289w fj40

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 23, 2014
Threads
2
Messages
18
G'day from down under,

Long time reader, first time poster.

I've got a spare 289w from the mustang project, and the ol' 2f in my 77 FJ40 was on its last legs, so figured, why not!

I've purchased a Mark's 4x4 adaptor kit, which doesn't include engine mount posts. I've organised a fabricator to come out and make some for me, but need to make sure it is in the right position.

It seems rather low to me, but if I jack up the front, the gearbox fouls on the bash plate.

My question is, at what hight should the front of the engine sit? The rear is pre determined by the bellhousing mounts, but the front can be raised or lowered quite a bit.

I will attach a few photos when I get the computer back off the wife.
 
I did not realize that there was an adapter for a 289 to the stock Toyota transmission. I'm afraid it's not going to be as easy as you think, and will probably involve more than adjusting the height of the engine in the bay. I am running a 283 Chevy V8 in my truck. It was converted (poorly) before I bought it, but here is what I learned so far - it may be something to get you started.

Generally speaking, Chevy V8 conversions do away with the bellhousing mounts and instead mount via the "propeller mount" off the back of the transfer case. Might be different for Ford. This is because V8's tend to be shorter than the inline 6's the trucks came with. They usually need to be adjusted front/rear in the engine bay. If the engine is too close to the firewall, you get poor airflow around the engine, and cooling issues. Moving it forward to get proper distance to the radiator and proper airflow, on the other hand, involves modification to the drive-line location. Pay careful attention to your driveshaft angles in the engine bay - you don't want to mount the engine so high that your driveshafts need to run at an extreme angle to get down to the axles. This results in premature wear and driveline vibrations.

The standard issue most run into is to get the engine close enough to the radiator, the entire driveline needs to be shifted forward, resulting in the transmission's shift tower locating under the heater inside the FJ40's cab. The shifter must then be dog-legged (bent) under the heater and out. This also involves "modifying" (cutting a hole in) the transmission tunnel do to the shift tower relocation.

Last but not least, driveshaft lengths generally need to change. Since the engine/transmission/t-case wind up further forward, the front driveshaft needs to be shortended, and the rear one lengthened, to compensate.

My truck had a conversion done rather poorly at some point in its life. It is a good example of an extremely (too far) forward mount of the V8. My fan is almost up against the radiator, which in turn means my transmission/shift tower is right up against the firewall. The results in about an 8 inch dog-leg under the heater, and the world's longest, un-ergonomic shift throw and driving position you can imagine. It's on the list of things to address (there is a long list).

Cdaniel did a very nice V8 conversion on his truck. Again, this was Chevy, but it's a good example of how the conversion SHOULD be done, where as mine is an example of how not to do it.

Some shots of my conversion, which, again, is mounted too far forward. If I re-do it, I'll be shifting everything backward in the bay several inches:

FJ40 No cowl.webp


FJ40 Guage Cluster.webp


IMG_0534.webp


Heater Hoses.webp


New Air Cleaner.webp
 
My point wasn't that small block Chevy's are more common, I'm just trying to provide advice based on what I know. I've seen Ford V8 conversion as well. I'm sure it's possible, my guess is that the OP would run into the same pitfalls - regardless of whether he uses a Ford or Chevy V8.
 
I started looking in to the conversion in Feb, rang a few places, Marks 4x4 only made a kit for a clevo. I made a few more enquires last month, and they have started producing the kit for SBF again. They discontinued it for a long time, but they had enough enquries to warrant building them again.

The kit incudes a bellhousing adaptor, which bolts to a 4 or 5 speed FJ40 gearbox, bringing the whole engine forward 6 inches. Leaving the Box and driveshafts untouched. It also includes a spline adaptor, which slips over the Toyota gearbox input shaft and has a standard ford pattern, allowing standard ford parts to be used, i.e, pilot bearing, clutch and pressure plate and flywheel.

They still had the old instructions on file, which they used with the new kit, and they mention several times how to mount the engine, but they haven't started re manufacturing them yet, if at all.

Attatched are some pics, showing the aluminium adaptor, and where the engine wants to sit. So as long as the driveshafts aren't at silly angles, it should be ok?

DSC_1822.webp


DSC_1823.webp


IMAG0105.webp


IMAG0106.webp


IMAG0107.webp
 
grrr, damn computer. sorry for the double post.

Last pic if from the top, showing how much the engine has been moved forward

IMAG0114.webp
 
Definitely interesting. I do not have the experience with either the Mark's Adapter or Ford V8's to provide a lot of insight here. If the engine is mounted close enough to the radiator to get proper cooling (without the fan eating the radiator under flex, as I worry mine would) then you should be golden, front to back. Height, at that point, could probably be determined by driveshaft and hood clearance.

You mentioned that, after a certain point, the gearbox "fouls on the bash plate." Forgive me, but my Australian is rather poor - what is the bash plate? Firewall? Or the skid plate below the transmission? I know on my 350 conversion, it sits a little lower than stock, and the skid plate is gone, as a result.
 
Yes, the bash plate is the skid plate.

I think I've come to a happy medium, I'll modify the skid plate a little to get the clearance I need.

The engine isn't quite horizontal, the front points up a little. And the fan is still about 2 inches below the bottom of the fan shroud. (Electric thermo fan, here we come.)

The driveshafts don't seem to be at any excessive angle, and there is plenty of hood clearance.

The fabricator should be coming out this week or next, he owns ol' school customs here in Tamworth, and builds hotrods, so I'm sure he'll have an idea or two.
 
Im glad you are doing this. I may eventually do a swap from a ford explorer 5.0.

Have you tried just flipping the fan shroud upside down? You can run a plastic fan with a fan clutch from a modern 5.0. I would stay away from electric fans. Fj40s seem to issues with v8s and electric fans. There is about 1 post per week here on the subject.
 
I like your project, looks good. I usually figure about a 5* tilt to start. I've also sometimes added more angle to deal w/driveline angles or major clearance issues. The concern I see from your pics is the distance between the frt diff & the oil pan.
 
SBCs are known for having potential problems with the harmonic balancer hitting the diff at full compression... Some use a smaller balancer to help limit this. I'd likely ditch the stock bash plate and build a custom one... Most stock ones I've seen have been mangled by rocks.

I lowered my stock rad to keep a mechanical fan (SBC). Many electric fans just can't keep up with the demand.
 
I changed the pan to a Bronco rear hump style, but still might be able to modify the front bit to get a bit more clearance there.

I'll try turning the shroud upside down, only issue I could see is it'll be off center on the wrong side. I've ran an electric fan off this v8 in the mustang for about 3 years, i'll see what happens.

Maybe if I raise the bellhousing mounts and inch or two, i'll have to see how much spline is left in the transfer, but that might ease things up.

The skid plate is in really good condition, but i have the means to make a custom one if needed.

Thanks for all the help. Greatly appreciated.
 
I’m curious how your SBF conversion panned out. I’m in the middle of a 351W swap in my 45. I’m using the Mark’s kit as well. Not too many Ford swaps around here!
 
Back
Top Bottom