Don't know if this reservoir is from a 60 or a 62 series as it was not tagged. Take a look at it and decide if you need it. Cap looks good and the motor is there. Price $50 buyer pays shipping. Best to email me shmukter@pa.metrocast.net
Hey group..i have a 62 with a Cummins 2.8 swap….colder temps have set in and i cant get the heat to get really hot…..kinda strange…here is the other issue, when i turn off the rear heater (slide to the white dot) it will then make the air turn coled, if I turn the rear back on, air turns...
Hi Folks,
After looking through the FSM and reading several promising threads here, I'm still at wits' end. Any input is greatly appreciated.
My 62 stalled at the intersection. It would restart but would stall again when put into gear. I could give it plenty of fuel while in Park or Neutral...
Hey, Cruiser Trash Parts here…
I’ve been offering laser cut ABS cargo panels for 60/61s for a while now and finally released the 62 versions this week! I now offer cargo panels for any 60 Series variation, including some of the rarer HJ panel variants - 7 variations in total, plus options for...
https://vintageteqparts.com/collections/everything-else-hardware-fsms-shop-manuals-special-teq-stuff/products/copy-of-12v-genuine-nippondenso-japan-spec-oem-toyota-rear-windshield-washer-reservoir-bag-bladder-w-pump-sub-harness-green-tint-hose-fj60-fj62-hj60-bj60-hj61-12v
( NEW PRODUCT RELEASE...
Looking for a new distributor unit for my 62. Are these available new OEM anywhere without an exorbitant price?
If not I guess I’m on the hunt for some high quality used sources that have been cleaned and tested.
Thanks!
I just got a new code cut key for my 62. most of the door locks work fine. Driver door lock seems be funky. The key will sit at a downward angle and wont work. Hold the key up and level anf it works fine. Any idea how to work with cyliner to adjust this wear or slop?
Thanks.
Hey guys, my only experience with a LC has been a fantastic 200 series. I’m looking to go back to an LC and I found an 85 62 series, that had a body off frame restoration, looks great, no rust. It’s a manual with the 3f engine., AC working, seats look new, pretty flawless for the age.
I looked...
I have been looking for a clean (rust free) FJ 62 or silver 60 for some time and can’t seem to find what I’m looking for. Figured I’d see if anyone was on the fence about selling.
Would prefer mostly stock/original and under 200k miles. My price range is ~$20-30k depending on the condition...
Unfortunately the time has come to sell my baby (nicknamed Ruby). It's been a hell of a great camping rig, and has gotten me everywhere I've ever wanted to go and never left me stranded. Wish I could keep her, but selling because I need a larger truck for towing a camper. See details below...
Rear brakes are dangerously weak, so I took a look-see. Didn't even have to pull a tire... both brake backing plates are showing drooling. Probably not wheel cylinders, but I added a pair of ADVICS to the order for good measure. I also added a pair of outer axle seals which I think are the...
Hey guys,
Looking at starting a rebuild on my 62. I just wanted to get some input on the rust of the vehicle at the moment?
Thanks for your time in advance!
C
Hello fellow Cruiser Heads! We are extremely excited to start this build thread. Some of you may recall our first Classic Cruiser Giveaway FJ40 that we gave away to Joe Arellano in Houston, TX. Well we are back at it again and this time we are going to give away this beautiful 1988 FJ62!
So...
I don’t have a lot of info on the history. I bought it from a Cruiser dealer here in OKC. It had 73k. miles. Needed some body work and looked like it had been sitting for a long time. Normal mechanical work done (new alternator, radiator, thermostat, water pump, exhaust and master cylinder). No...
Im looking for just the service ports off the AC compressor, this style. The part held in the hand in the first pic. Second pic shows it mounted to the compressor. I dont need the entire compressor.