2F or SBC?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 2, 2004
Threads
81
Messages
602
Location
Western Slope, CO
Well I did a compression (dry) test today on my 74 and here's the numbers

75
115
95
90
75
95

I have the original F motor, I didn't do a wet test, cause it also blows oil out the tail pipe when you start it up in the morning. So I'm guessing rings?? The odo shows 56k (maybe 156K actual?) Just wanted some opinions on what route I should go. I would have to have someone rebuild it for me, as I don't have the tools or skillz for that. :eek:

Should I look for a 350 to put in it, TBI? Or maybe a 2F if I could find one that was in decent running condition. I realy don't want to have my 40 down with summer coming on, I'm just not sure that it will make it much longer.
 
Do some searching on the forum. There are a lot of opinions. Expect to spend 2-4K on a good rebuild. You can easily spend that much having a 350 installed for you.

Many opt for the used 2F. You can get one pretty cheap and it's easy. To put a nice fresh 2F in will be spendy. I want to say about $4000 for the engine and you don't have a core so it will be more. labor for a straight swap shouldn't be that much.
 
Pulling and rebuilding the original motor should be the quickest and easiest of the choices presented.
 
I wouldn't worry too much about the core, by the time you turn it in the cookie cutter autoparts won't know the difference between an F and a 2F. Then when it gets back to the Recon place it sits outside on a pallet until they get another order for one. Keeps them from having too many NEW engines holding their money. So by that point they will notice it isn't a 2F and they will just move it over to the other pile and wait until a F engine is ordered.

Sorry, use to work at AZ... should see the returns I have done :)
 
I was leaning towards the 2F don't they make a little more power than the F motor? If I were to rebuild the F who sells a good kit for it? I have only bought from SOR and they seem pretty proud of their junk.
 
Quickest & cheapest route is a used 2F swap or a 2F rebuild. The pistons & rings are more expensive for the F engine, making a little more expensive to rebuild. There's just no reason to build an F engine.

Before I would put a SBC in a FJ40 it would have modern power steering, 4 wheel discs and good suspension. The last thing most old FJ40's need is the ability to go faster :)

Ultimately it is your truck and your money, so make your choice and write a check. :beer:
 
The swap from an F to a 2F will be a busy weekend....the swap from the F to a 350 is much more involved, and can quickly be more expensive too.

To keep it simple, pick up the 2F, either as a builder or used/ready, and spend a few weeks preppin it...

however, the 350 TBI in my rig was $200 and included a conversion van....lucky deals are out there, but they never arrive when you are needy...lol
 
paclift out of CA sells 2F rebuild kits for about 500.00 bones last time i got a price sheet from them. Old grumpy dude runs the place, its really a fork lift kit but its the same thing. do some searchs for pac lift and you will turn up there phone number. Then you need to have the machine work done. In the end if you maybe able to find a good used 2f for less than 500.00 dollars and just swap it in...

Stew
 
did some searching on E-bay last night, not too many to choose from. So what year should I look for in a 2F? I don't have alot of cash to spend so I would most likely be looking for anything that runs better than what I have now. Is E-bay about the best place to find a used one? I've been searching the Phoenix paper also with no luck. If I could just convince my wife that we need another one for parts.
:D
 
I've been debating this again myself lately. My 2f is still strong, but i'm burning a little over a quart of oil every 500 miles or so. It's been like this since I've owned it, the compression is even 125-130 psi all across. The oil burning doesn't bother me much, but the truck stinks horribly like burning oil every time I get off the throttle .Just crusing down the road is fine. Very odd. I'm sure the weber carb with opne air cleaner and open valve cover breather don't help. In the corner of my garage I have a 93 tbi 350 sitting on an engine stand. It's been waiting over there patiently for a little over a year now. A wire harness, some rams horns,that chevy pickup y pipe, a marks adapter or an nv4500, a clutch setup, and i'm in business. But I do like my 2f. So for me i'm still debating. In my situation it will probably cost about the same to do a real good rebuild on the 2f, or swap in the 350. But if I were low on bucks, I would definately find a running 2f and swap it in. Somebody's gotta have one lying around they are willing to part with for a few hundred bucks.
 
The 350 swap will cost you a lot more time and push your cruiser quite a ways away from stock. There are a ton of guys that have done it, and there's a ton of public knowledge available, but it's not a trivial job.

