Birfield eliminator Kit

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 6, 2012
Threads
342
Messages
11,021
Is their a birfield eliminator kit available for fj80s? Just got told from the guy I sold my old big 80 series to that a shop he took it to for repairs sold him a set because the birfields were clicking. I had no idea they ever made a kit for the 80. I know back in 1999 they sold them for fj40s and I think they still sell them for pickups.
 
April 1 is coming up...

More seriously, since I'm in intimate communication with my birfs at this very moment -- at least until I took the gloves off to type -- sounds like something expensive if it even existed. I've heard of no such thing.
 
I think it's called a dana 60 swap?
And then if you're a real baller, you get u-joint eliminators (RCVs).

Long story short, the large birfields in the 80 series are a gem of the front axle, especially in chromoly form. I don't like u-joints and I have pricey stupid ones right now
 
The dude is new to the land cruiser world. He heard how good the fj80 is of a rig and how they are used all over the world so he started looking for one and bought mine a while ago. I just gave him a shout to see how the rig was holding up and he said he had that done. He said the shop gave him a good deal. I think high end 4340 ujoints are kinda close to the strength of a chromoly birf.
 
I could use a good birf trivia thread right now and this one seems like its got enough meat on the bone to be with chewing this one over, if I may indulge for some RTH.

The FSM shows 2 C-clips on the end of the half-axle that fits into the female (bell) end of the birf.

No one ever talks about that second C-clip or am I missing something?

I get the impression that the C-clip should be set on the end groove of the axle, then when you drop it into place, the birf slides home, leaving the C-clip at the end of the splines on the inside of the axle end and with maybe 1/4" to 3/8" at the extreme end that is nestled up into the front of the bell opening. That allows things to slip in and out when the knuckle turns The C-clip is a springy thing for this reason to allow for the movement in overall assembled birf+shaft length needed to turn.

So there's just one C-clip into the birf, right?

Thing is, the one being fell out without any effort while the PS is being more stubborn (though I hope it yields as soon as I finish this,,, it's dinner time.) Never had them apart myself, so it's a little mysterious other than this is an unhappy birf. Being a Land Cruiser, it may be a little broke, but it's not given up yet.
 
Yes, there's only one. I asked about it last year. I'd post a link to the discussion, but I'm on mobile and it's a PITA.
 
Birf busted. All is good with the world, at least on this side, except the seal looked kinda rough on the brass. That was probably something I did when I had to redo someone else's work in there. Got tired of paying people and still being worried about safety. At least my boo-boo lasted 35,000 miles and was still working when discovered, while his lasted 4,000 and earplugs couldn't block the squalling. Back to cheaper and (hopefully) safer DIY.

Good to confirm there's only one birf C-clip, thank you very much, although I think I'm probably not really getting how it does work. Toyota has those every so often and I thought I knew the 80's FSM quirks by now, so thanks for helping keep me humble while educating me..

Suffice to say that it's well designed when something so beautiful is so strong. It's all that lust for bigger than 33" tires that contributes to the birf's naughty reputation. I'm just impressed how well they hold up to stupid people. Note I am NOT referring to those who run larger tires but somewhat informed amateurs like me and, well, the less capable among us, keeping them running most of the time. That's a decent record for any 20+ year old vehicle..
 
Last edited:
They are certainly different. Need a ball joint press vs just unbolting trunions.
It was removing the spindle to get get axle out that gave me the most grief.
 
Back
Top Bottom