oem

For Sale: OEM roof rack from 2004 LX470. Comes with everything ready to mount. Location: Riverside, CA Local pickup only $100

Looking to buy a driver's side front door speaker. Mark Levinson. 2002 or earlier. Thanks

90 HDJ81 with factory winch. What are the factors that may reduce the pull strength of a factory winch? I went to use it for the first time and found it’s pull no what I would expect from this winch. I’ve used other winches so I have a feel for winch strength and this one seems to stall far...

This was pulled from a 72 (or 73) model. Its not perfect but its original. Its got a tear (visible in pic) on the front tranny hump section. Its also got a hole (shown) on rear section (towards the left side) and a small hole above toyota logo on the drivers section. Again, not perfect, but...

UPPER DASH PAD IS SOLD Cleaning out the shop and came across these,I must have been hoarding these for over 10 years now.Time to go ! The upper dash pad is from a BJ40 and is in good condition except from the fact that some dumbass po painted his windshield frame on the inside with the cover...

Thanks in advance. Looking for 4.

As the title states, I am looking for 4 to 6 18in 100 series wheels that are in good condition. I am located in SoCal and local would be best. Thx Sean

I am running a brand new oem thermostat but my cruiser has been running pretty hot lately. I know the OEM is 180 degrees but anyone know where I can find an aftermarket that works at 170? I realize it could be something else but I do want to start with the thermostat.

Front and rear springs are from a 1997 LX 450 with 230k miles. Also have a set of monroe or some yellow type (not OME) of shocks for F&R. I'd prefer not to ship but if so, buyer pays actual shipping. $80 for the springs for both F&R. I'd like a 6 pack of beer or equivalent for the shocks...

Sold

I want to change my existing 16" split rim with 7.50 x 16 tires to an OEM 15" rims with 215/75r15 tires. This will inevitably put the speedometer out as the 7.50 x 16 tires are about 4" bigger in diameter than 215/75r15 tires. Hence, I will need to change the gear ratio for the speedometer...

I am getting ready to make some replica power steering pump brackets for the FJ40 Land Cruiser. They will be based off of the original bracket and looks very similar. I wanted to see if anyone would be interested in them. The bracket will be for the 1979 and newer FJ40's that mount to the...

Genuine Toyota tie rod ends. Fit 64-83 FJ40, 45, and the 68-80FJ55. They are for the main steering rod. $120/pr shipped. No PMs please.

Getting rid of my 2000 Toyota Land Cruiser w/very low miles (89,187 miles as I write this), it's in excellent condition. I've recently completed some preventative maintenance including OEM CV joints, both front power door lock regulators, and timing belt all completed at my local Toyota dealer...

Parts sourced via @beno 4 Runner arms get you a better contact patch with modern wipers. The bushing on the wiper motor on my 1984 was a goner. My wipers slapped time on the cowl and went about 4" off the windshield. OEM Linkage is still available. I removed the entire linkage with...

Looking for an Oem pto winch to fit an 84 bj42lv, will piece together if partial units are out there but will require the correct size driveshaft . Will require shipping to southern Ontario. Thanks

I have a set of OEM tinted tail lights (top four) from a 2013 200 series. PO had them tinted and it is illegal in our state to I purchase a new set. New one cost me 500.00 so anyone interested for 200.00? PM me if you are interested in pictures.

Sold! Thank you. Mods Sorry I'm not sure how to delete the thread

I upgraded my 97 to after market speakers and have all 8 working original factory speakers. Rather than throw them out, I figured someone on the board here could use them. Who needs?

Hi All, I have a 1979 BJ40 with rear jump seats (and no seat belts) and would like to fit the rear 4x lap belts. Were they fitted as standard (the BJ40 is french model)? And if so, I would like to know where exactly they were bolted on - as if I need to drill holes in a good condition original...