carburator

Hi Guys, First post on the Forum, so sorry if im not in thr correct section. I'm busy restoring a 1995 80 Series GXL model with the 1FZ-F motor I need some help with regards to a Service Manual and a Electrical Wiring Diagram, i have downloaded a few on the resources page but all seem to be...

Hey everyone! First time posting here so I hope I don't step afoul of anything. I've searched high and low thru the forums to find the answer to this question so posting has been my last resort. I am in the process of trying to get my 84 FJ60 up and running. This is my first *car* project (I've...

Hey guys was wanting some help figuring out this carby. I bought this land cruiser and it came with this carburettor with most the ports being in the same place but the advance vacuum port missing and the idle solenoid port missing as well. What can I do about it or do I have to purchase a new...

HELP! My late husband did a frame off restoration of a 74 FJ40. A Weber carburetor was installed by a friend a while back. I have had nothing but issues with this carburetor. The car is running like Sh*t (constantly backfiring, no power, stalling etc) and I am being told the carburetor...

Hi All Im facing an issue with the Carb of my recently acquired FJ40. After some observations and suggestions from a fellow member, I've identified that my carburator is leaking gasoline. This wasn't initially apparent, but after running the engine for a warm-up as part of an oil cleaning...

First off, a sincere thank you to everone on this forum for the warm welcome and responses to my posts. I’m digging in and learning a ton, and I hope to contribute more along the way. I’ve had my ‘76 almost a month and I’ve gone over the ignition system, discovered a faulty coil, replaced plugs...

Hey, This is my first post on this forum and I am happy to be one of its members. I have a problem in my FJ73 3F engine with the carburetor, it was not original, and I bought a new original carburetor. But I noticed that the distributor need to adjustment, and I set it well, but the problem is...

So Guys I LOVE my FJ40 but VERY frustrated with my Intermittent Startup issues - hope you can help. A bit about my FJ40 - New Batery, Cables, Sparkplugs, Startup coil (Internal Resistor). - Stock Carb (to my knowledge) - Stock Distributor (to my knowledge) - Has the Evaporative Emissions...

Ok so this is an on-going saga that has been happening with BeBe since I rebuilt the top end in 2015/2016. She is a 85 FJ60 with the original 2F in her, desmogged when I first got her due to the smog pump being seized. Issue: - Truck will idle high after it has warmed up. Talking between...

I have had to leave the choke slightly out on my 1977 FJ40 so I don't stall at lights. My over zealous father in law made some funky adjustment to the carb and now it stalls at lights. I had read a post that someone had placed on here with simple instructions and a diagram. turn idler screw 3...

HEllo, Pretty new here. Have an 84 fj 60 that was desmogged by po. Has a holley carb. Nice little rig. 300k on it but pretty clean. Anyway, am looking at some possible upgrades for performance/ fuel economy. Not a mudder. Just a daily driver. Any thoughts as to brands , models etc would be...

Two carbs for sale. One is missing the choke opener and it’s linkage. I was told had been rebuilt at some point in the last handful of years. Was on a running truck maybe 6 months ago. $100/BO. 1st three photos. Second is cleaned, dissembled, comes w/ extra jets. I can put it back together...

hey! I recently purchased a 1980 FJ40 that is in need of a few parts to get her on the road. Blair from Tommy's Automotive has been absolutely awesome at providing some guidance and help along the way. I've got most everything sources to get her roadworthy again, but I'm having challenges...

Hello All, I have come to the realization that multiple people on this forum are in need of a SD-40 Large window sight glass. I would love to have an original but I know that that may only be a dream. In the mean time, I am probably going to make my own. I would be willing to make a few extras...

Starts fine with choke and idles easily. After I start driving there is a hesitation as I accelerate and it feels like it is not getting fuel. If I push harder on the gas she'll finally open up and go on down the road. If I leave the truck in the garage you can smell the gas like there might be...

I have been using the Weber 38 DGMS on my FJ80 3F engine and works just fine. I live in Bogota, Colombia, meaning +5K feet above sea level, but I have been wondering if the carburator really makes a significant difference on my rig considering it has headers. Also carries 35¨ tires and stock...

I know, I should pay more attention it's been discussed before... I need someone to rebuild a california 1978 carburetor that is disassembled in a box. Don't ask any questions, I don't wish to discuss the details. Lol Anyone out there that does good work without laughing at me? (I couldn't do it!)