Keep in mind that those of us that haved swapped to v8s have either plenty of time to do the work ourselves, or plenty of money to hire it out, or neither one and ended up with a can of worms.

From what you've said so far, I agree with the others; the 2F sounds like a good bet.
 
One thing that you may want to consider is that with a 350 if you have problems down the road it will be much cheeper and easier to replace. I am planning to remove a running 2f to replace with a 350 for mainly that reason. It has a bit of a tick and I am thinking that I don't want to dump more money into a 30 year old motor when I can buy a gm create motor for $1500. I realize the conversion will cost more than fixing what ever the tick is.
 
Jetboy said:
One thing that you may want to consider is that with a 350 if you have problems down the road it will be much cheeper and easier to replace. I am planning to remove a running 2f to replace with a 350 for mainly that reason. It has a bit of a tick and I am thinking that I don't want to dump more money into a 30 year old motor when I can buy a gm create motor for $1500. I realize the conversion will cost more than fixing what ever the tick is.

This is kind of my thought too. Another reason also why I want to use either a marks adapter or an nv4500 too. I don't want to deal with clutch mismatches 10 years down the road. Plus everyone I have met that has a properly done v8 swap says they are far more powerful (obviously) , steer better, are quieter, etc. But I like the original 2f too. I'm broke now (getting married in august) so i've got plenty of time to think about it.
 
A 2f would be what I would do. If you care, resale with a f/2f will be better then a SBC swap, and I must say I have seen very few SBC swaps that are done right, most are backyard butcher jobs that scare the crap out of me.
 
It has already been said, but I would vote for a used 2f.

Went through the same thing two years ago. The 350 is a great motor, but to not have a hack job conversion you are talking major bucks. Great power though, and oddles of aftermarket.

I went with a used fj60 2f, electronic ignition and it bolted right in. I had the head rebuilt, and installed new gaskets throughout, and detailed everything. I am happy with the power and cost, about 400 bucks in the motor and another 100 for the engine hoist.

I was actually really shocked at the power of a healthy 2f! Mine was always doggin' before. Drive both, look at the costs, stay toyota... or drop in a Z-06 corvette motor and sell it to me when you are done!

Rezarf <><
 
This may be the oldest debate in Cruiserdom and there are only individual answers. That means each owner makes up his own mind whether to convert or not.

SBC engines and cruisers go together like peanut butter and jelly - you used to be able to buy brand new vehicles converted by ConFerr or Downey, both of whom advertized the trucks in magazines.

If you want to get in touch with the costs and processes of doing the switch get the catalog from these folks: http://www.advanceadapters.com/newidea.html or just study their site.

SBC engines are some 300 lbs lighter than 2F or F engines. Parts are everywhere and cheap. The sound can be awesome.

Conversions can bring smog issues depending on your state law. Should look carefully at that factor.
 
Maybe I'm just being a loyal toyota fan, but I'm gonna look for a good 2F for it and keep things simple :D So I can pull any 2f (from a 60 too) to put in there? What should I look for? any years better than others? I have the old points style ignition, so I would be looking to upgrade that in the process.
Hey my neighbor has a nice 84 FJ60 in his driveway :idea:
 
fj60, or 8/81 fj40 would be what i would go with if possible, but you can swap the points out for fj60 elec ignition in any 2F.

wtmtnterror said:
Maybe I'm just being a loyal toyota fan, but I'm gonna look for a good 2F for it and keep things simple :D So I can pull any 2f (from a 60 too) to put in there? What should I look for? any years better than others? I have the old points style ignition, so I would be looking to upgrade that in the process.
Hey my neighbor has a nice 84 FJ60 in his driveway :idea:
 
78 and up 2f's had the electronic style ignition. I would suggest finding a donor vehicle and taking EVERYTHING you can in one swipe, this will help. Like getting the coil and ignitor for the ignition, starter (sometimes they are different sizes) Air cleaner assemblies, EGR stuff, alt.

I would also look for a 60 2f, usually lower miles, and they are drilled for power steering for down the road, and the 60 pump bolts right up.

Just another .02 so I guess I am up to .04 now.

Rezarf <><
 
love the sbc, super cheap to fix and you can find good engines cheap. i didnt care if mine was stock or not so it was not much to think about. love it
 
Back
Top Bottom