AC Drier Relocation fail

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 25, 2013
Threads
70
Messages
762
Location
Lakewood, Ohio
I was bending up my AC drier as I recently purchased and installed the trail gear front bumper and wanted the drier up out of harms way...all of the sudden

PSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSHHHHHHHHHHHHHHHHHHHHHHHHHHHHH

At first I thought to myself, f it nothing I can do and it hissed for a few more minutes. Then I decided to bend it back slightly and the hissing ceased.

Anyone been in this situation? Will it last?
 
Probably still leaking slightly just take it off and fix it those o rings have to be seated perfectly to seal may need a new drier ,enough Freon leaked out to where your AC won't cool right.
 
Likely cracked the line.

X2 ..

new line of fix this one ( alum weld ) if it's not mayor thing .. then vacuum the system, and refill . .
 
Thanks all for the replies!
 
Put it back to straight then pull vacuum on the system and see if it will hold. Also, whats the motive for bending it out of the way ? Have you hit it on something before ? Mine sticks out of the bottom of the shortbus and I've never bashed it. I think even slee hasn't bashed there's and they wheeled it pretty hard.
 
Put it back to straight then pull vacuum on the system and see if it will hold. Also, whats the motive for bending it out of the way ? Have you hit it on something before ? Mine sticks out of the bottom of the shortbus and I've never bashed it. I think even slee hasn't bashed there's and they wheeled it pretty hard.

Well...shoot. maybe i succumbed to forum brain wash...

image-jpeg.1250851
 
Paint your dryer flat black. That way the rocks and tree limbs won't be able to see it as an easy target.
^^ genius level s*** right here :hmm:
 
Paint your dryer flat black. That way the rocks and tree limbs won't be able to see it as an easy target.

^^ genius level s*** right here :hmm:

I painted the whole front area of the truck gloss black when I pulled the factory bumper, oil coolers, Ac dryer, bottom most section of condenser etc. I thought it looked cleaner.

On a side note, I did hit the factory bumper on a rock just in front of the dryer... Still a little leery of its location, Ac is important in Texas, and more so when I have ,y family.
image.webp
image.webp
image.webp
 
I have the MT tube bumper which comes with an AC drier guard incorerated and it got used regularly when rock crawling the 94 (RIP). My new 93 has the drier up beside the radiator which makes a world of sense. Perhaps you could source the lines and brackets from a 93 and relocate your drier up behind the core support and right beside the radiator.
 
... On a side note, I did hit the factory bumper on a rock just in front of the dryer... Still a little leery of its location,

If you are careful bending the lines, can move it up a bit, if needed make a skid/guard. Get a shorter one, IIRC from a Taco. Or have new lines made and relocate it to under the hood.

Ac is important in Texas, and more so when I have ,y family.

I have heard that it's too hot in Texas, so 80's cant be driven in the summer, maybe just upgrade to a 200?:hillbilly:
 
The ones I have seen taken out were done when the factory bumper got pushed back into them. I'm not sure people realize how far it sticks out and down making it much more susceptible to that then an aftermarket. Even my giant ARB bar that I previously had didn't sit as low as the factory bumper. Unless I was going hard core rock crawling, ( like I knew I was going to have to bash my bumpers up over things) I wouldn't be concerned. I've been able to drop mine into some pretty steep spots and never so much as touched the bottom of the Slee on anything.
 
The ones I have seen taken out were done when the factory bumper got pushed back into them. ...

Yep, the factory bumper is in the perfect spot to guillotine the lines off of it.

I have the mentioned ARB POS, play in the rocks a fair bit, have bent the bumper multiple times. Thought I would have taken the dryer out by know, but have failed at that endeavor. Would like to put a short one on it, we always do when servicing them, but the A/C works well, not spun up about draining it, thought I would drain it on a rock.....
 
Yep, the factory bumper is in the perfect spot to guillotine the lines off of it.

Thought I would have taken the dryer out by know, but have failed at that endeavor. Would like to put a short one on it, we always do when servicing them, but the A/C works well, not spun up about draining it, thought I would drain it on a rock.....

Pretty my here where I'm at, I may try and move it a bit, but don't want to try and bend brittle aluminum hard lines.
 
I think I'm going to go for the battery box location
 
Back
Top Bottom