cat removal

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 3, 2006
Threads
259
Messages
1,935
Location
Fort Apache: Victoria
I searched and didn't find the exact info I was looking for.

Am I going to have any problems if I replace the cat with a length of straight pipe in my '94?

I don't want to run leaded gas, or anything like that. My cat is probably quite clogged (runs VERY hot), and since there's no smog check or annual inspection here I could run without. I anticipate a slight performance and mileage gain.

Will this be a problem for the O2 sensors or the diagnostic system?
 
I'm pretty sure it will be a problem with the O2 sensor. Can you just replace it with a high flow aftermarket unit?
 
The O2 sensors on the 93 & 94 don't care what happens with the cats since they are pre-cat. So no issues there.

If you're just removing it to remedy the warm floor it's not a bad idea to replace them with new high flow units or even one high flow unit. Do you folks up north have emissions tesing in BC? If so consider the retrofit to err on the legal side.
 
The O2 sensors on the 93 & 94 don't care what happens with the cats since they are pre-cat. So no issues there.

If you're just removing it to remedy the warm floor it's not a bad idea to replace them with new high flow units or even one high flow unit. Do you folks up north have emissions tesing in BC? If so consider the retrofit to err on the legal side.

There are no emissions tests where I live; only in Vancouver. The only issue I would have is if I sell my Cruiser to a Vancouver resident; he/I would have to retrofit the cats. As I plan on being buried in my Land Cruiser, however, this isn't really an issue.

Replacing cats is a pretty pricey meatball, so if I don't need them (and there's a possibility of improved mileage/power without them), I'd like to ditch them.

Would there be any issues caused by the change in back-pressure?

I thought the o2s were pre-cat on my truck, but I just wanted to confirm without actually getting underneath it. <--lazy. :D
 
Replacement is only spendy if you use Toyota or aftermarket replacement parts. If you install something from Summit or the like you can be under $100USD.

If you'll be burried in it like the rest of us I wouldn't bother either.

No issues with back pressure.

Lazy - I hear ya.
 
search on catalytic converter and my name. I recently did this on my 96. No errors or anything and the cat I used is small enough to run side by side a la 94.
 
Replacing cats is a pretty pricey meatball, so if I don't need them (and there's a possibility of improved mileage/power without them), I'd like to ditch them.

ditching cats does not improve mileage/power - not on any modern engine anyway.
 
Unbelievable for the land of fruits, nuts and flakes!
:beer:

Eh, you got that wrong. California is down and to the west, not up in Canada. But, if you want to share the title, I'm sure we can work something out:cheers:
 
Unbelievable for the land of fruits, nuts and flakes!
:beer:

The Lower Mainland (Vancouver and suburbs) has an annual smog check called "AirCare". It's pretty strict.

Everywhere else in BC is exempt (for now) because of the relatively low concentration of population.

It's good.
 
ditching cats does not improve mileage/power - not on any modern engine anyway.

The 3FE, IME, likes the free'r breathing of gutted cats. The 1FZ-FE is old enough tech wise to benefit from a little better flow, and if cheap is what you want, cat removal will do it. The hot floor was the reason I gutted mine, 300x cheaper than replacing them. Slider fitment is pushing me to remove them.
 
And while we are speeking of removing cats, how about ridding my entire rig of its polution control, EGR, cats, everything, the cats are in the way of my sliders and the PAIR valve is in th way of my OBA.

Anybody have any success doing this or do we need a new ECU to keep my things running................Senator Swartzenbicep has teemed up with our Premier and by the end of my 80s life I will be looking for electric power anyhow.
 
So getting rid of the cats will also rid me of the hot floor? Mine is a 94 that will never leave Mexico.
 
You can do it on a 96-97 LC or LX, my uncle rebuilt a LC a year or so ago, and the cats were clogged up. Instead of replacing them since there is no need here in KS, he cut them out, the O2 is prior cat, and replaced them with a (now don't laugh) but with a new euro ricer exhaust pipe piece.

Jeremy :cheers:
 
95+ also has an O2 sensor after the cats.

Wingman, all sliders made for the 80 are designed around the factory cats. There aren't many options for 91/92 and ALL options are pretty expensive. I'm thinking that some trail gear sliders with some added beef would be great and cheap, but without having to spend so much time making a bracket that works around the cats, why not eliminate the cats and just have a straight shot to the frame.

MARLIN, this can be done easily on the 3FE motors, but hasn't been done (atleast often) to the 1FZ-FE. I'm positive it can be done, Aussie rigs don't have much of the smog stuff the US models do, maybe the computer can learn, maybe an ECU swap from an Aussie (or other smog exempt models) rig would be best
 
My FJ40 was a Canadian version without the emisions stuff, do you now if there was a gas version of the 1fzfe 80 for Canadian import ( I have only heard of the rare deisel version) prolly same as the Ausie, South American)

Come on history buffs chime in

Sorry Iron yuppie for thieven your thread, but I will take a shot and assume you would be interested in gutting your engine bay.
 
Back
Top Bottom