of smacking the spring on a rock and bending it.
 
woody said:
woah, dude....
(I'm serious on the "smarter than the rest of us" comment too...I foolishly did a 4" lift and more, only to discover 2 years later that it was an expensive bandaid....)

DITTO

I would not do a SUA lift of any kind on any Cruiser for any reason, ever again! Am I clear on that, hehehe. Never because of $$$, although it may take a bit longer to shell out for all the right stuff, as Woody stated it is much cheaper to go straight to SOA. The ride is better, the suspension cycles better, no comparison!

Adam is correct you can get a good SUA setup that may meet your long term needs, but not for less than a good SOA. Don't waste your time on any springs other than Alcans or distant second Skyjackers. The rest are all too stiff or sag quickly.
 
LOL. Yep $16.

Then i had $30 in stainless brake lines front and rear.
And eventually went with a welded double arm on the steering for $50. (did
power steering at the same time)

$96 total. driven it daily at one point, and always available when i need it.

I then also did a traction bar for $25

NO CVs, NO cut and turn, NO shackle reversal.

Build your own center pins, and $150 for perches (damn i am in the wrong business).

Driveshafts, cheaper to shorten then to lengthen. Two driveshafts shorten here is $80 or so. You get into CV and lengten and swapping shaft parts, then triple that $$$$.

End $$$$ will correspond with what skills you have to do what needs to be done. Everything
else comes out in the form of $$$$.

ALCANS will never be used on any vehicle i ever own. Or any of my buddies.
"sag quickly" applies here. Go flat spring warrentied with another set of Go flat springs
(this set the improved version, supposed to be, LMAO) 6" springs maybe 2".

The cheap morso spring perches, and i believe the mopar ones are the same,
are JUNK, if used need to be reinforced. But better off getting your own made,
or making your own.
 
Back
Top Bottom