breather extensions

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 7, 2007
Threads
83
Messages
500
Location
Raccoon City
Website
www.coopxgear.com
OK, Yes i haven't gotten around to it yet. shame on me, so how long will it take for one person to do?? i'm leaving for the armpit of Cali at O-dark thirty for turkey day. i had planned to head up to the family ranch for some light wheeling, but i talked to one of the cowboys up there and the roads are gone and some pretty big water areas. He's gonna have to ride a horse down to a main road to get out for tomorrow. So i'm going to have some time on friday only to do the breather extensions. What say you mud?
 
about 30 minutes if you have all the parts
 
Thanks Romer, thats good news, now i can go play.
 
1 hour for me with all the parts
 
There are several ways to do this I think I followed Beowulfs, maybe I modified it a bit.

Bought 25 ft of fuel line and hose clamps.and 3 T's

took off the rear diff breather hose and attached new line. Put clamp on the end, routed forward up past the front one up to the brake booster. Cut to length and put a T at end with clamp..

Took the hose off the front and put new hose and clamp on, then took other end to T with clamp

Took rear diff breather off, popped the cap like the write-up in the FAQ and then replaced it after removing the piece discussed in the faq..

Added a small section of hose about 4" with a clamp to the T, then at the other end of the 4" hose added the modified diff breather with a clamp.;

Make sure everything is string tied and routed out of harms way

This does the front and rear diffs.

The tcase and tranny are located on the dip stick. You can do these later as they are much higher that the diff breathers. Easy to do, disconnect hoses from bottom of dip stick, add a T with clamps between them, add another long hose with a clamp up to the 4" piece discussed earlier in the diffs, cut the 4" piece and add another T.

I have everything running through one breather. I think thats the process discussed in the FAQ
 
seemed like a halthy discussion, no one got yelled at. I hadn't thought about cross contamination either. My goal was to raise the breather to prevent water from getting in via the breather.

With the way I did it the Tranny and Tcase are higher and I thought that water would get in the breather on these before anything else.

Kevin's method is better, but I think if you seperated out the Transmission you would be OK as everything else takes gear oil. That doesn't make what I said right either. Just what is OK for me. The pure way is Kevins method.

I can easily switch mine over to seperate breathers because they are all accesable from one spot in the engine bay. Would be easy to add.
 
Confused on one thing. Do you just discard the existing hose that runs from the axle to the breather valve and run all new hose with the slack up to the front and then up into the engine bay? Or do you pull the breather caps and connect the hose their and continue running up to the engine bay?
I still need to get my P Clamps and Brass Tees.
 
Confused on one thing. Do you just discard the existing hose that runs from the axle to the breather valve and run all new hose with the slack up to the front and then up into the engine bay? Or do you pull the breather caps and connect the hose their and continue running up to the engine bay?
I still need to get my P Clamps and Brass Tees.

Yeah, run all new hose because now you are extended them. You can run the same caps, you can use fuel filters or you can use a manifold which gets its air from a central point like.
 
OK so just leave the old breather cap assembly and bypass it or spend the time taking it out?


After making sure they are still breathing, yes. They have a tendancy to get clogged with road grime. I just replaced them with cheap fuel filters.


:cheers:
 
Mark - sounds like you and I need a breather extension get together! I need to do this too!
 
Back
Top Bottom