Anyone tried these?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 1, 2006
Threads
28
Messages
191
Location
Utah County
This x 2. Ask youself, do you want to entrust your or your family's life to someone making 25 cent/hr?

I'll self plug here - if you want an inexpensive solution, I sell new terrain tamer birfs. Not made in China! Good quality for a non-OEM part that meets OEM quality

Regardless if you get from me or elsewhere, stay away from febest.
 
Replace them with stock Toyota birfs if you do a lot of street driving in your rig. Mine held up for 220,000 miles before they started clicking and I wheeled the truck the whole time. If you plan to do a lot of aggressive rock climbing and you don't put that many miles on your rig, you might want to consider chromally birfs.
 
Last edited:
You should just whittle splines into a broomstick and then cut 2 pieces to length and make a big ball of duct tape for the joint...probably work just as long...and it's cheaper. Seriously though, I know Toyota wants your first born child and a hand job for their birfs and understand the want to save money, but a cheaper alternative to factory Toyota birfield joints is nitro or trailgear chromoly birfs and shafts. If you don't plan to wheel it hard, just buy OEM birfs and call it a day. The old saying of "you get what you pay for" couldn't be more true with parts like that, I mean, imagine what it cost to manufacture a complex machined part like a birfield. Then look at how much they're asking...you should extrapolate from that logical thought process that the fit may be decent, but for the price, the material is likely garbage.
 
Our 80's are being treated like a wam bam thank you ma'am! Treat it well and the 80 will take you to places you have never dreamed of going!!
 
I have Nitro birfs from Slee. Only have like 15k of street miles on them, but they're doing fine so far. I'll probably get OEM if these wear prematurely.
 
OK OK I'll stay away from those garbage birds. I am well familiar with our 80s. This is our second one and have wheeled them all over.

This is mostly a street driving truck with one or 2 off-road trips a year. My plan is a full service in the front axle. I was planning on just cleaning and repacking the birds and swapping sides. Like I said the clicks are very quiet (unlike the last 80 we had) and only at max turn with a lot of skinny pedal.

I haven't checked the level of moly yet, but I do have some soul leaking out so I know there isn't enough in there.
 
Birfs can click if they're low on grease. Like tools said, I would check the knuckles before pulling everything apart if that isn't necessary n
 
I just did a full front axle service on my truck. If you haven't don't it before, be prepared for a good time ;-)

I parked in the garage for this one (expecting it to take a couple of days - which it did) and put down plastic under the entire front of the truck. Just the cheap painters stuff that I could roll up and throw away afterwards. This was probably the best move I made on that project. YMMV.
 
I've done the front service a couple of times before in previous 80. Since I have soup leaking, I'm just going to do the full service change bearings, seals and swap burfs for now. Thanks guys for the insight.
 
hey guys,

don't bash too hard the Febest.....At least for the bushings they are pretty good....I replaced the rear bushings on my Celica ST165 (DD) with Febest ...at the time the plan was I use them as a temporary solution until I get the OEM ones...Now after almost 4 years I'm still using the Febest bushings in the back for my Celica (this is my DD car...) they are quite fine so far....; the OEM ones are still in the original packaging ready to be installed...

regards
 
hey guys,

don't bash too hard the Febest.....At least for the bushings they are pretty good....I replaced the rear bushings on my Celica ST165 (DD) with Febest ...at the time the plan was I use them as a temporary solution until I get the OEM ones...Now after almost 4 years I'm still using the Febest bushings in the back for my Celica (this is my DD car...) they are quite fine so far....; the OEM ones are still in the original packaging ready to be installed...

regards

Bushings are a bit of a different story then Birfs.
 
Kurt at cruiseroutfitters.com sells everything you need in a kit
 
Back
Top Bottom