bell housing

For sale are what’s left of my F engine and drivetrain. I have a 3 speed manual transmission and transfer case - $1,000 I will sell separate but you have to do the work and would like to sell this locally. Shifter with new 3 speed knob - $125 front and rear drive shafts - $150 exhaust...

can be from 1hz, 1hdt, 1hdft or 1hdfte let me know what you have, thanks.

Have a nice condition bell housing from a 82 fj60 2F. Has the 3F stamp on it. Also have the inspection cover in great condition. Willing to ship at buyers expense or local pick up around PDX.

This is a bell housing adapter for a 350 SBC to the Toyota 4spd. It came off of a 1976 FJ40. Located south of Winnipeg, Manitoba. $350 OBO.

I believe that this would have come out of a 1990+ European market bj73 May be part number: OEM Toyota 31111-60160 Any information on a source would be greatly appreciated.

Some miscellaneous stuff from a parts rig. Unknown/untested, consider these cores. PayPal only, add actual shipping to all prices. More photos upon request. Open to reasonable offers. SOLD Roll bar pads, good shape - $40/pair SOLD License plate holder with lights. Lenses intact, zero rot...

Have an inspection cover from a 6/86 FJ60. Will fit any of the later 3F bellhousings used from 85-87. Needs a little more cleaning and some paint and it'll look brand new. $175 + the ride

I am looking for the mounting brackets that bolt on either side of an early FJ40 three speed bell housing, as shown in the picture below. These are the brackets that hold the mounts that attach to the frame. I have the correct bell housing, I just need the brackets. Thanks…

Looking for a serviceable bell housing that would fit a j30 3spd from early 70s 40 series. Preferably in easy distance from Portland Oregon metro area. Haven't priced these. I have a few things to trade but can do cash. Hoping less than $75

So I am stuck on the routing of my 3 speed linkages. I seems as though one of the bolts that mounts the bell housing to the frame is too long and would hit the fly wheel. There was a pivot so I bolted the mounting bolt through the pivot and it didn't allow the gear shift to pivot. I am just...

bell housing and torque converter have 137k miles all other parts have 270k miles. power steering reservoir $18 a442f 1fz torque converter $40 a442f 1fz bell housing $40 throttle cable $20 cruise control actuator $50 Exhaust down pipes $30 very muddy in the picture but not rusty aftermarket tail...

I’ve got what appears to be 2 mounting brackets from a 4-speed bell housing. Need confirmation on that and which one goes to the driver side.

I have a 2F engine paired with an H42 transmission. Besides the H41 and the H55 what transmission would directly bolt to the H42 bell housing or to the 2F?

I have a 2011 LX570 with 200k miles. I was replacing a u-joint on the front drive shaft when I noticed evidence of a coolant leak. It appears to have been leaking for a while but not enough to make it to the garage floor. It's hard to see where it's coming from but I can see most of the leak...

Hi All Just noticed that there is a hell of a rattle coming from this area on my high mileage lx470. What it sounds like is a thrust bearing but this being an auto .... Anyone have any experience with this as a common point of failure?

‘79 FJ40 4 speed transmission and transfer case. Purchased from a fellow Mudder years ago and never used. Been stored inside a shed since I had it, but looks like it may have been outside before. Price $300 local pickup ‘79 Bellhousing 2F $100 local pickup ‘79 Flywheel 2F $75 local pickup...

Hey I am sure this is already on the forums somewhere but - I am starting to buy parts for my eventual sbc swap back to a 1f or 2f engine. I want to keep the 3speed transmission so I can swap it back to column shift. I found a 2f bell housing with the clutch fork for a good price. My...

hello guys, i have a 62, and i wanna do a 3uz swap with the same transmission (A440F) but i dont know what bell housing works for that. if anyone knows it would be very helpful!

Hi, I'm just north of Portland. Need a bell housing for my 73 FJ40 as my current one cracked. Thanks!

hi everyone I’m looking for bell housing 1hdt - 1hz to trans h55f I think parts number 31111-60230 And input shaft 3111-60170 Thankyou