72 FJ40 electrical gremlins

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 7, 2014
Threads
6
Messages
48
Hello folks

I have a bit of a weird question maybe you guys can help me with.

I have a recently acquired 72 FJ40 and im trying to sort out the horrific mess of a wiring harness that has been " customized" by the previous owners.

I want to eventually change it but dont have the time or money till summer time. so for now im just trying to get the lights and the turn signals to work.
Im putting in a stand alone turn signal harness which will cancel out the existing factory switch and wiring.
my question is if the turn signal plug is disconnected from the turn signal switch the headlights dont work.

i was wondering which wires do i need to jump out in the turn signal plug so that i can omit the turn signal switch.
Again this is a temporary hook up until i have time to put in a new harness.

Thank you in advance

Yury
 
Don't do that.... Fix the turn wiring you already have.

What I am about to suggest will take you most of a day if you have never done it, but will pay off BIG TIME down the road.

Start by cleaning the battery terminals and cables and verifying that you have a ground to the engine and the frame.
Pull each fuse one by one and use a Dremel tool with a small wire wheel to clean each end of the fuse and the clips that hold it in place. Or just replace all the fuses and only clean the clips. This is VERY IMPORTANT!!!

Verify that the White/Black wire coming off the fuse block is grounded. This is one of the main harness grounds.

Go to each front turn signal light. Remove the front cover, remove each bulb, test that every bulb works. Clean the base of the bulb then clean the socket the bulb goes into. The bulbs WILL NOT LIGHT unless the housing is grounded. Say this 10 times!!! The housing MUST BE GROUNDED!!! It grounds via contact with the sheet metal on the body. If there is rust, there is no ground. So remove the light housing and clean to bare metal or if your inclined, add a separate ground wire to the housing and ground under a bolt on the inner fender.

Go to the rear of the truck and repeat this process for the two rear lights. If you have side maker lights, repeat for each light.

Only now are you ready to even begin trouble shooting your issues.

Once you have done that then turn on the headlights. Do they work? Do you have park lights on all four corners and marker lights?
Turn on the HAZARD lights. Do all four corners flash? Do your dash indicators also flash?
Turn signals next....

Report back what you find....
 
Coolerman.

Thank you for your reply. when i turn the lights on all four corners light up (marker lights). the emergency flashers dont work. and neither does turning the turn signals on.

I have so far cleaned the turn signal switch and all related plugs. i have also checked the clicker relay for operation and that seems to work as well.

however when everything is connected the turn signals do nothing.

the one thing i did notice is when i press the brake pedal (which lights up the back) and operate the turn signal switch, one of the break lights will go out untill i put the switch back to off. if i remeber correctly it does that if the switch is in right or left possition.

Thank you again for your help
 
OK so no turn and no Hazard lights. Sounds like there is no power going to the Hazard switch which also provides power to the turn signal switch. My guess is a fuse or the fuse clips are dirty. You should have power to the Green/Red wire on the Hazard switch and through the Hazard switch out to the turn signal switch on the Green wire.
 
the one thing i did notice is when i press the brake pedal (which lights up the back) and operate the turn signal switch, one of the break lights will go out untill i put the switch back to off. if i remeber correctly it does that if the switch is in right or left possition.

This is normal behavior.

The hazard and turn signal power come from two different fused circuits that are switched at the hazard switch. Maybe both are bad or the switch is bad. To test the rest of the turn signal system, run a hot wire directly to the flasher and see if they light up. On one side they will light steady and if you run the hot to the other side they will blink if everything downstream from the flasher is OK.
 
Coolerman

i tried running a separate power source to the "b" side of the flasher to see if that is the case. still nothing. i also tried the same to the "l" side also nothing. maybe im doing something wrong. im going to try the terminal cleaning and see if that clears it up. To be honest this wiring harness is so hacked i dont even know where to start.

Thank you

Pin_Head
once i run the power to the flasher, im assuming i have to activate the turn switch to see the lights?

Thank you
 
Pin_Head is correct there are TWO sources of power. They are both Green/Red wires so they both should have power WHEN THE KEY IS ON! One of them will have power at all times to power the Hazards.

Do your brake lights work? If they work then you only have to fix the front turn lights.

The flasher will NOT flash unless a certain amount of current is flowing through it. For example if you had one front light out then the turn on that side WILL NOT FLASH as there is not enough current to activate the flasher. It would come on but not flash.
(This is where the LED flasher relays make trouble shooting easy: They will flash with NO BULBS installed! )

So... verify you have power to the two GR wires with key switch on. If you do then the Hazard switch could be dirty. Pull it out, take it apart and clean it up. Search for threads on this, there are several out there.
 
got it. so the the two wires i am checking are the ones on the plug for the flasher relay correct? one is always on and the other is on when key is turned correct?

