body work!! YA!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

What kind of welder are you using? Are you grinding a lot of metal off to clean it up, You may be making the material too thin, if you have a mig welder turn it down, Larry
 
By the looks of it I would say that even though the machine is turned down it is rnning pretty hot. Do you have access to another machine to test things out? Your welds seem to have no problem holding on though. Hope all works out for you.
 
than I must of hit a soft spot in the metal and it just kept burnning through. and the rocker panels are just a big mess. O and I got a bit mad and tested the welds with hammer

LOL - Don't let my wife see that she will never help me do anything in the garage again!!! (I have been known to lose it too when things in the engine compartment go bad!)
Hang in there.:beer:
 
what does the ground have to do with the weld? should I be using a thinner wire in my welder?

Pretty sure he's referring to the ground clamp - make sure the connection securing the cable to the clamp is clean - mine has a screw that holds it on, followed by a crimp. Also, make sure the clamp in on clean metal - free of any paint or rust for a good contact. As for the wire - the thinner the better for sheet metal. Not sure if you can set up your MIG for gas but that would help with cleaner welds. I am fairly new to welding as well - but these tips have helped me. Good luck.
 
no not at all it was like $97+shipping. I would buy a better welder but I'm 20 and have other things to pay for and alot my cruiser parts to buy
 
The tacks looked good... you should just keep tacking and work your way around a few times. It warps allot less than continuous weld and it will be strong.

Thinner wire will help and I've found turning up the wire speed will help keep it from burning through.


Kevin
 
I have found that it is very dificult to weld body panels. My original repairs could have been those pictures above.

I had an old timer tell me to get a metal 55gal drum and practice on it. He had never used a wire feed so he was no real help. I tried his method with a stick wleder and just blew holes in everything. I bought me a $5 55 gallon drum and cut patches out of it and then welded them back in place.

The experience was very frustrating but all I had invested was a 5 dollar 55drum, a little welding wire and time.

Once I felt I was getting good I started on my body panels.
 
I agree , if you can add the gas to your mig it's worth every penny of the investment. I started on my rig trying to use .035 flux core wire and had the exact same experience. I then tried using straight CO2 for gas and while that did help I was still getting too much penatration and dirty welds. This list gave me many tips including switching to .023 wire and using a CO2-Argon mix. After much trial and error I can now weld on the 16ga without too much trouble. I have much more to learn. Practise is the ONLY way to learn to weld properly. If you can try to take an evening welding class at a local school or if you know a welder ask to watch him. Good luck! :beer:
 
thanks guy for all the help. I'm not going to replace the whole tub. I'm going to replace the rocker panles and the rear sil and the bottom part of the rear quarter panel. should I replace the the rear sil frist or the corner clip. heres the pic of what I plain to use.
d9_0.webp
 
one more thing, what do most of you use to cut sheet metal? die grinder, or angle grinder? or other?

Die grinder would probably be best, but I've managed with cutoff wheel on an angle grinder - coupled with a sawzall. The cutoff wheel picks up where the sawzall leaves off and visa-versa. However, I find it hard to see the cut off line with the grinder due to the sparks - and the sawzall can rip through a lot of material really quickly and sometimes seeks it own line due to flex in the blade, etc. Take your time with either one when cutting and it should work fine.
 
has anyone used the quarter panel patches? I was looking at those and they are 95$ and the whole quarter panel is only 135$, so I would think it would be better to buy the whole quarter panel than just the patch. let me know what you guys think, I really like to hear what you guys have to say and I've gotten alot of good info from the one that have posted on this thread. thanks!
 
Back
Top Bottom