I already took the flasher apart and its pristene inside.

Do you guys know where the power comes from to that plug? i know 1 is the #3 fuse from the bottom but where does the other one come from?

Thanks again

Yury
 
No you need to pull the electrical connector from the back of the Hazard switch and find the two Green/Red wires and check for +12V on each wire with the key on. My schematic shows the two fuses located second from the bottom and second from the top, but I cannot for sure state that is correct. Schematics are sometimes drawn for easy reading, not actual reality! I have a 72 harness at home I can check to see later this week.

Also the flasher could still be bad if you have never heard it clicking. If you have a spare swap it in or put your flasher in someone elses truck to verify it is good.
 
Coolerman

im assuming the hazard switch is the same as the turn switch? big square box by the clutch pedal with 2 wires coming out marked "b" and "L" or is there something else i should be looking for.

Im sorry for the stupid questions its just that this is my first FJ, ive only had jeeps before :)

Thank you again
 
once i run the power to the flasher, im assuming i have to activate the turn switch to see the lights?

Thank you

The hazard switch in in the center of the dash. Whether it blinks or not when hot wired depends on the position of the hazard switch. If pushed in, you need to turn the turn signal switch. If out, all 4 should blink no matter what the turn switch does.

Coolerman is right: you will hate yourself if you try to add new turn signals. Fixing the harness you have is easier even if it means you have to understand the wiring diagram.
 
The hazard switch in in the center of the dash. Whether it blinks or not when hot wired depends on the position of the hazard switch. If pushed in, you need to turn the turn signal switch. If out, all 4 should blink no matter what the turn switch does.

Coolerman is right: you will hate yourself if you try to add new turn signals. Fixing the harness you have is easier even if it means you have to understand the wiring diagram.
I will try everything. What i meant by the location of the hazard switch was actually the lpcation of the flasher relay. Or is it the same one as the turn signals flasher?

also what i meant by adding turn signals is that i wanted to get a trailer wiring adapter and just use another switch to get by this winter untill i can get to really tearing into it.

Thanks for your help guys.
 
OK you need to get the terminology correct before you confuse yourself!
The Turn Signal Switch is on the steering column.
The Hazard Switch is on the dash.
The Flasher Relay is mounted to the firewall under the dash. There is only one flasher for your year truck. It works as the flasher for the Turn Signals and the HAzards!!!

Go here to learn how the Turn Signal and Hazard Switches work: http://www.globalsoftware-inc.com/coolerman/fj40/6A.htm

Troubleshooting:
You need to locate the Hazard Switch in the dash, turn on the key, then get under the dash and unplug the 6 pin connector from the back of the Hazard Switch. Set your volt meter to DC then attach the black lead to a good ground (like a bolt head) then the red lead to one of the two Green/Red wires in the 6 pin connector. The meter should read +12.0V to 13.8 volts (depends on how good the battery is charged) If it doesn't check the fuses. Check the other Green/Red wire. You should have the same voltage. If not check the fuses.

Once you verify you have voltage on BOTH those wires, report back and we can continue to trouble shoot.

Oh and download the schematic for your truck from here :http://www.globalsoftware-inc.com/coolerman/fj40/schematics/ Scroll down to the 1972-1973 section then click on each of the two files there to download them to your computer. Then print them out for reference.
 
So i pulled the heater out and got to the hazard switch. (What a PITA) green and red wires have power to them.

So i guess the next step is get an LED clicker and see if the problem is there.

Any other suggestions guys?

Thank you all again.
 
While you are waiting on the new LED flasher to arrive: Take the Hazard switch apart, clean it of all dirt, clean the contacts, grease it and put it back together. If the switch contacts are dirty they won't make good contact thus causing issues. There are a couple of threads on MUD showing how to take the switches apart.
 
Thank you Coolerman. I did that when i took it out. Cleaned all contacts with emery cloth and even stretched the little springs out just a tad. Its nice and tight now. Also checked for continuity. Everything seems good.
 
Good deal! Hopefully your LED flasher will fix your issue. Remember if you get the flasher with the clicking sound it's a three terminal and requires a ground. I make an adapter socket for it.
 
Good deal! Hopefully your LED flasher will fix your issue. Remember if you get the flasher with the clicking sound it's a three terminal and requires a ground. I make an adapter socket for it.

Im hoping so. I really want to drive it finally without sticking my hand out the window. Im going to use this jerry rigged plug i have to see if it works. Thank you again for your help Coolerman
 
Back
Top Bottom